The fast firmware load hack in cx25840 uses private data. In fact, it
breaks pvrusb2 and doesn't work at all with ivtv. It is a unsafe
implementation and so it is removed.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch prevents a bug where the frontend is unable to tune after waking
from powered down state. Now, the device remains powered on until it is
disconnected, just like the windows driver. It seems that the bluebird
firmware is unable to successfully handle tuning after a powered down state.
This patch fixes all of the FusionHDTV Bluebird USB2 devices. The Medion
MD95700 will still behave as before, since it was unaffected by this bug.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

*) Allow forcing the bandselect value with a module parameter to 
facilitate determining the correct bandselect frequencies.
*) Changes the bandselect frequency thresholds based on experiments 
with the above parameter in conjunction with the values in the spec.

Signed-off-by: Yeasah Pell <yeasah at schwide.net>
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

*) Sets an additional tuner parameter (demodulator sample gain) that 
wasn't being set before.
*) Removes the low symbol rate tuner parameter tweaks in the previous 
patch -- it appears those tweaks are not necessary with the demodulator 
sample gain set correctly.
*) Cleanup and document the demodulator register initialization sequence.
*) Change set_fec routine to disable FEC auto scan when a specific code 
rate is selected.
*) Remove error message when reported FEC is invalid (which happens 
sometimes when the card has no signal)

Signed-off-by: Yeasah Pell <yeasah at schwide.net>
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The previous DISEQC code didn't wait, so it was unreliable

Signed-off-by: Yeasah Pell <yeasah at schwide.net>
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Current debug messages at cx24123 are next to useless, since they don't
print the values sent/read to registers. With this patch, debug=1 will
show comprehensive messages. debug=2 will show also read/write operations
at I2C bus.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>

- fixed the reception of channels with low symbol rates.
  ( The VGA1 and VGA2 offsets recommended by cx24109 docs for
  symbol rates from 1 to 5 MSps do not work. I changed them
  to values found experimentally. The charge pump current
  and FILTUNE voltage are now set to values recommended in
  the docs. This improves reception for symbol rates < 15 MSps.
  The values written in the SYSSymbolRate registers are calculated
  with better precision. )
		     
- fixed the cx24123_get_fec() function. It was returning the values
  for DCII mode.
- removed some unused variables

Signed-off-by: Vadim Catana <skystar at moldova.cc>
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

In several places we use dev->devno right after we kfree() dev.  This fixes
coverity bug id #1065
Signed-off-by: NEric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

V4L1 API is depreciated and should be removed soon from kernel. This patch
adds two new options, one to disable V4L1 drivers, and another to disable
V4L1 compat module. This way, it would be easy to check what still depends
on V4L1 stuff, allowing also to test if app works fine with V4L2 only support.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Witout this patch tv out don't work properly with my pvr350 card.
Signed-off-by: NJose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The computation in cx88_risc_buffer suffers from the mistake:
a non-zero padding value can cause more page borders to be crossed,
leading to big buffer over-runs.  
This patch changes the additive constant from 3 + 4 to 4
It also changees the constant in cx88_risc_databuffer from 3 + 4 to 2,
because 2 dwords are the correct vaule.
Signed-off-by: NDuncan Sands <baldrick@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

It looks like the HD3000 was prototyped with the 7610 tuner when
the driver was developed, but the cards appear to have always shipped
with the 7612 tuner and the driver was never adjusted for it.
The definition needs to be corrected.
- The HD-3000 was prototyped with a Thomson DTT7610,
  but production versions used a DTT7612 tuner.
- This patch changes both dvb-pll settings and V4L tuner type.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When pluto2 were selected, all other module dependencies were
just discarded.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Spotted a couple more places where it fails to check if
dvb_register_adapter() fails.
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Now that the CI code reinitialises the frontend, need to move the CI
initialisation to after the frontend init in order to ensure the frontend is
always in a good state. Fixes an oops caused by the frontend being NULL as
well.
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When disable_ir=1 parameter is used, or when saa7134_input_init1()
fails for any other reason, dev->remote will remain NULL, and the
driver will oops in saa7134_hwinit2().  Therefore dev->remote must be
checked before dereferencing.
Signed-off-by: NSergey Vlasov <vsu@altlinux.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- replaced '$(src)/..' with 'drivers/media/video'
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

It turns out the firmware on the TT budget-ci 1.1 slots doesn't generate
interrupts. This patch adds support for this using polling mode on these
slots.
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This mutex is meant to stop two devices getting the same ID. dvbdev_get_free_id() 
scans the list of already allocated devices to find a free id.
Unfortunately, since the mutex is unlocked before the card is added to the
above list, it is still possible for two of them to get the same id.
Its debatable whether this mutex lock is actually needed, but I'm unwilling
to just remove it in case something does depend on it.
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

There are tree mistakes on bttv_risc_overlay.
1) When skip_odd is true, the number of lines for which
instructions are written is (height+1)/2, not height/2.
2) This occurs when clipping: the number of instruction bytes
written can be as much as 8 + 12*nclips, not 8 + 8*nclips, as
currently estimated.
3) Coverity check were wrong with nskips=0, since it means that
it can clipped at most one line.
Signed-off-by: NDuncan Sands <baldrick@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC]: Fix warning on prom_getproperty in openprom.c
  [SPARC]: Handle UNWIND_INFO properly.
  [SPARC64]: Update defconfig.
  [SPARC]: show device name in /proc/dvma_map
  [SPARC]: Remove duplicate symbol exports

Fix race condition during destruction calls to avoid possibility of
accessing object after it has been freed.  Instead of waking up a wait
queue directly, which is susceptible to a race where the object is
freed between the reference count going to 0 and the wake_up(), use a
completion to wait in the function doing the freeing.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The ipath driver's table of PCI IDs needs a { 0, } entry at the end.
This makes all of the device aliases visible to userspace so hotplug
loads the module for all supported devices.  Without the patch,
modinfo ipath_core only shows:

    alias:          pci:v00001FC1d0000000Dsv*sd*bc*sc*i*

instead of the correct:

    alias:          pci:v00001FC1d00000010sv*sd*bc*sc*i*
    alias:          pci:v00001FC1d0000000Dsv*sd*bc*sc*i*
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Signed-off-by: NBryan O'Sullivan <bos@pathscale.com>

Signed-off-by: NMartin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For sparc32 we need R_SPARC_UA32 relocation support, for
sparc64 we need the handle R_SPARC_DISP32 relocations.

Based upon reports and initial patch by Martin Habets.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/i2c-2.6:
  [PATCH] scx200_acb: Fix for the CS5535 errata
  [PATCH] scx200_acb: Fix resource name use after free
  [PATCH] scx200_acb: Fix return on init error

* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  [PATCH] USB: fix omninet driver bug
  [PATCH] USB: add ark3116 usb to serial driver
  [PATCH] usbserial: Fixes leak in serial_open() error path.
  [PATCH] usbserial: Fixes use-after-free in serial_open().
  [PATCH] USB: Emagic USB firmware loading fixes
  [PATCH] USB: add an IBM USB keyboard to the HID_QUIRK_NOGET blacklist
  [PATCH] USB: Add Sieraa Wireless 580 evdo card to airprime.c
  [PATCH] USB: ftdi_sio: add device id for ACT Solutions HomePro ZWave interface
  [PATCH] USB: ftdi_sio: Add support for HCG HF Dual ISO RFID Reader
  [PATCH] USB: ub oops in block_uevent
  [PATCH] USB: usbcore: don't check the device's power source
  [PATCH] USB: fix OHCI PM regression
  [PATCH] USB: pegasus fixes (logstorm, suspend)
  [PATCH] USBATM: fix modinfo output
  [PATCH] USBATM: change the default speedtouch iso altsetting
  [PATCH] USB: fix bug in ohci-hcd.c ohci_restart()

This reverts commit 56cf6504.

Both Erik Mouw and Andrew Vasquez independently pinpointed this commit
as causing problems, where the slab cache for a driver is never released
(most obviously causing problems when immediately re-loading that
driver, resulting in a "kmem_cache_create: duplicate cache <xyz>"
message, but it can also cause other trouble).

James Bottomley dug into it, and reports:

  "OK, here's the scoop.  The problem patch adds a get of driverfs_dev in
   add_disk(), but doesn't put it again until disk_release() (which occurs
   on final put_disk() of the gendisk).

   However, in SCSI, the driverfs_dev is the sdev_gendev.  That means
   there's a reference held on sdev_gendev  until final disk put.
   Unfortunately, we use the driver model driver_remove to trigger
   del_gendisk (which removes the gendisk from visibility and decrements
   the refcount), so we've introduced an unbreakable deadlock in the
   reference counting with this.

   I suggest simply reversing this patch at the moment.  If Russell and
   Jens can tell me what they're trying to do I'll see if there's another
   way to do it."

so hereby the patch gets reverted, waiting for a better fix.

Cc: Jens Axboe <axboe@suse.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Erik Mouw <erik@harddisk-recovery.com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

I introduced this way back in 2.6.13 when adding the port lock logic.
This device talks out through different "ports" all at the same time, so
the lock logic was wrong, preventing any data from ever being sent
properly.

Thanks a lot to Bernhard Reiter <bernhard@intevation.de> for being
patient and helping with debugging this.

Cc: Bernhard Reiter <bernhard@intevation.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Based on Simon's original driver, with some minor code cleanups and
tidying by me.

Cc: Simon Schulz <simon@auctionant.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If serial_open() fails at the port assignment or mutex_lock_interruptible()
is interrupted, the 'serial' object will never be freed.

We should call kref_put() when those errors happens.
Signed-off-by: NLuiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If the device is disconnected while serial_open() is executing and
either try_module_get() or the device specific open function fails, the
kref_put() call in the 'bailout_kref_put' label will free the memory
pointed out by 'port'.

The subsequent dereferences in the 'bailout_kref_put' label will be
invalid.

The fix is just to assure kref_put() is called after any 'port' usage.
Signed-off-by: NLuiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

It's become apparent as machines get faster that the emagic kernel firmware
loaders (based on the ezusb loader) have a reset race.  a 400MHz TiBook
never tripped it, but a 2GHz Pentium M seems to hit it about 30% of the
time.  The bug is seen as a hung USB box and the kernel error:

drivers/usb/misc/emi62.c: emi62_load_firmware - error loading firmware:
error = -110

The patch below inserts a delay after deasserting reset to allow the box to
settle before a new command is issued.  This affects only device startup.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

After recent changes, the USB keyboard as shipped with IBM pSeries systems
does not work anymore, unless the keyboard is replugged after reboot.
Adding this model to the blacklist fixes it.
Signed-off-by: NOlaf Hering <olh@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>