Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 19 4月, 2014 1 次提交
  3. 18 4月, 2014 12 次提交
    • L
      Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip · 87a54cae
      由 Linus Torvalds 提交于 
      Pull timer fixes from Thomas Gleixner:
 "Viresh unearthed the following three hickups in the timer/timekeeping
  code:

   - Negated check for the result of a clock event selection

   - A missing early exit in the jiffies update path which causes
     update_wall_time to be called for nothing causing lock contention
     and wasted cycles in the timer interrupt

   - Checking a variable in the NOHZ code enable code for true which can
     only be set by that very code after the check succeeds.  That
     results in a rock solid runtime disablement of that feature"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick-sched: Check tick_nohz_enabled in tick_nohz_switch_to_nohz()
  tick-sched: Don't call update_wall_time() when delta is lesser than tick_period
  tick-common: Fix wrong check in tick_check_replacement()
      87a54cae
    • L
      Merge branch 'parisc-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux · 81cef0fe
      由 Linus Torvalds 提交于 
      Pull parisc updates from Helge Deller:
 "There are two major changes in this patchset:

  The major fix is that the epoll_pwait() syscall for 32bit userspace
  was not using the compat wrapper on a 64bit kernel.

  Secondly we changed the value of SHMLBA from 4MB to PAGE_SIZE to
  reflect that we can actually mmap to any multiple of PAGE_SIZE.  The
  only thing which needs care is that shared mmaps need to be mapped at
  the same offset inside the 4MB cache window"

* 'parisc-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: fix epoll_pwait syscall on compat kernel
  parisc: change value of SHMLBA from 0x00400000 to PAGE_SIZE
  parisc: Replace __get_cpu_var uses for address calculation
      81cef0fe
    • L
      Merge branch 'ipmi' (emailed ipmi fixes) · c2896def
      由 Linus Torvalds 提交于 
      Merge ipmi fixes from Corey Minyard:
 "Things collected since last kernel release.

  Some of these are pretty important.  The first three are bug fixes.
  The next two are to hopefully make everyone happy about allowing
  ACPI to be on all the time and not have IPMI have an effect on the
  system when not in use.  The last is a little cleanup"

* emailed patches from Corey Minyard <cminyard@mvista.com>:
  ipmi: boolify some things
  ipmi: Turn off all activity on an idle ipmi interface
  ipmi: Turn off default probing of interfaces
  ipmi: Reset the KCS timeout when starting error recovery
  ipmi: Fix a race restarting the timer
  Char: ipmi_bt_sm, fix infinite loop
      c2896def
    • C
      ipmi: boolify some things · 7aefac26
      由 Corey Minyard 提交于 
      Convert some ints to bools.
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      7aefac26
    • C
      ipmi: Turn off all activity on an idle ipmi interface · 89986496
      由 Corey Minyard 提交于 
      The IPMI driver would wake up periodically looking for events and
watchdog pretimeouts.  If there is nothing waiting for these events,
it's really kind of pointless to be checking for them.  So modify the
driver so the message handler can pass down if it needs the lower layer
to be waiting for these.  Modify the system interface lower layer to
turn off all timer and thread activity if the upper layer doesn't need
anything and it is not currently handling messages.  And modify the
message handler to not restart the timer if its timer is not needed.

The timers and kthread will still be enabled if:
 - the SI interface is handling a message.
 - a user has enabled watching for events.
 - the IPMI watchdog timer is in use (since it uses pretimeouts).
 - the message handler is waiting on a remote response.
 - a user has registered to receive commands.

This mostly affects interfaces without interrupts.  Interfaces with
interrupts already don't use CPU in the system interface when the
interface is idle.
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      89986496
    • C
      ipmi: Turn off default probing of interfaces · 0dfe6e7e
      由 Corey Minyard 提交于 
      The default probing can cause problems with some system, slow booting,
extra CPU usages, etc.  Turn it off by default and give a config option
to enable it.

From: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      0dfe6e7e
    • C
      ipmi: Reset the KCS timeout when starting error recovery · eb6d78ec
      由 Corey Minyard 提交于 
      The OBF timer in KCS was not reset in one situation when error recovery
was started, resulting in an immediate timeout.
Reported-by: NBodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      eb6d78ec
    • B
      ipmi: Fix a race restarting the timer · 48e8ac29
      由 Bodo Stroesser 提交于 
      With recent changes it is possible for the timer handler to detect an
idle interface and not start the timer, but the thread to start an
operation at the same time.  The thread will not start the timer in that
instance, resulting in the timer not running.

Instead, move all timer operations under the lock and start the timer in
the thread if it detect non-idle and the timer is not already running.
Moving under locks allows the last timeout to be set in both the thread
and the timer.  'Timer is not running' means that the timer is not
pending and smi_timeout() is not running.  So we need a flag to detect
this correctly.

Also fix a few other timeout bugs: setting the last timeout when the
interrupt has to be disabled and the timer started, and setting the last
timeout in check_start_timer_thread possibly racing with the timer
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Signed-off-by: NBodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      48e8ac29
    • J
      Char: ipmi_bt_sm, fix infinite loop · a94cdd1f
      由 Jiri Slaby 提交于 
      In read_all_bytes, we do

  unsigned char i;
  ...
  bt->read_data[0] = BMC2HOST;
  bt->read_count = bt->read_data[0];
  ...
  for (i = 1; i <= bt->read_count; i++)
    bt->read_data[i] = BMC2HOST;

If bt->read_data[0] == bt->read_count == 255, we loop infinitely in the
'for' loop.  Make 'i' an 'int' instead of 'char' to get rid of the
overflow and finish the loop after 255 iterations every time.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Reported-and-debugged-by: NRui Hui Dian <rhdian@novell.com>
Cc: Tomas Cech <tcech@suse.cz>
Cc: Corey Minyard <minyard@acm.org>
Cc: <openipmi-developer@lists.sourceforge.net>
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      a94cdd1f
    • L
      Merge tag 'stable/for-linus-3.15-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip · 88764e0a
      由 Linus Torvalds 提交于 
      Pull Xen fixes from David Vrabel:
 "Xen regression and bug fixes for 3.15-rc1:

   - fix completely broken 32-bit PV guests caused by x86 refactoring
     32-bit thread_info.
   - only enable ticketlock slow path on Xen (not bare metal)
   - fix two bugs with PV guests not shutting down when requested
   - fix a minor memory leak in xen-pciback error path"

* tag 'stable/for-linus-3.15-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/manage: Poweroff forcefully if user-space is not yet up.
  xen/xenbus: Avoid synchronous wait on XenBus stalling shutdown/restart.
  xen/spinlock: Don't enable them unconditionally.
  xen-pciback: silence an unwanted debug printk
  xen: fix memory leak in __xen_pcibk_add_pci_dev()
  x86/xen: Fix 32-bit PV guests's usage of kernel_stack
      88764e0a
    • L
      Merge tag '3.15-fixes' of git://neil.brown.name/md · 23c1a60e
      由 Linus Torvalds 提交于 
      Pull md bugfix from Neil Brown:
 "One BUG fix for md for recent commit"

* tag '3.15-fixes' of git://neil.brown.name/md:
  raid5: fix a race of stripe count check
      23c1a60e
    • L
      Merge tag 'fbdev-reorder-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux · 09df694a
      由 Linus Torvalds 提交于 
      Pull fbdev renaming patches from Tomi Valkeinen:
 "Reorder drivers/video/ directory so that all fbdev drivers are now
  located in drivers/video/fbdev/ and the fbdev framework core files are
  located in drivers/video/fbdev/core/

  The drivers/video/Kconfig is modified so that the DRM and the fbdev
  menu options are in separate submenus, instead of both being mixed in
  the same 'Graphics support' menu level"

* tag 'fbdev-reorder-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
  video: Kconfig: move drm and fb into separate menus
  fbdev: move fbdev core files to separate directory
  video: move fbdev to drivers/video/fbdev
      09df694a
  5. 17 4月, 2014 15 次提交
  7. 16 4月, 2014 12 次提交
    • I
      x86: Remove the PCI reboot method from the default chain · 5be44a6f
      由 Ingo Molnar 提交于 
      Steve reported a reboot hang and bisected it back to this commit:

  a4f1987e x86, reboot: Add EFI and CF9 reboot methods into the default list

He heroically tested all reboot methods and found the following:

  reboot=t       # triple fault                  ok
  reboot=k       # keyboard ctrl                 FAIL
  reboot=b       # BIOS                          ok
  reboot=a       # ACPI                          FAIL
  reboot=e       # EFI                           FAIL   [system has no EFI]
  reboot=p       # PCI 0xcf9                     FAIL

And I think it's pretty obvious that we should only try PCI 0xcf9 as a
last resort - if at all.

The other observation is that (on this box) we should never try
the PCI reboot method, but close with either the 'triple fault'
or the 'BIOS' (terminal!) reboot methods.

Thirdly, CF9_COND is a total misnomer - it should be something like
CF9_SAFE or CF9_CAREFUL, and 'CF9' should be 'CF9_FORCE' ...

So this patch fixes the worst problems:

 - it orders the actual reboot logic to follow the reboot ordering
   pattern - it was in a pretty random order before for no good
   reason.

 - it fixes the CF9 misnomers and uses BOOT_CF9_FORCE and
   BOOT_CF9_SAFE flags to make the code more obvious.

 - it tries the BIOS reboot method before the PCI reboot method.
   (Since 'BIOS' is a terminal reboot method resulting in a hang
    if it does not work, this is essentially equivalent to removing
    the PCI reboot method from the default reboot chain.)

 - just for the miraculous possibility of terminal (resulting
   in hang) reboot methods of triple fault or BIOS returning
   without having done their job, there's an ordering between
   them as well.
Reported-and-bisected-and-tested-by: NSteven Rostedt <rostedt@goodmis.org>
Cc: Li Aubrey <aubrey.li@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Link: http://lkml.kernel.org/r/20140404064120.GB11877@gmail.comSigned-off-by: NIngo Molnar <mingo@kernel.org>
      5be44a6f
    • L
      Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net · 10ec34fc
      由 Linus Torvalds 提交于 
      Pull networking fixes from David Miller:

 1) Fix BPF filter validation of netlink attribute accesses, from
    Mathias Kruase.

 2) Netfilter conntrack generation seqcount not initialized properly,
    from Andrey Vagin.

 3) Fix comparison mask computation on big-endian in nft_cmp_fast(),
    from Patrick McHardy.

 4) Properly limit MTU over ipv6, from Eric Dumazet.

 5) Fix seccomp system call argument population on 32-bit, from Daniel
    Borkmann.

 6) skb_network_protocol() should not use hard-coded ETH_HLEN, instead
    skb->mac_len needs to be used.  From Vlad Yasevich.

 7) We have several cases of using socket based communications to
    implement a tunnel.  For example, some tunnels are encapsulations
    over UDP so we use an internal kernel UDP socket to do the
    transmits.

    These tunnels should behave just like other software devices and
    pass the packets on down to the next layer.

    Most importantly we want the top-level socket (eg TCP) that created
    the traffic to be charged for the SKB memory.

    However, once you get into the IP output path, we have code that
    assumed that whatever was attached to skb->sk is an IP socket.

    To keep the top-level socket being charged for the SKB memory,
    whilst satisfying the needs of the IP output path, we now pass in an
    explicit 'sk' argument.

    From Eric Dumazet.

 8) ping_init_sock() leaks group info, from Xiaoming Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
  cxgb4: use the correct max size for firmware flash
  qlcnic: Fix MSI-X initialization code
  ip6_gre: don't allow to remove the fb_tunnel_dev
  ipv4: add a sock pointer to dst->output() path.
  ipv4: add a sock pointer to ip_queue_xmit()
  driver/net: cosa driver uses udelay incorrectly
  at86rf230: fix __at86rf230_read_subreg function
  at86rf230: remove check if AVDD settled
  net: cadence: Add architecture dependencies
  net: Start with correct mac_len in skb_network_protocol
  Revert "net: sctp: Fix a_rwnd/rwnd management to reflect real state of the receiver's buffer"
  cxgb4: Save the correct mac addr for hw-loopback connections in the L2T
  net: filter: seccomp: fix wrong decoding of BPF_S_ANC_SECCOMP_LD_W
  seccomp: fix populating a0-a5 syscall args in 32-bit x86 BPF
  qlcnic: Do not disable SR-IOV when VFs are assigned to VMs
  qlcnic: Fix QLogic application/driver interface for virtual NIC configuration
  qlcnic: Fix PVID configuration on eSwitch port.
  qlcnic: Fix max ring count calculation
  qlcnic: Fix to send INIT_NIC_FUNC as first mailbox.
  qlcnic: Fix panic due to uninitialzed delayed_work struct in use.
  ...
      10ec34fc
    • S
      cxgb4: use the correct max size for firmware flash · 6f1d7210
      由 Steve Wise 提交于 
      The wrong max fw size was being used and causing false
"too big" errors running ethtool -f.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      6f1d7210
    • A
      qlcnic: Fix MSI-X initialization code · 8564ae09
      由 Alexander Gordeev 提交于 
      Function qlcnic_setup_tss_rss_intr() might enter endless
loop in case pci_enable_msix() contiguously returns a
positive number of MSI-Xs that could have been allocated.
Besides, the function contains 'err = -EIO;' assignment
that never could be reached. This update fixes the
aforementioned issues.

Cc: Shahed Shaikh <shahed.shaikh@qlogic.com>
Cc: Dept-HSGLinuxNICDev@qlogic.com
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Acked-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      8564ae09
    • N
      ip6_gre: don't allow to remove the fb_tunnel_dev · 54d63f78
      由 Nicolas Dichtel 提交于 
      It's possible to remove the FB tunnel with the command 'ip link del ip6gre0' but
this is unsafe, the module always supposes that this device exists. For example,
ip6gre_tunnel_lookup() may use it unconditionally.

Let's add a rtnl handler for dellink, which will never remove the FB tunnel (we
let ip6gre_destroy_tunnels() do the job).

Introduced by commit c12b395a ("gre: Support GRE over IPv6").

CC: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      54d63f78
    • V
      tick-sched: Check tick_nohz_enabled in tick_nohz_switch_to_nohz() · 27630532
      由 Viresh Kumar 提交于 
      Since commit d689fe22 (NOHZ: Check for nohz active instead of nohz
enabled) the tick_nohz_switch_to_nohz() function returns because it
checks for the tick_nohz_active flag. This can't be set, because the
function itself sets it.

Undo the change in tick_nohz_switch_to_nohz().
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Cc: linaro-kernel@lists.linaro.org
Cc: fweisbec@gmail.com
Cc: Arvind.Chauhan@arm.com
Cc: linaro-networking@linaro.org
Cc: <stable@vger.kernel.org> # 3.13+
Link: http://lkml.kernel.org/r/40939c05f2d65d781b92b20302b02243d0654224.1397537987.git.viresh.kumar@linaro.orgSigned-off-by: NThomas Gleixner <tglx@linutronix.de>
      27630532
    • V
      tick-sched: Don't call update_wall_time() when delta is lesser than tick_period · 03e6bdc5
      由 Viresh Kumar 提交于 
      In tick_do_update_jiffies64() we are processing ticks only if delta is
greater than tick_period. This is what we are supposed to do here and
it broke a bit with this patch:

commit 47a1b796 (tick/timekeeping: Call update_wall_time outside the
jiffies lock)

With above patch, we might end up calling update_wall_time() even if
delta is found to be smaller that tick_period. Fix this by returning
when the delta is less than tick period.

[ tglx: Made it a 3 liner and massaged changelog ]
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Cc: linaro-kernel@lists.linaro.org
Cc: fweisbec@gmail.com
Cc: Arvind.Chauhan@arm.com
Cc: linaro-networking@linaro.org
Cc: John Stultz <john.stultz@linaro.org>
Cc: <stable@vger.kernel.org> # v3.14+
Link: http://lkml.kernel.org/r/80afb18a494b0bd9710975bcc4de134ae323c74f.1397537987.git.viresh.kumar@linaro.orgSigned-off-by: NThomas Gleixner <tglx@linutronix.de>
      03e6bdc5
    • V
      tick-common: Fix wrong check in tick_check_replacement() · 521c4299
      由 Viresh Kumar 提交于 
      tick_check_replacement() returns if a replacement of clock_event_device is
possible or not. It does this as the first check:

	if (tick_check_percpu(curdev, newdev, smp_processor_id()))
		return false;

Thats wrong. tick_check_percpu() returns true when the device is
useable. Check for false instead.

[ tglx: Massaged changelog ]
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Cc: <stable@vger.kernel.org> # v3.11+
Cc: linaro-kernel@lists.linaro.org
Cc: fweisbec@gmail.com
Cc: Arvind.Chauhan@arm.com
Cc: linaro-networking@linaro.org
Link: http://lkml.kernel.org/r/486a02efe0246635aaba786e24b42d316438bf3b.1397537987.git.viresh.kumar@linaro.orgSigned-off-by: NThomas Gleixner <tglx@linutronix.de>
      521c4299
    • E
      ipv4: add a sock pointer to dst->output() path. · aad88724
      由 Eric Dumazet 提交于 
      In the dst->output() path for ipv4, the code assumes the skb it has to
transmit is attached to an inet socket, specifically via
ip_mc_output() : The sk_mc_loop() test triggers a WARN_ON() when the
provider of the packet is an AF_PACKET socket.

The dst->output() method gets an additional 'struct sock *sk'
parameter. This needs a cascade of changes so that this parameter can
be propagated from vxlan to final consumer.

Fixes: 8f646c92 ("vxlan: keep original skb ownership")
Reported-by: Nlucien xin <lucien.xin@gmail.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      aad88724
    • I
      Merge tag 'perf-urgent-for-mingo' of... · ad466db5
      由 Ingo Molnar 提交于 
      Merge tag 'perf-urgent-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/jolsa/perf into perf/urgent

Pull perf/urgent fixes from Jiri Olsa:

  * Instead of redirecting flex output, use -o (Cody P Schafer)

  * Fix double free in perf test 21 (Adrian Hunter)
Signed-off-by: NJiri Olsa <jolsa@redhat.com>
Signed-off-by: NIngo Molnar <mingo@kernel.org>
      ad466db5
    • E
      ipv4: add a sock pointer to ip_queue_xmit() · b0270e91
      由 Eric Dumazet 提交于 
      ip_queue_xmit() assumes the skb it has to transmit is attached to an
inet socket. Commit 31c70d59 ("l2tp: keep original skb ownership")
changed l2tp to not change skb ownership and thus broke this assumption.

One fix is to add a new 'struct sock *sk' parameter to ip_queue_xmit(),
so that we do not assume skb->sk points to the socket used by l2tp
tunnel.

Fixes: 31c70d59 ("l2tp: keep original skb ownership")
Reported-by: NZhan Jianyu <nasa4836@gmail.com>
Tested-by: NZhan Jianyu <nasa4836@gmail.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      b0270e91
    • K
      xen/manage: Poweroff forcefully if user-space is not yet up. · eb47f712
      由 Konrad Rzeszutek Wilk 提交于 
      The user can launch the guest in this sequence:

xl create -p /vm.cfg	[launch, but pause it]
xl shutdown latest	[sets control/shutdown=poweroff]
xl unpause latest
xl console latest	[and see that the guest has completely
ignored the shutdown request]

In reality the guest hasn't ignored it. It registers a watch
and gets a notification that there is value. It then calls
the shutdown_handler which ends up calling orderly_shutdown.

Unfortunately that is so early in the bootup that there
are no user-space. Which means that the orderly_shutdown fails.
But since the force flag was set to false it continues on without
reporting.

What we really want to is to use the force when we are in the
SYSTEM_BOOTING state and not use the 'force' when SYSTEM_RUNNING.

However, if we are in the running state - and the shutdown command
has been given before the user-space has been setup, there is nothing
we can do. Worst yet, we stop ignoring the 'xl shutdown' requests!

As such, the other part of this patch is to only stop ignoring
the 'xl shutdown' when we are truly in the power off sequence.

That means the user can do multiple 'xl shutdown' and we will try
to act on them instead of ignoring them.

Fixes-Bug: http://bugs.xenproject.org/xen/bug/6Reported-by: NAlex Bligh <alex@alex.org.uk>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
      eb47f712