This change renames the fwd_priv member to accel_priv as this more
accurately reflects the actual purpose of this value. In addition I am
adding an accessor which will allow us to further abstract this in the
future if needed.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Drop the code for handling macvlan specific unicast lists. It isn't needed
since we don't take any efforts to maintain it when we bring the interface
up and it takes the slow path anyway.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

For the MAC read operation, the device can return up to two (LAN and WoL)
MAC addresses. Without access to adequate memory, the device will return
an error. Fixed this by allocating the right amount of memory. Also, logic
to detect and copy the LAN MAC address into the port_info structure has
been added. Note that the WoL MAC address is ignored currently as the WoL
feature isn't supported yet.

Fixes: dc49c772 ("ice: Get MAC/PHY/link info and scheduler topology")
Signed-off-by: NMd Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

According to the hardware spec, checking the INTEVENT bit isn't a
reliable way to detect if an OICR interrupt has occurred. This is
because this bit can be cleared by the hardware/firmware before the
interrupt service routine has run. So instead, just check for OICR
events every time.

Fixes: 940b61af ("ice: Initialize PF and setup miscellaneous interrupt")
Signed-off-by: NBen Shelton <benjamin.h.shelton@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Action type 5 defines large action generic values. Fix comment to
reflect that better.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ice_sched_add_nodes_to_layer is used recursively, and so we start
with num_nodes_added being 0. This way, in case of an error or if
num_nodes is NULL, the function just returns 0 to indicate that no
nodes were added.

Fixes: 5513b920 ("ice: Update Tx scheduler tree for VSI multi-Tx queue support")
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When Qav mode is enabled, queue 0 should be kept on Stream Reservation
mode. From the i210 datasheet, section 8.12.19:

"Note: Queue0 QueueMode must be set to 1b when TransmitMode is set to
Qav." ("QueueMode 1b" represents the Stream Reservation mode)

The solution is to give queue 0 the all the credits it might need, so
it has priority over queue 1.

A situation where this can happen is when cbs is "installed" only on
queue 1, leaving queue 0 alone. For example:

$ tc qdisc replace dev enp2s0 handle 100: parent root mqprio num_tc 3 \
     	   map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@2 hw 0

$ tc qdisc replace dev enp2s0 parent 100:2 cbs locredit -1470 \
     	   hicredit 30 sendslope -980000 idleslope 20000 offload 1
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The current error handling for failed resource setup for xdp_ring
data is a break out of the loop and returning 0 indicated everything
was OK, when in fact it is not.  Fix this by exiting via the
error exit label err_setup_tx that will clean up the resources
correctly and return and error status.

Detected by CoverityScan, CID#1466879 ("Logically dead code")

Fixes: 21092e9c ("ixgbevf: Add support for XDP_TX action")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Changing API ndo_xdp_xmit to take a struct xdp_frame instead of struct
xdp_buff.  This brings xdp_return_frame and ndp_xdp_xmit in sync.

This builds towards changing the API further to become a bulk API,
because xdp_buff is not a queue-able object while xdp_frame is.

V4: Adjust for commit 59655a5b ("tuntap: XDP_TX can use native XDP")
V7: Adjust for commit d9314c47 ("i40e: add support for XDP_REDIRECT")
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changing API xdp_return_frame() to take struct xdp_frame as argument,
seems like a natural choice. But there are some subtle performance
details here that needs extra care, which is a deliberate choice.

When de-referencing xdp_frame on a remote CPU during DMA-TX
completion, result in the cache-line is change to "Shared"
state. Later when the page is reused for RX, then this xdp_frame
cache-line is written, which change the state to "Modified".

This situation already happens (naturally) for, virtio_net, tun and
cpumap as the xdp_frame pointer is the queued object.  In tun and
cpumap, the ptr_ring is used for efficiently transferring cache-lines
(with pointers) between CPUs. Thus, the only option is to
de-referencing xdp_frame.

It is only the ixgbe driver that had an optimization, in which it can
avoid doing the de-reference of xdp_frame.  The driver already have
TX-ring queue, which (in case of remote DMA-TX completion) have to be
transferred between CPUs anyhow.  In this data area, we stored a
struct xdp_mem_info and a data pointer, which allowed us to avoid
de-referencing xdp_frame.

To compensate for this, a prefetchw is used for telling the cache
coherency protocol about our access pattern.  My benchmarks show that
this prefetchw is enough to compensate the ixgbe driver.

V7: Adjust for commit d9314c47 ("i40e: add support for XDP_REDIRECT")
V8: Adjust for commit bd658dda ("net/mlx5e: Separate dma base address
and offset in dma_sync call")
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the IDA infrastructure for getting a cyclic increasing ID number,
that is used for keeping track of each registered allocator per
RX-queue xdp_rxq_info.  Instead of using the IDR infrastructure, which
uses a radix tree, use a dynamic rhashtable, for creating ID to
pointer lookup table, because this is faster.

The problem that is being solved here is that, the xdp_rxq_info
pointer (stored in xdp_buff) cannot be used directly, as the
guaranteed lifetime is too short.  The info is needed on a
(potentially) remote CPU during DMA-TX completion time . In an
xdp_frame the xdp_mem_info is stored, when it got converted from an
xdp_buff, which is sufficient for the simple page refcnt based recycle
schemes.

For more advanced allocators there is a need to store a pointer to the
registered allocator.  Thus, there is a need to guard the lifetime or
validity of the allocator pointer, which is done through this
rhashtable ID map to pointer. The removal and validity of of the
allocator and helper struct xdp_mem_allocator is guarded by RCU.  The
allocator will be created by the driver, and registered with
xdp_rxq_info_reg_mem_model().

It is up-to debate who is responsible for freeing the allocator
pointer or invoking the allocator destructor function.  In any case,
this must happen via RCU freeing.

Use the IDA infrastructure for getting a cyclic increasing ID number,
that is used for keeping track of each registered allocator per
RX-queue xdp_rxq_info.

V4: Per req of Jason Wang
- Use xdp_rxq_info_reg_mem_model() in all drivers implementing
  XDP_REDIRECT, even-though it's not strictly necessary when
  allocator==NULL for type MEM_TYPE_PAGE_SHARED (given it's zero).

V6: Per req of Alex Duyck
- Introduce rhashtable_lookup() call in later patch

V8: Address sparse should be static warnings (from kbuild test robot)
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also convert driver i40e, which very recently got XDP_REDIRECT support
in commit d9314c47 ("i40e: add support for XDP_REDIRECT").

V7: This patch got added in V7 of this patchset.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend struct ixgbe_tx_buffer to store the xdp_mem_info.

Notice that this could be optimized further by putting this into
a union in the struct ixgbe_tx_buffer, but this patchset
works towards removing this again.  Thus, this is not done.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1) Return correct size from ice_get_regs_len.
2) Fix incorrect use of ARRAY_SIZE in ice_get_regs.

Fixes: fcea6f3d (ice: Add stats and ethtool support)
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix to return error code ICE_ERR_NO_MEMORY from the alloc error
handling case instead of 0, as done elsewhere in this function.

Fixes: dc49c772 ("ice: Get MAC/PHY/link info and scheduler topology")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Acked-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Previously the driver used pcie_get_minimum_link() to warn when the NIC
is in a slot that can't supply as much bandwidth as the NIC could use.

pcie_get_minimum_link() can be misleading because it finds the slowest link
and the narrowest link (which may be different links) without considering
the total bandwidth of each link.  For a path with a 16 GT/s x1 link and a
2.5 GT/s x16 link, it returns 2.5 GT/s x1, which corresponds to 250 MB/s of
bandwidth, not the true available bandwidth of about 1969 MB/s for a
16 GT/s x1 link.

Use pcie_print_link_status() to report PCIe link speed and possible
limitations instead of implementing this in the driver itself.  This finds
the slowest link in the path to the device by computing the total bandwidth
of each link and compares that with the capabilities of the device.

Note that the driver previously used dev_warn() to suggest using a
different slot, but pcie_print_link_status() uses dev_info() because if the
platform has no faster slot available, the user can't do anything about the
warning and may not want to be bothered with it.
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NJacob Keller <jacob.e.keller@intel.com>

The driver now acts upon the XDP_REDIRECT return action. Two new ndos
are implemented, ndo_xdp_xmit and ndo_xdp_flush.

XDP_REDIRECT action enables XDP program to redirect frames to other
netdevs.
Signed-off-by: NBjörn Töpel <bjorn.topel@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This commit tweaks the page counting for XDP_REDIRECT to function
properly. XDP_REDIRECT support will be added in a future commit.

The current page counting scheme assumes that the reference count
cannot decrease until the received frame is sent to the upper layers
of the networking stack. This assumption does not hold for the
XDP_REDIRECT action, since a page (pointed out by xdp_buff) can have
its reference count decreased via the xdp_do_redirect call.

To work around that, we now start off by a large page count and then
don't allow a refcount less than two.
Signed-off-by: NBjörn Töpel <bjorn.topel@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove the gaps created by the recent refactor of various feature flags
that have moved to the state field. Use only a u32 now that we have
fewer than 32 flags in the field.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Now that the only places which modify flags are either (a) during
initialization prior to creating a netdevice, or (b) while holding the
rtnl lock, we no longer need the cmpxchg64 call in i40e_set_priv_flags.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When we suspend and resume, we need to clear and re-enable the interrupt
scheme. This was previously not done while holding the RTNL lock, which
could be problematic, because we are actually destroying and re-creating
queues.

Hold the RTNL lock for the entire sequence of preparing for reset, and
when resuming. This additionally protects the flags related to interrupt
scheme under RTNL lock so that their modification is properly threaded.

This is part of a larger effort to remove the need for cmpxchg64 in
i40e_set_priv_flags().
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The iWarp client flags are all potentially changed when the RTNL lock is
not held, so they should not be part of the pf->flags variable. Instead,
move them into the state field so that we can use atomic bit operations.

This is part of a larger effort to remove cmpxchg64 in
i40e_set_priv_flags()
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This flag is modified outside of the RTNL lock and thus should not be
part of the pf->flags variable.

Use a state bit instead, so that we can use atomic bit operations.

This is part of a larger effort to remove cmpxchg64 in
i40e_set_priv_flags()
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The two Flow Directory auto disable flags are used at run time to mark
when the flow director features needed to be disabled. Thus the flags
could change even when the RTNL lock is not held.

They also have some code constructions which really should be
test_and_set or test_and_clear using atomic bit operations.

Create new state fields to mark this, and stop including them in
pf->flags.

This is part of a larger effort to remove the need for cmpxchg64 in
i40e_set_priv_flags().
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This flag is modified during run time, possibly even when the RTNL lock
is not held. Additionally it has a few places which should be using
test_and_set or test_and_clear atomic bit operations.

Create a new state bit __I40E_UDP_SYNC_PENDING and use it instead of the
ole I40E_FLAG_UDP_FILTER_SYNC flag.

This is part of a larger effort to remove the need for using cmpxchg64
in i40e_set_priv_flags.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The I40E_FLAG_FILTER_SYNC flag is modified during run time possibly when
the RTNL lock is not held. Thus, it should not be part of pf->flags, and
instead should be using atomic bit operations in the pf->state field.

Create a __I40E_MACVLAN_SYNC_PENDING state bit, and use it instead of
the old I40E_FLAG_FILTER_SYNC flag.

This is part of a larger effort to remove the need for cmpxchg64 in
i40e_set_priv_flags().
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch implements multiple pieces of functionality:

1. Added ice_vsi_sync_filters, which is called through the service task
   to push filter updates to the hardware.

2. Add support to enable/disable promiscuous mode on an interface.
   Enabling/disabling promiscuous mode on an interface results in
   addition/removal of a promisc filter rule through ice_vsi_sync_filters.

3. Implement handlers for ndo_set_mac_address, ndo_change_mtu,
   ndo_poll_controller and ndo_set_rx_mode.

This patch also marks the end of the driver addition by bumping up the
driver version.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Link events are posted to a PF's admin receive queue (ARQ). This patch
adds the ability to detect and process link events.

This patch also adds the ability to process resets.

The driver can process the following resets:
    1) EMP Reset (EMPR)
    2) Global Reset (GLOBR)
    3) Core Reset (CORER)
    4) Physical Function Reset (PFR)

EMPR is the largest level of reset that the driver can handle. An EMPR
resets the manageability block and also the data path, including PHY and
link for all the PFs. The affected PFs are notified of this event through
a miscellaneous interrupt.

GLOBR is a subset of EMPR. It does everything EMPR does except that it
doesn't reset the manageability block.

CORER is a subset of GLOBR. It does everything GLOBR does but doesn't
reset PHY and link.

PFR is a subset of CORER and affects only the given physical function.
In other words, PFR can be thought of as a CORER for a single PF. Since
only the issuing PF is affected, a PFR doesn't result in the miscellaneous
interrupt being triggered.

All the resets have the following in common:
1) Tx/Rx is halted and all queues are stopped.
2) All the VSIs and filters programmed for the PF are lost and have to be
   reprogrammed.
3) Control queue interfaces are reset and have to be reprogrammed.

In the rebuild flow, control queues are reinitialized, VSIs are reallocated
and filters are restored.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds the ability for a VSI to use multiple Tx queues. More
specifically, the patch
    1) Provides the ability to update the Tx scheduler tree in the
       firmware. The driver can configure the Tx scheduler tree by
       adding/removing multiple Tx queues per TC per VSI.

    2) Allows a VSI to reconfigure its Tx queues during runtime.

    3) Synchronizes the Tx scheduler update operations using locks.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch implements a watchdog task to get packet statistics from
the device.

This patch also adds support for the following ethtool operations:

ethtool devname
ethtool -s devname [msglvl N] [msglevel type on|off]
ethtool -g|--show-ring devname
ethtool -G|--set-ring devname [rx N] [tx N]
ethtool -i|--driver devname
ethtool -d|--register-dump devname [raw on|off] [hex on|off] [file name]
ethtool -k|--show-features|--show-offload devname
ethtool -K|--features|--offload devname feature on|off
ethtool -P|--show-permaddr devname
ethtool -S|--statistics devname
ethtool -a|--show-pause devname
ethtool -A|--pause devname [autoneg on|off] [rx on|off] [tx on|off]
ethtool -r|--negotiate devname

CC: Andrew Lunn <andrew@lunn.ch>
CC: Jakub Kicinski <kubakici@wp.pl>
CC: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: NStephen Hemminger <stephen@networkplumber.org>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for VLANs. When a VLAN is created a switch filter
is added to direct the VLAN traffic to the corresponding VSI. When a VLAN
is deleted, the filter is deleted as well.

This patch also adds support for the following hardware offloads.
    1) VLAN tag insertion/stripping
    2) Receive Side Scaling (RSS)
    3) Tx checksum and TCP segmentation
    4) Rx checksum
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch implements ice_start_xmit (the handler for ndo_start_xmit) and
related functions. ice_start_xmit ultimately calls ice_tx_map, where the
Tx descriptor is built and posted to the hardware by bumping the ring tail.

This patch also implements ice_napi_poll, which is invoked when there's an
interrupt on the VSI's queues. The interrupt can be due to either a
completed Tx or an Rx event. In case of a completed Tx/Rx event, resources
are reclaimed. Additionally, in case of an Rx event, the skb is fetched
and passed up to the network stack.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch configures the VSIs to be able to send and receive
packets by doing the following:

1) Initialize flexible parser to extract and include certain
   fields in the Rx descriptor.

2) Add Tx queues by programming the Tx queue context (implemented in
   ice_vsi_cfg_txqs). Note that adding the queues also enables (starts)
   the queues.

3) Add Rx queues by programming Rx queue context (implemented in
   ice_vsi_cfg_rxqs). Note that this only adds queues but doesn't start
   them. The rings will be started by calling ice_vsi_start_rx_rings on
   interface up.

4) Configure interrupts for VSI queues.

5) Implement ice_open and ice_stop.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A VSI needs traffic directed towards it. This is done by programming
filter rules on the switch (embedded vSwitch) element in the hardware,
which connects the VSI to the ingress/egress port.

This patch introduces data structures and functions necessary to add
remove or update switch rules on the switch element. This is a pretty low
level function that is generic enough to add a whole range of filters.

This patch also introduces two top level functions ice_add_mac and
ice_remove mac which through a series of intermediate helper functions
eventually call ice_aq_sw_rules to add/delete simple MAC based filters.
It's worth noting that one invocation of ice_add_mac/ice_remove_mac
is capable of adding/deleting multiple MAC filters.

Also worth noting is the fact that the driver maintains a list of currently
active filters, so every filter addition/removal causes an update to this
list. This is done for a couple of reasons:

1) If two VSIs try to add the same filters, we need to detect it and do
   things a little differently (i.e. use VSI lists, described below) as
   the same filter can't be added more than once.

2) In the event of a hardware reset we can simply walk through this list
   and restore the filters.

VSI Lists:
In a multi-VSI situation, it's possible that multiple VSIs want to add the
same filter rule. For example, two VSIs that want to receive broadcast
traffic would both add a filter for destination MAC ff:ff:ff:ff:ff:ff.
This can become cumbersome to maintain and so this is handled using a
VSI list.

A VSI list is resource that can be allocated in the hardware using the
ice_aq_alloc_free_res admin queue command. Simply put, a VSI list can
be thought of as a subscription list containing a set of VSIs to which
the packet should be forwarded, should the filter match.

For example, if VSI-0 has already added a broadcast filter, and VSI-1
wants to do the same thing, the filter creation flow will detect this,
allocate a VSI list and update the switch rule so that broadcast traffic
will now be forwarded to the VSI list which contains VSI-0 and VSI-1.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch introduces data structures and functions to alloc/free
VSIs. The driver represents a VSI using the ice_vsi structure.

Some noteworthy points about VSI allocation:

1) A VSI is allocated in the firmware using the "add VSI" admin queue
   command (implemented as ice_aq_add_vsi). The firmware returns an
   identifier for the allocated VSI. The VSI context is used to program
   certain aspects (loopback, queue map, etc.) of the VSI's configuration.

2) A VSI is deleted using the "free VSI" admin queue command (implemented
   as ice_aq_free_vsi).

3) The driver represents a VSI using struct ice_vsi. This is allocated
   and initialized as part of the ice_vsi_alloc flow, and deallocated
   as part of the ice_vsi_delete flow.

4) Once the VSI is created, a netdev is allocated and associated with it.
   The VSI's ring and vector related data structures are also allocated
   and initialized.

5) A VSI's queues can either be contiguous or scattered. To do this, the
   driver maintains a bitmap (vsi->avail_txqs) which is kept in sync with
   the firmware's VSI queue allocation imap. If the VSI can't get a
   contiguous queue allocation, it will fallback to scatter. This is
   implemented in ice_vsi_get_qs which is called as part of the VSI setup
   flow. In the release flow, the VSI's queues are released and the bitmap
   is updated to reflect this by ice_vsi_put_qs.

CC: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch continues the initialization flow as follows:

1) Allocate and initialize necessary fields (like vsi, num_alloc_vsi,
   irq_tracker, etc) in the ice_pf instance.

2) Setup the miscellaneous interrupt handler. This also known as the
   "other interrupt causes" (OIC) handler and is used to handle non
   hotpath interrupts (like control queue events, link events,
   exceptions, etc.

3) Implement a background task to process admin queue receive (ARQ)
   events received by the driver.

CC: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds code to continue the initialization flow as follows:

1) Get PHY/link information and store it
2) Get default scheduler tree topology and store it
3) Get the MAC address associated with the port and store it
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds to the initialization flow by getting switch
configuration, scheduler configuration and device capabilities.

Switch configuration:
On boot, an L2 switch element is created in the firmware per physical
function. Each physical function is also mapped to a port, to which its
switch element is connected. In other words, this switch can be visualized
as an embedded vSwitch that can connect a physical function's virtual
station interfaces (VSIs) to the egress/ingress port. Egress/ingress
filters will be eventually created and applied on this switch element.
As part of the initialization flow, the driver gets configuration data
from this switch element and stores it.

Scheduler configuration:
The Tx scheduler is a subsystem responsible for setting and enforcing QoS.
As part of the initialization flow, the driver queries and stores the
default scheduler configuration for the given physical function.

Device capabilities:
As part of initialization, the driver has to determine what the device is
capable of (ex. max queues, VSIs, etc). This information is obtained from
the firmware and stored by the driver.

CC: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch implements multiple pieces of the initialization flow
as follows:

1) A reset is issued to ensure a clean device state, followed
   by initialization of admin queue interface.

2) Once the admin queue interface is up, clear the PF config
   and transition the device to non-PXE mode.

3) Get the NVM configuration stored in the device's non-volatile
   memory (NVM) using ice_init_nvm.

CC: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A control queue is a hardware interface which is used by the driver
to interact with other subsystems (like firmware, PHY, etc.). It is
implemented as a producer-consumer ring. More specifically, an
"admin queue" is a type of control queue used to interact with the
firmware.

This patch introduces data structures and functions to initialize
and teardown control/admin queues. Once the admin queue is initialized,
the driver uses it to get the firmware version.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>