Reported-by: NDennis May <dennis.may@wolfsonmicro.com>
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This part of bias settings are essential for WM8962 to power up. Without it
"wm8962 0-001a: DC servo timed out" might be prompted due to power-up failure
that happens to FLL if being used.

The driver's also bringing the bias down in the suspend path so it needs to be
powered up in the resume path for symmetry.

According to dapm_pre_sequence_async(), DAPM would call pm_runtime_get_sync()
to let driver finish the bias settings in pm_runtime_resume() before the bias
level being set to STANDBY. So no need to worry about disordered settings for
VMID of WM8962.
Signed-off-by: NNicolin Chen <b42378@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Also fix return values for headphone switch updates.
Signed-off-by: NNicolin Chen <b42378@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org

This fixes:
975:9: sparse: Using plain integer as NULL pointer
1917:24: sparse: symbol 'rt5640_aif_dai_ops' was not declared. Should it be static?
1924:27: sparse: symbol 'rt5640_dai' was not declared. Should it be static?
2079:19: sparse: symbol 'rt5640_i2c_driver' was not declared. Should it be static?
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Modify the RT5640 driver to parse platform data from device tree. Write
a DT binding document to describe those properties.

Slight re-ordering of rt5640_i2c_probe() to better fit the DT parsing.

Since ldo1_en is optional, guard usage of it with gpio_is_valid(), rather
than open-coding an if (gpio) check.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Certain use cases may require specific DRE settings so expose control
of these.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch adds the ALC5640 codec driver.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NBard Liao <bardliao@realtek.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This driver is useless if both SPI and I2C are not configured.
Thus don't build this driver if both SPI and I2C are not configured.

This patch silences below build warning if both SPI and I2C are not configured.

  CC      sound/soc/codecs/adav80x.o
sound/soc/codecs/adav80x.c:842:12: warning: 'adav80x_bus_probe' defined but not used [-Wunused-function]
sound/soc/codecs/adav80x.c:863:12: warning: 'adav80x_bus_remove' defined but not used [-Wunused-function]
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Some runtime-determined constraints might need to be satisfied prior to
firmware loading, so the actual download and releasing the device from
reset has to be postponed. Factor it out first, so we have everything at
one place.

This also changes the behaviour in a way that adau1701_i2c_probe() will
assert the reset line, and wait for the codec probe to release it.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Otherwise, ssm2518_set_tdm_slot() always returns error if slots != 0.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

We should use i2c_get_clientdata() to get the codec private structure.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

On a mx6qsabrelite board the following error happens on probe:

sgtl5000: probe of 0-000a failed with error -5
imx-sgtl5000 sound.13: ASoC: CODEC (null) not registered
imx-sgtl5000 sound.13: snd_soc_register_card failed (-517)
platform sound.13: Driver imx-sgtl5000 requests probe defer

Prior to reading the codec ID we need to turn the SYS_MCLK clock, so let's
enable the codec clock inside sgtl5000_i2c_probe().

Also remove the codec clock enable/disable functions from the machine driver.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

When calling snd_soc_dapm_sync(), it eventually tries to lock the same mutex
already locked in snd_soc_dapm_put_volsw_aic3x() and a deadlock occurs. By
moving the mutex unlock to just before snd_soc_dapm_sync(), this deadlock is
prevented. This problem was introduced in Linux 3.5
Signed-off-by: NAndreas Irestål <Andreas.Irestal@axis.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Otherwise the functions will be defined but unreferenced when runtime PM
is disabled, generating warnings.
Signed-off-by: NMark Brown <broonie@linaro.org>

When the regulators have been disabled mark the device as cache only so
that we don't try to interact with the hardware.
Signed-off-by: NMark Brown <broonie@linaro.org>

to support HDMI on CSR SiRFprimaII and atlasVI, we need one more HDMI pseudo
codec, rather than add a new driver, we can make omap HDMI codec common for
other SoCs as well. then the omap-hdmi codec becomes a generic HDMI pseudo-
codec as HDMI audio features depend on HDMI specification not on SoCs.
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

All sources and sinks should enable SYSCLK.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

The VAG_POWER must be enabled after all other bits in CHIP_ANA_POWER
and disabled before any other bit in CHIP_ANA_POWER. See the SGTL5000
datasheet (Table 31, BIT 7, page 42-43). Failing to follow this order
will result in ugly loud "POP" noise at the end of playback.

To achieve such order, use the _PRE and _POST DAPM widgets to trigger
the power_vag_event, where the event type check has to be fixed
accordingly as well.
Signed-off-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Both clear the IRQ as being a wake source when we are finished with it
and include a missing header file that is required.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The DSPs IRQ should be a wake source as several of the possible
algorithms may run whilst the AP is asleepi and require to wake the AP
to push or pull more data, such as compressed playback.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NNicolas Schichan <nschichan@freebox.fr>
Acked-by: NBrian Austin <brian.austin@cirrus.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NNicolas Schichan <nschichan@freebox.fr>
Acked-by: NBrian Austin <brian.austin@cirrus.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The default register value for MASTERA_VOL is 0x00, the same as
MASTERB_VOL.
Signed-off-by: NNicolas Schichan <nschichan@freebox.fr>
Acked-by: NBrian Austin <brian.austin@cirrus.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

The array 'drc_cfg' of size 3 may use index value -22 (EINVAL)
The array 'retune_mobile_cfg' of size 3 may use index value -22 (EINVAL)
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Rename `dirty' to `set' as it is a bit more descriptive.  A set
control is any control that has been set by the user.  We need to ensure
that everytime we boot the DSP we sync out any controls that were
set.

We could at some point start keeping track of the default values of
the controls to suppress some of the device I/O.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

During recent refactoring the code to report removal when MICDET reports
an absent microphone was removed, causing problems for systems which rely
solely on the MICDET for this functionality. Restore it.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Define ab8500 codec operations structure on its own rather than inline
with snd_soc_dai_drivers to clean up the code and make the style
coherent with other codec drivers.
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Apart from pure matching, the bindings also support setting the the
reset gpio line.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds a ASoC CODEC driver for the SSM2516. The SSM2516 is a stereo
Class-D audio amplifier with an I2S interface for audio in and a built-in
dynamic range control processor.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

Pass a struct i2c_client * to adau1701_load_firmware directly to make
the code more readable.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The mask should define the bits to change in the register, not the
bits to preserve.

This fixes the inadvertent changes of the "Headphone Analog Gain"
value during mute/unmute.
Signed-off-by: NNicolas Schichan <nschichan@freebox.fr>
Acked-by: NBrian Austin <brian.austin@cirrus.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NNicolas Schichan <nschichan@freebox.fr>
Acked-by: NBrian Austin <brian.austin@cirrus.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NNicolas Schichan <nschichan@freebox.fr>
Acked-by: NBrian Austin <brian.austin@cirrus.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

DFBM-CS320 is only one of bluetooth modules using CSR bluetooth chips,
we don't want everyone to have a seperate codec driver. anyway, the
feature of Bluetooth SCO is same on all platforms, so this patch
makes the DFBM-CS320 driver become a common BT SCO link driver.
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Replace hard coded rx slot numbers from ab8500_codec_set_dai_tdm_slot
using the ones requested by the machine driver in rx_mask instead.
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>