USB should not be having it's own printk macros, so remove warn() and
use the system-wide standard of dev_warn() wherever possible.  In the
few places that will not work out, use a basic printk().
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Similar to the existing IRCONTROL4 handling
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Commit 8006479c introduced a spinlock in
input_dev->event_lock, which is locked when handling input events.
However, the hid-pidff driver sleeps when handling events as it waits for
reports being sent to the device before changing the report contents
again.
This causes a system lockup when trying to use force feedback with a PID
device, a regression introduced in 2.6.24 and 2.6.23.15.

Fix it by extracting the raw report data from struct hid_report
immediately when hid_submit_report() is called, therefore allowing
drivers to change the contents of struct hid_report immediately without
affecting the already-queued transfer.

In hid-pidff, re-add the removed usbhid_wait_io() to
pidff_erase_effect() instead, to prevent a full report queue from causing
the submission to fail, thus not freeing up device memory.
pidff_erase_effect() is not called while dev->event_lock is held.
Signed-off-by: NAnssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Fix hiddev.h example code.
To get the correct usage code, you need to set report_type and
report_id.
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Fix mixed space and tabs in example code.
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Since we have a real device bound to a driver, we may use struct
device for printing. Use dev_* functions instead of printks in
4 drivers.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

hid-ff.c now calls only pidff (generic driver), the special ones are now
in separate drivers. Invoke pidff on all non-special directly.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Move the force feedback processing into a separate module.

[jkosina@suse.cz: fix Kconfig texts a little bit]
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The bound check on the buffer length

	if (count > HID_MIN_BUFFER_SIZE)

is of course incorrent, the proper check is

	if (count > HID_MAX_BUFFER_SIZE)

Fix it.
Reported-by: NJerry Ryle <jerry@mindtribe.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

hid_compat_load() runs on the default workqueue, it request_module(), it
execs modprobe, it exits, tty flushes default workqueue, it hangs, because
we are still in it.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Tested-by: <Valdis.Kletnieks@vt.edu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

iBuddy devices claim to be HID devices, but they are not.
Add them to the blacklist.
Signed-off-by: NRemi Cattiau <remi@cattiau.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This patch fixes a problem that MacBook JIS keyboard sends wrong report
descriptors. Although it has already been fixed in the first Core 2 Duo model,
it still remains in other models of MacBook.
Signed-off-by: NTomoya Adachi <adachi@il.is.s.u-tokyo.ac.jp>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Fix config symbol name in ifdef to fix build error:

ERROR: "hid_compat_gyration" [drivers/hid/hid-dummy.ko] undefined!
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Acked-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Current kernel has no support for autocentering for Logitech wheels.  By
default autocentering enabled in wheel and constant effect does not work
properly. Using USB sniffer I found command which change autocentering
settings: 0xFE, 0x0D, 0x0R, 0x0L, 0x80, 0x00, 0x00, where R - clockwise force,
L - counter-clockwise (0x0-0xF, 0xC = 100%).
Signed-off-by: NSergey Belyashov <Sergey.Belyashov@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The Kconfig option for HID_COMPAT should read "lose", not "loose".
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This seems to be the very same device, as already supported Smartjoy
dual Plus, but with slightly different vendor ID. Let's support this
one too.
Reported-by: NDavid Ashley <dashxdr@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This patch reverts the change made four years ago here:
http://www.vg.kernel.org/pub/linux/kernel/people/gregkh/usb/2.4/usb-hid-2.4.25-pre7.patch

UPS's made by MGE can be used with usbhid just fine, and by removing the
ignore quirk allows them to be used with HAL so they just work when plugged
in, without needing to be manually configured.

With the ignore quirk in place a user would have to configure NUT before the
UPS could be used, as NUT uses it's own internal USB matching framework
to match against the USB devices, do low level control messages on the
device and then parse the HID tables all in userspace.

This is not needed, as allowing the device to be claimed as a usbhid device
allows it to be used like any other USB UPS device. The devices correctly
advertise the power device page which can be queried for the device state.

I assume the quirk was changed so that people using < libusb 0.1.8 could
still use NUT's internal HID code to manage the UPS.
libusb 0.1.8 was released quite some time ago: 2004-02-11.

This patch does not break NUT as in drivers/libusb.c the device is force
unbound from the kernel driver using usb_detach_kernel_driver_np () where
it can be controlled like normal.

[jkosina@suse.cz: adapt to the new hidbus code]
Signed-off-by: NRichard Hughes <rhughes@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Introduce a list of devices for which there is need to
force a creation of the hiddev interface, but still they
are operated by generic driver (i.e. certain UPS).
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Merge the logitech force feedback processing directly into logitech
driver from the usbhid core.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Move the handling of the leds resetting from the core to
the dell and logitech drivers.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Move connecting from usbhid to the hid layer and fix also hidp in
that manner.
This removes all the ignore/force hidinput/hiddev connecting quirks.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Remove support for both dynamic and static report descriptor
quirks. There is no longer rdesc code which it would support,
so it's useless.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Remove the file since these is no user now.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Move them from the core code to a separate driver.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>