Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 06 10月, 2011 8 次提交
    • K
      drm/i915: edp_panel_on does not need to return a bool · 7d639f35
      由 Keith Packard 提交于 
      The return value was unused, so just stop doing that.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      7d639f35
    • K
      drm/i915: Move eDP panel fixed mode from dev_priv to intel_dp · d15456de
      由 Keith Packard 提交于 
      This value doesn't come directly from the VBT, and so is rather
specific to the particular DP output.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      d15456de
    • K
      drm/i915: Correct eDP panel power sequencing delay computations · f01eca2e
      由 Keith Packard 提交于 
      Store the panel power sequencing delays in the dp private structure,
rather than the global device structure. Who knows, maybe we'll get
more than one eDP device in the future.

From the eDP spec, we need the following numbers:

 T1 + T3	Power on to Aux Channel operation (panel_power_up_delay)

		This marks how long it takes the panel to boot up and
		get ready to receive aux channel communications.

 T8		Video signal to backlight on (backlight_on_delay)

		Once a valid video signal is being sent to the device,
		it can take a while before the panel is actuall
		showing useful data. This delay allows the panel
		to get something reasonable up before the backlight
		is turned on.

 T9		Backlight off to video off (backlight_off_delay)

		Turning the backlight off can take a moment, so
		this delay makes sure there is still valid video
		data on the screen.

 T10		Video off to power off (panel_power_down_delay)

		Presumably this delay allows the panel to perform
		an orderly shutdown of the display.

 T11 + T12	Power off to power on (panel_power_cycle_delay)

		So, once you turn the panel off, you have to wait a
		while before you can turn it back on. This delay is
		usually the longest in the entire sequence.

Neither the VBIOS source code nor the hardware documentation has a
clear mapping between the delay values they provide and those required
by the eDP spec. The VBIOS code actually uses two different labels for
the delay values in the five words of the relevant VBT table.

**** MORE LATER ***

Look at both the current hardware register settings and the VBT
specified panel power sequencing timings. Use the maximum of the two
delays, to make sure things work reliably. If there is no VBT data,
then those values will be initialized to zero, so we'll just use the
values as programmed in the hardware. Note that the BIOS just fetches
delays from the VBT table to place in the hardware registers, so we
should get the same values from both places, except for rounding.

VBT doesn't provide any values for T1 or T2, so we'll always just use
the hardware value for that.

The panel power up delay is thus T1 + T2 + T3, which should be
sufficient in all cases.

The panel power down delay is T1 + T2 + T12, using T1+T2 as a proxy
for T11, which isn't available anywhere.

For the backlight delays, the eDP spec says T6 + T8 is the delay from the
end of link training to backlight on and T9 is the delay from
backlight off until video off. The hardware provides a 'backlight on'
delay, which I'm taking to be T6 + T8 while the VBT provides something
called 'T7', which I'm assuming is s

On the macbook air I'm testing with, this yields a power-up delay of
over 200ms and a power-down delay of over 600ms. It all works now, but
we're frobbing these power controls several times during mode setting,
making the whole process take an awfully long time.
Signed-off-by: NKeith Packard <keithp@keithp.com>
      f01eca2e
    • K
      drm/i915: Ensure eDP powered up during DP_SET_POWER operation in dp_prepare · f58ff854
      由 Keith Packard 提交于 
      Any call to intel_dp_sink_dpms must ensure that the panel has power so
that the DP_SET_POWER operation will be correctly received. The only
one missing this was in intel_dp_prepare.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      f58ff854
    • K
      drm/i915: Enable eDP panel power during I2C initialization sequence · 0b5c541b
      由 Keith Packard 提交于 
      The DP i2c initialization code does a couple of i2c transactions,
which means that an eDP panel must be powered up.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      0b5c541b
    • K
      drm/i915: Wrap DP EDID fetch functions to enable eDP panel power · 8c241fef
      由 Keith Packard 提交于 
      Talking to the eDP DDC channel requires that the panel be powered
up. Wrap both the EDID and modes fetch code with calls to turn the vdd
power on and back off.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      8c241fef
    • K
      drm/i915: Delay DP i2c initialization until panel power timings are computed · 552fb0b7
      由 Keith Packard 提交于 
      On eDP, DDC requires panel power, but turning that on uses the panel
power sequencing timing values fetch from the DPCD data.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      552fb0b7
    • K
      drm/i915: Ensure panel is on during DPMS off · 245e2708
      由 Keith Packard 提交于 
      If the panel is already off, we'll need to turn VDD on to execute the
(useless) DPMS off code. Yes, it would be better to just not do any of
this, but correctness, and *then* performance.
Signed-off-by: NKeith Packard <keithp@keithp.com>
      245e2708
  3. 01 10月, 2011 7 次提交
  5. 22 9月, 2011 2 次提交
  7. 20 9月, 2011 1 次提交
  9. 09 9月, 2011 6 次提交
  11. 06 9月, 2011 1 次提交
  13. 02 9月, 2011 1 次提交
  15. 31 8月, 2011 1 次提交
  17. 30 8月, 2011 2 次提交
  19. 29 8月, 2011 1 次提交
  21. 26 8月, 2011 1 次提交
  23. 23 8月, 2011 5 次提交
  25. 22 8月, 2011 4 次提交