Since pj4b suspend/resume routines are implemented based on generic
ARMv7 ones, instead of hard-coding cpu_pj4b_suspend_size, we should have
it be cpu_v7_suspend_size plus pj4b specific bytes.  Otherwise, if
cpu_v7_suspend_size gets updated alone, the pj4b suspend/resume will
likely be broken.

While at it, fix the comments in cpu_pj4b_do_resume, as we're restoring
CP15 registers rather than saving in there.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Save and report (via the procfs file) the last kernel unaligned fault
location.  This allows us to trivially inspect where the last fault
happened for cases which we don't expect to occur.

Since we expect the kernel to generate misalignment faults (due to
the networking layer), even when warnings are enabled, we don't log
them for the kernel.
Tested-by: NTony Lindgren <tony@atomide.com>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

ARMv6 and greater introduced a new instruction ("bx") which can be used
to return from function calls.  Recent CPUs perform better when the
"bx lr" instruction is used rather than the "mov pc, lr" instruction,
and this sequence is strongly recommended to be used by the ARM
architecture manual (section A.4.1.1).

We provide a new macro "ret" with all its variants for the condition
code which will resolve to the appropriate instruction.

Rather than doing this piecemeal, and miss some instances, change all
the "mov pc" instances to use the new macro, with the exception of
the "movs" instruction and the kprobes code.  This allows us to detect
the "mov pc, lr" case and fix it up - and also gives us the possibility
of deploying this for other registers depending on the CPU selection.
Reported-by: NWill Deacon <will.deacon@arm.com>
Tested-by: Stephen Warren <swarren@nvidia.com> # Tegra Jetson TK1
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr> # mioa701_bootresume.S
Tested-by: Andrew Lunn <andrew@lunn.ch> # Kirkwood
Tested-by: NShawn Guo <shawn.guo@freescale.com>
Tested-by: Tony Lindgren <tony@atomide.com> # OMAPs
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com> # Armada XP, 375, 385
Acked-by: Sekhar Nori <nsekhar@ti.com> # DaVinci
Acked-by: Christoffer Dall <christoffer.dall@linaro.org> # kvm/hyp
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com> # PXA3xx
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com> # Xen
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> # ARMv7M
Tested-by: Simon Horman <horms+renesas@verge.net.au> # Shmobile
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Ensure that platform maintainers check the CPU part number in the right
manner: the CPU part number is meaningless without also checking the
CPU implement(e|o)r (choose your preferred spelling!)  Provide an
interface which returns both the implementer and part number together,
and update the definitions to include the implementer.

Mark the old function as being deprecated... indeed, using the old
function with the definitions will now always evaluate as false, so
people must update their un-merged code to the new function.  While
this could be avoided by adding new definitions, we'd also have to
create new names for them which would be awkward.
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Commit 1c2f87c2 (ARM: 8025/1: Get rid of meminfo) changed find_limits
to use memblock_get_current_limit for calculating the max_low pfn.
nommu targets never actually set a limit on memblock though which
means memblock_get_current_limit will just return the default
value. Set the memblock_limit to be the end of DDR to make sure
bounds are calculated correctly.
Signed-off-by: NLaura Abbott <lauraa@codeaurora.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

When a PL310 cache is used on a system that provides hardware
coherency, the outer cache sync operation is useless, and can be
skipped. Moreover, on some systems, it is harmful as it causes
deadlocks between the Marvell coherency mechanism, the Marvell PCIe
controller and the Cortex-A9.

To avoid this, this commit introduces a new Device Tree property
'arm,io-coherent' for the L2 cache controller node, valid only for the
PL310 cache. It identifies the usage of the PL310 cache in an I/O
coherent configuration. Internally, it makes the driver disable the
outer cache sync operation.

Note that technically speaking, a fully coherent system wouldn't
require any of the other .outer_cache operations. However, in
practice, when booting secondary CPUs, these are not yet coherent, and
therefore a set of cache maintenance operations are necessary at this
point. This explains why we keep the other .outer_cache operations and
only ->sync is disabled.

While in theory any write to a PL310 register could cause the
deadlock, in practice, disabling ->sync is sufficient to workaround
the deadlock, since the other cache maintenance operations are only
used in very specific situations.

Contrary to previous versions of this patch, this new version does not
simply NULL-ify the ->sync member, because the l2c_init_data
structures are now 'const' and therefore cannot be modified, which is
a good thing. Therefore, this patch introduces a separate
l2c_init_data instance, called of_l2c310_coherent_data.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Commit ca8f0b0a ("ARM: ensure C page table setup code follows
assembly code") did what it said on the tin, but some of the older
CPU code omitted the default cache policy from their files.  This
results in the kernel running with the caches disabled.  Fix this
for ARM925.
Reported-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

A number of configurations spit out warnings similar to:

warning: (SOC_IMX6 && SOC_VF610 && ARCH_OMAP4) selects PL310_ERRATA_588369 which has unmet direct dependencies (CACHE_L2X0)
warning: (SOC_IMX6 && SOC_VF610 && ARCH_OMAP4) selects PL310_ERRATA_727915 which has unmet direct dependencies (CACHE_L2X0)

Clean up the dependencies here:
* PL310 symbols should only be selected when CACHE_L2X0 is enabled.
* Since the cache-l2x0 code detects PL310 presence at runtime, and we will
  eventually get rid of CACHE_PL310, surround these errata options with an
  if CACHE_L2X0 conditional rather than repeating the dependency against
  each.
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Currently hugepage migration is available for all archs which support
pmd-level hugepage, but testing is done only for x86_64 and there're
bugs for other archs.  So to avoid breaking such archs, this patch
limits the availability strictly to x86_64 until developers of other
archs get interested in enabling this feature.

Simply disabling hugepage migration on non-x86_64 archs is not enough to
fix the reported problem where sys_move_pages() hits the BUG_ON() in
follow_page(FOLL_GET), so let's fix this by checking if hugepage
migration is supported in vma_migratable().
Signed-off-by: NNaoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reported-by: NMichael Ellerman <mpe@ellerman.id.au>
Tested-by: NMichael Ellerman <mpe@ellerman.id.au>
Acked-by: NHugh Dickins <hughd@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Miller <davem@davemloft.net>
Cc: <stable@vger.kernel.org>	[3.12+]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This does the same as the previous commit, but for the S bit, which also
needs to match the initial value which the assembly code used for the
same reasons.  Again, we add a check for SMP to ensure that the page
tables are correctly setup for SMP.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix a long standing bug where, for ARMv6+, we don't fully ensure that
the C code sets the same cache policy as the assembly code.  This was
introduced partially by commit 11179d8c ([ARM] 4497/1: Only allow
safe cache configurations on ARMv6 and later) and also by adding SMP
support.

This patch sets the default cache policy based on the flags used by the
assembly code, and then ensures that when a cache policy command line
argument is used, we verify that on ARMv6, it matches the initial setup.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

cr_no_alignment is really only used by the alignment code.  Since we no
longer change the setting of cr_alignment after boot, we can localise
this to alignment.c
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

alignment.c will not be built unless CPU_CP15 is set:

config CPU_CP15
        bool

config CPU_CP15_MMU
        bool
        select CPU_CP15

config ALIGNMENT_TRAP
        bool
        depends on CPU_CP15_MMU

So there's no point having conditionals on CPU_CP15 within this code.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

adjust_cr() is not used anymore, so let's get rid of it.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Keep all bits of alignment handling together.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Several places open-code this manipulation, let's consolidate this.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

memblock is now fully integrated into the kernel and is the prefered
method for tracking memory. Rather than reinvent the wheel with
meminfo, migrate to using memblock directly instead of meminfo as
an intermediate.
Acked-by: NJason Cooper <jason@lakedaemon.net>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Tested-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Tested-by: NLeif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: NLaura Abbott <lauraa@codeaurora.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Due to a design incompatibility between the PCIe Marvell controller
and the Cortex-A9, stressing PCIe devices with a lot of traffic
quickly causes a deadlock.

One part of the workaround for this is to have all PCIe regions mapped
as strongly-ordered (MT_UNCACHED) instead of the default
MT_DEVICE. While the arch_ioremap_caller() mechanism allows
sub-architecture code to override ioremap(), used to map PCIe memory
regions, there isn't such a mechanism to override the behavior of
pci_ioremap_io().

This commit adds the arch_pci_ioremap_mem_type variable, initialized
to MT_DEVICE by default, and that sub-architecture code can
override. We have chosen to expose a single variable rather than
offering the possibility of overriding the entire pci_ioremap_io(),
because implementing pci_ioremap_io() requires calling functions
(get_mem_type()) that are private to the arch/arm/mm/ code.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

As we have now removed all instances of the L2C-310 having its cache
size "modified" via platform/SoC code, discourage new cases showing
up by printing a warning.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

We no longer need or require the .set_debug method; we handle everything
it used to do via the .write_sec method instead.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Provide a common assembly implementation for PL310 resume code.  Certain
platforms need to re-initialise the L2C cache early as it may preserve
data across a S2RAM cycle, and therefore must be enabled along with the
L1 cache and MMU.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Since we always write to these during the cache initialisation, it is
a good idea to always have the non-secure access bit set.  Set it in
core code.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Always enable the L2C low power modes on L2C-310 R3P0 and newer parts.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The AXI bus protocol requires that a write response should only be
sent back to the master when the last write has been accepted.  Early
BRESP allows the L2C-310 to send the write response as soon as the
store buffer accepts the write address.

Cortex-A9 processors can signal to the L2C-310 that they wish to be
notified early, and if this optimisation is enabled, the L2C-310 can
signal an early write response.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Move the L2 cache register saving to a more sensible location - after
the cache has been enabled, and fixups have been run.  We move the
saving of the auxiliary control register into the ->save function as
well which makes everything operate in a sane and maintainable way.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This is a required property, and should always be specified.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

We have a mixture of different devices with different register layouts,
but we group all the bits together in an opaque mess.  Split them out
into those which are L2C-310 specific and ones which refer to earlier
devices.  Provide full auxiliary control register definitions.
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Rather than having SoCs work around L2C erratum themselves, move them
into core code.  This erratum affects the double linefill feature which
needs to be disabled for r3p0 to r3p1-50rel0.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

When Linux is running in the non-secure world, any write to a secure
L2C register will generate an abort.  Platforms normally have to call
firmware to work around this.  Provide a hook for them to intercept
any L2C secure register write.

l2c_write_sec() avoids writes to secure registers which are already set
to the appropriate value, thus avoiding the overhead of needlessly
calling into the secure monitor.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Move the L2C-310 errata configuration options to arch/arm/mm/Kconfig
along side the option which enables support for this device.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Move the way size calculation data (base of way size) out of the
switch statement into the provided initialisation data.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Rather than assuming these are always 8-way, it can be decoded from the
auxillary register in the same manner as L2C-210.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Rather than decoding this from the ID register, store it in the
l2c_init_data structure.  This simplifies things some more, and
allows us to better provide further details as to how we're
driving the cache.  We print the cache ID value anyway should we
need to precisely identify the cache hardware.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

non-OF initialisation has never been used with any cache controller
which isn't an ARM cache controller, so we can safely get rid of the
old (and buggy) l2x0_*-based operations structure.

This is also the last reference to:
- l2x0_clean_line()
- l2x0_inv_line()
- l2x0_flush_line()
- l2x0_flush_all()
- l2x0_clean_all()
- l2x0_inv_all()
- l2x0_inv_range()
- l2x0_clean_range()
- l2x0_flush_range()
- l2x0_enable()
- l2x0_resume()
so kill those functions too.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The Broadcom L2C-310 devices use ARMs L2C-310 R2P3 or later.  These
require no errata workarounds, and so we can directly call the l2c210
functions from their methods.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The L2C-220 is different from the L2C-210 and L2C-310 in that every
operation is a background operation: this means we have to use
spinlocks to protect all operations, and we have to wait for every
operation to complete.

Should a second operation be attempted while a previous operation
is in progress, the response will be an imprecise abort.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Where no errata affect the L2C-310 handlers, they are functionally
equivalent to L2C-210.  Re-use the L2C-210 handlers for the L2C-310
part.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Implement L2C-310 erratum 588369 by overriding the invalidate range
and flush range methods in the outer_cache operations structure.
This allows us to sensibly contain the erratum code in one place
without affecting other locations/implemetations.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>