With runtime power save feature enabled, Headphone hotplug
event will not be detected while controller/codec in D3. HDA has
feature WAKEEN to let codec wake up system if controller is in D3 or
system in S3.(HDA Spec 4.5.9.2/3). Codec can send out INT or wake up
controller depending on whether CIE or GIE enabled.(Figure 4, Interupt
structure).

The controller must be in RESET mode after enter runtime-suspend, otherwise
it will not be waken up even if codec send out wake-up event. And STATESTS
will be cleared after controller brought out of RESET mode.

This patch only enable WAKEEN for runtime-suspend(Controller D3) mode,
not for system S3 mode. with tool "evtest", Headphone hotplug events
could be cought and reported successfully.

[fixed an unused variable warning by tiwai]
Signed-off-by: NWang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

With jackpoll_interval != 0, it's used to poll jack event periodically
in a delayed work. if it's 0, give the caller chance to probe jack status
but will not restart the delayed work.

In the next patch which enable WAKEEN feature, HDA controller was able to wake
up system when it's in D3, it's useful to detect Jack hotplug event and notify
userspace. By default the jackpoll_interval=0, this patch let jack poll once
without starting the delayed work.
Signed-off-by: NWang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Clearing jackpoll_interval before calling cancel_delayed_work_sync(),
otherwise the work will be triggered again and cause impact in
hda_jackpoll_work(). The next patch will poll jack once even with
jackpoll_interval=0.
Signed-off-by: NWang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The test here is always true because S[i].urb is an array not a pointer.
Also it's bogus because the intent was to test:
	if (S->urb[i]) {
instead of:
	if (S[i].urb) {

Anyway, usb_kill_urb() and usb_free_urb() accept NULL pointers so we can
just remove this.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Register STATESTS is 16-bit length, use correct API for read/write.
Signed-off-by: NWang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When the power state of ALC283 codec goes to D3, it gives a noise via
headphone output.  This is because the driver tries to clear all pins
via snd_hda_shutup_pins().  Setting the mic pin to zero triggers such
a noise.

Define a new shutup call specific to this codec and control the pins
there more precisely.  Also, add the power-save enable/disable
sequences in the resume and the new shutup calls.
Signed-off-by: NKailang Yang <kailang@realtek.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Instead of calling snd_hda_shutup_pins() unconditionally, allow it be
called in spec->shutup callback.  In this way, we can avoid calling
this function if it causes a problem like we see in the next patch
following this.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The usage of strict_strto*() is not preferred, because
strict_strto*() is obsolete. Thus, kstrto*() should be
used.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

snd_hda_jack_detect() function returns a boolean value for a jack
plugged in or not, but it also returns always true when the
corresponding pin is phantom (i.e. fixed).  This is OK in most cases,
but it makes the generic parser misbehaving about the auto-mute or
auto-mic switching, e.g. when one of headphone pins is a fixed.
Namely, the driver decides whether to mute the speaker or not, just
depending on the headphone plug state: if one of the headphone jacks
is seen as active, then the speaker is muted.  Thus this will result
always in the muted speaker output.

So, the problem is the function returns a boolean, after all, although
we need to think of "phantom" jack.  Now a new function,
snd_hda_jack_detect_state() is introduced to return these tristates.
The generic parser uses this function for checking the headphone or
mic jack states.

Meanwhile, the behavior of snd_hda_jack_detect() is kept as is, for
keeping compatibility in other driver codes.
Acked-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This Conexant codec has a single jack that can be used as either
headphone or mic (but not headset). The existing hp_mic functionality
does not apply here, because the mic and the HP are on separate pins.

Hence make a lighter version of what has been earlier done for Realtek
codecs.

BugLink: https://bugs.launchpad.net/bugs/1198030Tested-by: NFranz Hsieh <franz.hsieh@canonical.com>
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

sound/pci/rme9652/hdspm.c:1110:2-3: Unneeded semicolon

Generated by: coccinelle/misc/semicolon.cocci
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Commit 8f898e92 removed the redundant
reads of bInterfaceProtocol from the descriptors, but introduced a
regression to devices with quirks of type QUIRK_AUDIO_FIXED_ENDPOINT,
since fp->protocol is not set in setup process.

As a consequence, audio streams would not get initialized, as the
following logs show:

[   48.923043] setting usb interface 3:1
[   48.923056] Creating new capture data endpoint #81
[   48.923484] 4:3:1: cannot set freq 48000 to ep 0x81

This patch sets fp->protocol in create_fixed_stream_quirk() and
resolves the regression.
Signed-off-by: NEldad Zack <eldad@fogrefinery.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

"pcm" member in struct fwspk is used to set pcm operations but is not used
again. This commit remove this member and set pcm operations with
snd_pcm_set_ops().
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ALC5505 DSP is enabled even though we don't use the features yet at
all.  This results in the unnecessarily high power consumption, more
than 100mV higher.  Until we implement the DSP support, better to
bypass DSP for saving more power.
Reported-by: NMengdong Lin <mengdong.lin@intel.com>
[Patch modified by Mengdong to cal alc5505_dsp_init() with extra
acl5505_dsp_halt().]
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NMartin Dausel <martin.dausel@iosono-sound.com>
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Also use snd_ctl_enum_info() to fill the autosync text fields on AES32
and MADI cards (only users of snd_hdspm_info_autosync_ref).
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Also use snd_ctl_enum_info() to fill the autosync enumerated controls.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Use snd_ctl_enum_info() to fill most of the enumerated controls. More
non-trivial occurrences will follow in separate commits.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch finally enables TCO support on RME AES(32) cards.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch adds a new ALSA control to read the external sample rate from
userspace on RME AES(32) cards.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch refactors the code to query the external sample rate and its
translation into the corresponding enum into a helper function to
prevent future code duplication.

A later commit will make use of this new helper function.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Also report TCO status and Sync-In via /proc/ on AES(32) cards.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch enables the user to select "TCO" and "Sync In" as a preferred
sync reference on RME AES(32) cards.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch adds support to read the TCO sample rate in
hdspm_external_sample_rate() on RME AES(32) cards.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

As mentioned in the comment, the AES32 cards must not set the format
bit, since it is used to indicate the preferred sync setting instead.

We hence simply skip the corresponding part in the hw_params function.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch adds AES32 specific code to hdspm_get_tco_sample_rate to
query the TCO sample rate.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch adds AES32 specific code to hdspm_get_wc_sample_rate() to
query the wordclock frequency.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch only introduces prototype declarations, no real change. The
functions themselves are already present.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Helper function to return the AES sample rate class. This class needs to
be translated via HDSPM_bit2freq() to get the more common
representation.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Provide the text for the two new clock options "TCO" and "Sync In" on
AES32 cards.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The HDSPM_AUTOSYNC_REF macro is only implemented for MADI and AES32
cards, so it doesn't make sense to call it on AIO boards.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch does nothing, it's sole intent is to clean up the code.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

HDSPM_tco_lock and HDSPM_tcoLock were too close, so the previous code
didn't honour the difference between the two.

Let's be more verbose and use HDSPM_tcoLockMadi for MADI cards,
HDSPM_tcoLockAes for AES(32) and fix the code that makes use of both.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch separates the TCO bits from snd_hdspm_proc_read_madi(), so
the new function can later be shared between MADI and AES32 cards.

It's essentially only moving code around, no new functionality.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This is a left-over mistake from old code, the correct register offset is
provided in kcontrol->private_value, not in the index.
Cf. RayDAT case, where it has already been corrected.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

AIO cards allow to use AEB (Analogue Expansion Boards) to add four
input and/or output channels.

This patch adds the necessary code to detect and enable the additional
I/O channels.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch uses the newly introduced HDSPM_CONTROL_TRISTATE functions to
create and expose the following ALSA controls:

   - Gain selection for Input, Output and Phones (HiGain, +4dBu, -10dbV)
   - S/PDIF Input select (Coaxial, Optical, Internal)
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

AIO cards offer at least four individual settings options with three
states each. Those settings are represented as two bits in the settings
register with the following meaning:

   0*some_base_bit --> Option value 0
   1*some_base_bit --> Option value 1
   2*some_base_bit --> Option value 2
   3*some_base_bit --> mask to select the two involved bits

This patch adds a generic ALSA control macro for such a value-to-bit
pattern mapping. It will be used in a later commit to expose four new
controls.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ENUMERATED_CTL_INFO is a macro, so the binary code is generated multiple
times. To avoid code duplication, refactor the involved functionality
into a function and make ENUMERATED_CTL_INFO a call to this function.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit adds the following ALSA controls:

   - S/PDIF Out Optical to switch S/PDIF Out from coaxial to optical
   - S/PDIF Out Professional to send the Pro bit in the output stream
   - ADAT-Internal to enable ADAT/TDIF Expansion Board (AEB/TEB)
   - XLR Breakout Cable if analogue I/O uses the XLR breakout cable
   - WCK48 to force WordClock to the 32-48kHz range (single speed) if
     the card is operating at higher frequencies
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>