This fixes various bugs in the init and shutdown code
that would lead to lockups and crashes.
Signed-Off-By: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch sets the floor of wireless level (signal) and noise at
-110 dBm, which makes them be comatible with RCPI, as discussed by
Simon Barber. With this change, bcm43xx-softmac and bcm43xx-d80211
behave the same.
Signed-Off-By: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When bcm43xx-softmac is given an ifdown/ifup sequence, the value for
bcm->mac_suspended ends up wrong, which leads to a large number of
assert(bcm->mac_suspended>=0) messages. This one-line patch fixes
this problem.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-Off-By: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

hard_start_xmit should return a NETIF_TX_FOO error code.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-Off-By: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Convert the bitfields in the bcm43xx DMA code to properly
aligned u8 booleans. These flags are accessed in the DMA
hotpath, so it's a good idea to waste a few bytes of memory
for the sake of speed by not requiring masking (and probably
shifting) of the bitfields.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-Off-By: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Calls to bcm43xx_rng_init() and bcm43xx_rng_exit() got
lost due to merge trouble. Re-add them.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is a rewrite of the bcm43xx DMA engine. It adds support
for >1G of memory (for chips that support the extension bits)
and 64-bit DMA (for chips that support it).
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Drop the mac_suspend loop count to reduce the maximum delay to 10ms.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix-up missing mac_suspended initialization which resulted from
Linville's sloppy patch mangling.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This minor patch for wireless-2.6 (softmac) adjusts the parameters of
the wireless statistics to improve the display of programs such as the
"Wireless Network Information" applet of KDE. Thanks to Dan Williams
and Jean Tourrilhes for valuable help in setting up the return of
info in dBm.
Signed-Off-By: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rewrite of the bcm43xx initialization routines.
This fixes several issues:
* up-down-up-down-up... stale data issue
  (May fix some DHCP issues)
* Fix the init vs IRQ handler race (and remove the workaround)
* Fix init for cards with multiple cores (APHY)
  As softmac has no internal PHY handling (unlike dscape),
  this adds the file "phymode" to sysfs.
  The active PHY can be selected by writing either a, b or g
  to this file. Current PHY can be determined by reading from it.
* Fix the controller restart code.
  Controller restart can now also be triggered through
  echo 1 > /debug/bcm43xx/ethX/restart
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes mac_suspend reference counting for
ifconfig up
ifconfig down
ifconfig up
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Microoptimization:
This reduces the udelay in bcm43xx_mac_suspend.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Suspend MAC (and make MAC-suspend refcounting) when doing
long periodic work.
On long periodic work, we disable IRQs on the device, so
we don't want the MAC to stay operating and probably miss
packets due do non-delivery of interrupts.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Johann Uhrmann reported a bcm43xx crash and Michael Buesch tracked
it down to a problem with the new shared key auth code (recursive
calls into the driver)

This patch (effectively Michael's patch with a couple of small
modifications) solves the problem by sending the authentication
challenge response frame from a workqueue entry.

I also removed a lone \n from the bcm43xx messages relating to
authentication mode - this small change was previously discussed but
not patched in.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch improves the statistics returned from
bcm43xx_get_wireless_stats. The signal level comes from smoothing the
"rssi" value returned by the firmware after it is converted into a
dBm value by the driver. The quality value is a hack derived from the
smoothed level and an assumed RX_POWER_MAX of -10 dBM. The noise value
is still the one calculated from the clean-room formula. On my system,
this is roughly -65 dBm, which seems too high.

The revised version uses the ieee80211 spinlock to protect traversing
of the network list.
Signed-Off-By: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds voluntary preemption points into the
PHY calibration loops to allow non-CONFIG_PREEMPT machines
to not suffer from huge delays.
CONFIG_PREEMPT machines are already fine, because all this
code is run in non-atomic process context.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As many people don't seem to like the locking "obfuscation"
in the bcm43xx driver, this patch removes it.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

An assert statement near the start of handle_irq_noise in the softmac
version of bcm43xx_main.c is there to protect against out of bound
addressing using variable bcm->noisecalc.nr_samples. The arrays in
question have a dimension of 8, thus the value must be < 8.
Signed-Off-By: NLarry.Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I recently patched softmac to enable shared key authentication. This small patch
will enable crazy or unfortunate bcm43xx users to use this new capability.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current version of bcm43xx-softmac uses local routines to check
if a channel is valid. As noted in the comments, these routines do
not take any regulatory information into account. This patch converts
the code to use the equivalent routine in ieee80211, which is being
converted to know about regulatory information.
Signed-Off-By: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Place the Init-vs-IRQ workaround before any card register
access, because we might not have the wireless core mapped
at all times in init. So this will result in a Machine Check
caused by a bus error.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use Softmac-suggested TX ratecode:
ieee80211softmac_suggest_txrate()
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

include/linux/version.h contained both actual KERNEL version
and UTS_RELEASE that contains a subset from git SHA1 for when
kernel was compiled as part of a git repository.
This had the unfortunate side-effect that all files including version.h
would be recompiled when some git changes was made due to changes SHA1.
Split it out so we keep independent parts in separate files.

Also update checkversion.pl script to no longer check for UTS_RELEASE.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

bcm43xx avoid pci_find_device

Change pci_find_device to safer pci_get_device with support for more
devices.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make the heavy periodic work preemptible to avoid disabling
local IRQs for several msecs.
Signed-off-by: NMichael Buesch <mb@buesch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Redesign the bcm43xx locking.
This is pre-work to get a preemptible periodic work handler.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The debug logging in bcm43xx_ieee80211_set_security() is pretty noisy.
Make it more silent.
Signed-off-by: NJason Lunz <lunz@falooley.org>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also add the Poll RX DMA Memory workaround to the DMA4
(xmitstatus) path.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I still need this hack to work around the fact that softmac doesn't
attempt to associate when we bring the device up...
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add PCI ID for bcm4319.
Signed-off-by: NStefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix whitespace.
Signed-off-by: NStefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix the conditions under which we poke at the APHY registers in
bcm43xx_phy_initg() to avoid a machine check on chips where they don't
exist.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The problem here is that the bcm34xx driver and the ieee80211
stack do not agree on what channels are possible for 802.11a.
The ieee80211 stack only wants channels between 34 and 165, while
the bcm43xx driver accepts anything from 0 to 200. I made the
bcm43xx driver comply with the ieee80211 stack expectations, by
using the proper constants.
Signed-off-by: NJean Delvare <jdelvare@suse.de>

[mb]: Reduce stack usage by kzalloc-ing ieee80211_geo
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Check for valid MAC address in SPROM fields instead of relying on
PHY type while setting the MAC address in the networking subsystem,
as some devices have multiple PHYs.
Signed-off-by: NStefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes a crash when

	iwconfig ethX mode foo

is done before

	ifconfig ethX up

or after

	ifconfig ethX down
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reduces codesize.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>