Add support for the MV88E6097 switch. The change was tested on an Armada
based platform with a MV88E6097 switch.
Signed-off-by: NStefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make it possible to generate trace events for mdio read and write accesses.
Signed-off-by: NUwe Kleine-König <uwe@kleine-koenig.org>
Acked-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The VMware VMCI transport supports loopback inside virtual machines.
This patch implements loopback for virtio-vsock.

Flow control is handled by the virtio-vsock protocol as usual.  The
sending process stops transmitting on a connection when the peer's
receive buffer space is exhausted.

Cathy Avery <cavery@redhat.com> noticed this difference between VMCI and
virtio-vsock when a test case using loopback failed.  Although loopback
isn't the main point of AF_VSOCK, it is useful for testing and
virtio-vsock must match VMCI semantics so that userspace programs run
regardless of the underlying transport.

My understanding is that loopback is not supported on the host side with
VMCI.  Follow that by implementing it only in the guest driver, not the
vhost host driver.

Cc: Jorgen Hansen <jhansen@vmware.com>
Reported-by: NCathy Avery <cavery@redhat.com>
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All conflicts were simple overlapping changes except perhaps
for the Thunder driver.

That driver has a change_mtu method explicitly for sending
a message to the hardware.  If that fails it returns an
error.

Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.

However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Both of these drivers won't work on 64-bit architectures unless they
are redesigned, since they store a virtual address pointer in a 32-bit
field of the descriptors:

drivers/net/ethernet/marvell/mvneta_bm.c: In function 'mvneta_bm_construct':
drivers/net/ethernet/marvell/mvneta_bm.c:103:16: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
drivers/net/ethernet/marvell/mvpp2.c: In function 'mvpp2_prs_vlan_init':
drivers/net/ethernet/marvell/mvpp2.c:2563:32: error: large integer implicitly truncated to unsigned type [-Werror=overflow]

This limits the COMPILE_TEST option for the two drivers again to
only build them on 32-bit. This seems nicer than shutting up the
warnings, in case we ever actually want to use them on 64-bit,
as the warnings indicate which parts of the driver are currently
broken there.

Fixes: a0627f77 ("net: marvell: Allow drivers to be built with COMPILE_TEST")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: core: Implement thermal zone

Implement thermal zone for mlxsw based HW.
The first patch is just a register dependency for the second patch.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement thermal zone for mlxsw based HW. It uses temperature sensor
provided by ASIC (the same as mlxsw hwmon interface) to report current
temp to thermal core. The ASIC's PWM is then used to control speed
of system fans registered as cooling devices.
Signed-off-by: NIvan Vecera <cera@cera.cz>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MFSL register is used to configure the fan speed event / interrupt
notification mechanism. Fan speed threshold are defined for both
under-speed and over-speed.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
Start adding support for mv88e6390

This is the first patchset implementing support for the mv88e6390
family.  This is a new generation of switch devices and has numerous
incompatible changes to the registers. These patches allow the switch
to the detected during probe, and makes the statistics unit work.

These patches are insufficient to make the mv88e6390 functional. More
patches will follow.

v2:
  Move stats code into global1
  Change DT compatible string to mv88e6190
  Fixed mv88e6351 stats which v1 had broken
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the stats functions which access global 1 registers into
global1.c.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mv88e6390 uses a different bit to select between bank0 and bank1
of the statistics. So implement an ops function for this, and pass the
selector bit to the generic stats read function. Also, the histogram
selection has moved for the mv88e6390, so abstract its selection as
well.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Different families have different sets of statistics. Abstract this
using a stats_get_stats op. The mv88e6390 needs a different
implementation, which will be added later.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Different families have different sets of statistics. Abstract this
using a stats_get_sset_count and stats_get_strings op. Each stat has a
bitmap, and the ops implementer uses a bit map mask to count the
statistics which apply for the family, or return the list of strings.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
v2:
  Rename functions to avoid _ prefix.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The statistics unit on the mv88e6390 needs the histogram mode to be
configured in a different register compared to other devices. Add an
ops to do this.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
v2:
  Rename to mv88e6390_g1_stats_set_histogram
  Move into global1.c
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MV88E6390 has a control register for what the histogram statistics
actually contain. This means the stat_snapshot method should not set
this information. So implement the 6390 stats_snapshot function without
these bits.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Knowing the family of device belongs to helps with picking the ops
implementation which is appropriate to the device. So add a comment to
each structure of ops.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Taking a stats snapshot differs between same families. Abstract this
into an ops member. At the same time, move the code into global1.[ch],
since the registers are in the global1 range.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the devices added to the tables, the probe will recognize the
switch. This however is not sufficient to make it work properly, other
changes are needed because of incompatibilities.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

_mv88e6xxx_stats_wait() did not check the return value from
 mv88e6xxx_g1_read(), so the compiler complained about set but unused
 err.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The switch needs to be taken out of reset before we can read its ID
register on the MDIO bus.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull apparmor bugfix from James Morris:
 "This has a fix for a policy replacement bug that is fairly serious for
  apache mod_apparmor users, as it results in the wrong policy being
  applied on an network facing service"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  apparmor: fix change_hat not finding hat after policy replacement

Pull sparc fixes from David Miller:

 1) With modern networking cards we can run out of 32-bit DMA space, so
    support 64-bit DMA addressing when possible on sparc64. From Dave
    Tushar.

 2) Some signal frame validation checks are inverted on sparc32, fix
    from Andreas Larsson.

 3) Lockdep tables can get too large in some circumstances on sparc64,
    add a way to adjust the size a bit. From Babu Moger.

 4) Fix NUMA node probing on some sun4v systems, from Thomas Tai.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc: drop duplicate header scatterlist.h
  lockdep: Limit static allocations if PROVE_LOCKING_SMALL is defined
  config: Adding the new config parameter CONFIG_PROVE_LOCKING_SMALL for sparc
  sunbmac: Fix compiler warning
  sunqe: Fix compiler warnings
  sparc64: Enable 64-bit DMA
  sparc64: Enable sun4v dma ops to use IOMMU v2 APIs
  sparc64: Bind PCIe devices to use IOMMU v2 service
  sparc64: Initialize iommu_map_table and iommu_pool
  sparc64: Add ATU (new IOMMU) support
  sparc64: Add FORCE_MAX_ZONEORDER and default to 13
  sparc64: fix compile warning section mismatch in find_node()
  sparc32: Fix inverted invalid_frame_pointer checks on sigreturns
  sparc64: Fix find_node warning if numa node cannot be found

Pull networking fixes from David Miller:

 1) Clear congestion control state when changing algorithms on an
    existing socket, from Florian Westphal.

 2) Fix register bit values in altr_tse_pcs portion of stmmac driver,
    from Jia Jie Ho.

 3) Fix PTP handling in stammc driver for GMAC4, from Giuseppe
    CAVALLARO.

 4) Fix udplite multicast delivery handling, it ignores the udp_table
    parameter passed into the lookups, from Pablo Neira Ayuso.

 5) Synchronize the space estimated by rtnl_vfinfo_size and the space
    actually used by rtnl_fill_vfinfo. From Sabrina Dubroca.

 6) Fix memory leak in fib_info when splitting nodes, from Alexander
    Duyck.

 7) If a driver does a napi_hash_del() explicitily and not via
    netif_napi_del(), it must perform RCU synchronization as needed. Fix
    this in virtio-net and bnxt drivers, from Eric Dumazet.

 8) Likewise, it is not necessary to invoke napi_hash_del() is we are
    also doing neif_napi_del() in the same code path. Remove such calls
    from be2net and cxgb4 drivers, also from Eric Dumazet.

 9) Don't allocate an ID in peernet2id_alloc() if the netns is dead,
    from WANG Cong.

10) Fix OF node and device struct leaks in of_mdio, from Johan Hovold.

11) We cannot cache routes in ip6_tunnel when using inherited traffic
    classes, from Paolo Abeni.

12) Fix several crashes and leaks in cpsw driver, from Johan Hovold.

13) Splice operations cannot use freezable blocking calls in AF_UNIX,
    from WANG Cong.

14) Link dump filtering by master device and kind support added an error
    in loop index updates during the dump if we actually do filter, fix
    from Zhang Shengju.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (59 commits)
  tcp: zero ca_priv area when switching cc algorithms
  net: l2tp: Treat NET_XMIT_CN as success in l2tp_eth_dev_xmit
  ethernet: stmmac: make DWMAC_STM32 depend on it's associated SoC
  tipc: eliminate obsolete socket locking policy description
  rtnl: fix the loop index update error in rtnl_dump_ifinfo()
  l2tp: fix racy SOCK_ZAPPED flag check in l2tp_ip{,6}_bind()
  net: macb: add check for dma mapping error in start_xmit()
  rtnetlink: fix FDB size computation
  netns: fix get_net_ns_by_fd(int pid) typo
  af_unix: conditionally use freezable blocking calls in read
  net: ethernet: ti: cpsw: fix fixed-link phy probe deferral
  net: ethernet: ti: cpsw: add missing sanity check
  net: ethernet: ti: cpsw: fix secondary-emac probe error path
  net: ethernet: ti: cpsw: fix of_node and phydev leaks
  net: ethernet: ti: cpsw: fix deferred probe
  net: ethernet: ti: cpsw: fix mdio device reference leak
  net: ethernet: ti: cpsw: fix bad register access in probe error path
  net: sky2: Fix shutdown crash
  cfg80211: limit scan results cache size
  net sched filters: pass netlink message flags in event notification
  ...

Declare the structure ieee802154_ops as const as it is only passed as an
argument to the function  ieee802154_alloc_hw. This argument is of type
const struct ieee802154_ops *, so ieee80254_ops structures having this
property can be declared as const.
Done using Coccinelle:

@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct ieee802154_ops i@p = {...};

@ok1@
identifier r1.i;
position p;
expression e1;
@@
ieee802154_alloc_hw(e1,&i@p)

@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p

@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct ieee802154_ops  i={...};

@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct ieee802154_ops  i;

The before and after size details of the affected files are:

   text	   data	    bss	    dec	    hex	filename
   8669	   1176	     16	   9861	   2685	drivers/net/ieee802154/adf7242.o
   8805	   1048	     16	   9869	   268d	drivers/net/ieee802154/adf7242.o

   text	   data	    bss	    dec	    hex	filename
   7211	   2296	     32	   9539	   2543	drivers/net/ieee802154/atusb.o
   7339	   2160	     32	   9531	   253b	drivers/net/ieee802154/atusb.o
Signed-off-by: NBhumika Goyal <bhumirks@gmail.com>
Acked-by: NStefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pravin B Shelar says:

====================
geneve: Use LWT more effectively.

Following patch series make use of geneve LWT code path for
geneve netdev type of device.
This allows us to simplify geneve module without changing any
functionality.

v2-v3:
Rebase against latest net-next.

v1-v2:
Fix warning reported by kbuild test robot.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rather than comparing 64-bit tunnel-id, compare tunnel vni
which is 24-bit id. This also save conversion from vni
to tunnel id on each tunnel packet receive.
Signed-off-by: NPravin B Shelar <pshelar@ovn.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Geneve already has check for device socket in route
lookup function. So no need to check it in xmit
function.
Signed-off-by: NPravin B Shelar <pshelar@ovn.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are minimal difference in building Geneve header
between ipv4 and ipv6 geneve tunnels. Following patch
refactors code to unify it.
Signed-off-by: NPravin B Shelar <pshelar@ovn.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current geneve implementation has two separate cases to handle.
1. netdev xmit
2. LWT xmit.

In case of netdev, geneve configuration is stored in various
struct geneve_dev members. For example geneve_addr, ttl, tos,
label, flags, dst_cache, etc. For LWT ip_tunnel_info is passed
to the device in ip_tunnel_info.

Following patch uses ip_tunnel_info struct to store almost all
of configuration of a geneve netdevice. This allows us to unify
most of geneve driver code around ip_tunnel_info struct.
This dramatically simplify geneve code, since it does not
need to handle two different configuration cases. Removes
duplicate code, single code path can handle either type
of geneve devices.
Signed-off-by: NPravin B Shelar <pshelar@ovn.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Westphal says:

====================
tcp: make undo_cwnd mandatory for congestion modules

highspeed, illinois, scalable, veno and yeah congestion control algorithms
don't provide a 'cwnd_undo' function.  This makes the stack default to a
'reno undo' which doubles cwnd.  However, the ssthresh implementation of
these algorithms do not halve the slowstart threshold. This causes similar
issue as the one fixed for dctcp in ce6dd233 ("dctcp: avoid bogus
doubling of cwnd after loss").

In light of this it seems better to remove the fallback and make undo_cwnd
mandatory.

First patch fixes those spots where reno undo seems incorrect by providing
.cwnd_undo functions, second patch removes the fallback.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The undo_cwnd fallback in the stack doubles cwnd based on ssthresh,
which un-does reno halving behaviour.

It seems more appropriate to let congctl algorithms pair .ssthresh
and .undo_cwnd properly. Add a 'tcp_reno_undo_cwnd' function and wire it
up for all congestion algorithms that used to rely on the fallback.

Cc: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

congestion control algorithms that do not halve cwnd in their .ssthresh
should provide a .cwnd_undo rather than rely on current fallback which
assumes reno halving (and thus doubles the cwnd).

All of these do 'something else' in their .ssthresh implementation, thus
store the cwnd on loss and provide .undo_cwnd to restore it again.

A followup patch will remove the fallback and all algorithms will
need to provide a .cwnd_undo function.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nikolay Aleksandrov says:

====================
bridge: add support for IGMPv3 and MLDv2 querier

This patch-set adds support for IGMPv3 and MLDv2 querier in the bridge.
Two new options which can be toggled via netlink and sysfs are added that
control the version per-bridge:
 multicast_igmp_version - default 2, can be set to 3
 multicast_mld_version - default 1, can be set to 2 (this option is
                         disabled if CONFIG_IPV6=n)

Note that the names do not include "querier", I think that these options
can be re-used later as more IGMPv3 support is added to the bridge so we
can avoid adding more options to switch between v2 and v3 behaviour.

The set uses the already existing br_ip{4,6}_multicast_alloc_query
functions and adds the appropriate header based on the chosen version.

For the initial support I have removed the compatibility implementation
(RFC3376 sec 7.3.1, 7.3.2; RFC3810 sec 8.3.1, 8.3.2), because there are
some details that we need to sort out.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds basic support for MLDv2 queries, the default is MLDv1
as before. A new multicast option - multicast_mld_version, adds the
ability to change it between 1 and 2 via netlink and sysfs.
The MLD option is disabled if CONFIG_IPV6 is disabled.
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds basic support for IGMPv3 queries, the default is IGMPv2
as before. A new multicast option - multicast_igmp_version, adds the
ability to change it between 2 and 3 via netlink and sysfs. The option
struct member is in a 4 byte hole in net_bridge.

There also a few minor style adjustments in br_multicast_new_group and
br_multicast_add_group.
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to zero out the private data area when application switches
connection to different algorithm (TCP_CONGESTION setsockopt).

When congestion ops get assigned at connect time everything is already
zeroed because sk_alloc uses GFP_ZERO flag.  But in the setsockopt case
this contains whatever previous cc placed there.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tc could return NET_XMIT_CN as one congestion notification, but
it does not mean the packe is lost. Other modules like ipvlan,
macvlan, and others treat NET_XMIT_CN as success too.
So l2tp_eth_dev_xmit should add the NET_XMIT_CN check.
Signed-off-by: NGao Feng <gfree.wind@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function macvlan_forward_source_one has already checked the flag
IFF_UP, so needn't check it outside in macvlan_forward_source too.
Signed-off-by: NGao Feng <gfree.wind@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's not much point, except compile test, enabling the stmmac
platform drivers unless the STM32 SoC is enabled. It's not
useful without it.
Signed-off-by: NPeter Robinson <pbrobinson@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While stressing a 40Gbit mlx4 NIC with busy polling, I found false
sharing in mlx4 driver that can be easily avoided.

This patch brings an additional 7 % performance improvement in UDP_RR
workload.

1) If we received no frame during one mlx4_en_process_rx_cq()
   invocation, no need to call mlx4_cq_set_ci() and/or dirty ring->cons

2) Do not refill rx buffers if we have plenty of them.
   This avoids false sharing and allows some bulk/batch optimizations.
   Page allocator and its locks will thank us.

Finally, mlx4_en_poll_rx_cq() should not return 0 if it determined
cpu handling NIC IRQ should be changed. We should return budget-1
instead, to not fool net_rx_action() and its netdev_budget.

v2: keep AVG_PERF_COUNTER(... polled) even if polled is 0
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>