Add support for usb suspend/resume.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clean code related to firmware download routines. Remove obsolete
delay and increase delay after reset command.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Handling of firmware event has been reworked into a seperate
code file. The change is needed as firmware event can be received
in interrupt context. Decoupling of the event handling has been
lowered to allow event processing to sleep.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

'|' has higher precedence than ?:.  Since AR5K_PHY_TURBO_MODE is 0x1 and
"AR5K_PHY_TURBO_MODE | (ah->ah_radio == AR5K_RF2425)" is true then we
always set turbo to zero.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Simplify the code by make use of module_platform_driver macro.
Signed-off-by: NSyam Sidhardhan <s.syam@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The workaround for ASPM/L0s is needed only for AR9485 1.0,
which was never sold and is not supported by ath9k.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

An issue is reported in AR9462 & AR9565 that NF_cal_not_done is
not observed when HW peak detector calibration is disabled. At that
state, the HW is stuck at NF calibration which prevents tx output.
The root cause is wrong peak detector offset calibrated by HW. To
resolve this issue, peak detector calibration is done manually by SW
for AR9462 and AR9565.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The firmware supports 8 macid's corresponding to 8 BSS that can be
created in an MBSS environment. Currently, BASTREAM commands were always
sent with macid 0. This macid is used to configure the hardware ampdu
registers with appropriate BSS address in an MBSS environment.
This mac address is used by the hardware for various ampdu related requirements
e.g. source address in BAR generation, BA interpretation e.t.c.
Using invalid macid results in this mac address not getting appropriately
configured in the hardware which results in issues during ampdu traffic.

Fix this by sending the BASTREAM commands with appropriate macid.
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Offset for temperature compensation
values is wrong in ssb SPROMv8 map.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add 5% width tolerance for radar patterns defined by ETSI.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Conflicts:
	drivers/net/wireless/iwlwifi/pcie/trans.c

As ath6kl firmware can't do intersections the driver should only listen
to regdom changes from cellular base stations, all other requests need to
be refused.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Set tx packet timestamp to 0 in following scenarios:-
- All packets in STA mode
- Mgmt packets in AP mode
- Eapol packets in AP mode

In STA mode, this field is unused in the firmware. In AP
mode, we should not be expiring mgmt and eapol frames.
Setting timestamp to 0 will ensure that.
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This can cause issues when clients try to connect when the
traffic is heavy
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We should unmap the DMA address in the error path, else it
causes resource leaks. Fix this.
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We have 6.5 Mbps is minimum rate of the link
as the criterion for creation of BA.

Although we check this before creating the BA
stream, by the time amdpu_action is called from
the workqueue, the link can get affected in the
meantime.
Hence, add an additional check in amdpu_action.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AP mode support upto 8 interfaces.
Defining it using iface_combinations
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ksdioirqd has higher priority than kworker. Process RX packets
in SDIO IRQ thread (ksdioirqd/mmcX) directly instead of deferring
the work to kworker to avoid the extra latency.
This improves TCP throughput 15~20% on an ARM platform with SDIO
2.0 controller.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Firmware events are passed to wl_cfg80211 module associated with
the primary net device. With virtual interface support events can
be received for different interfaces, ie. struct brcmf_if instances.
Pass it in the event to determine appropriate net device associated
with the event.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add USB log level and update and add log messages in usb module.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

brcmf_netdev_stop shall first check bus_if status before bringing
down cfg80211. brcmf_detach shall first check if driver is
allocated.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

brcmf_netdev_start_xmit and brcmf_fil_cmd_data are checking
bus state for down. These functions should check for data
state.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

when brcmf_cfg80211_del_key was called with out of range key index
then firmware would return error. Checking was added to
brcmf_cfg80211_del_key to immediately return error.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes a build regression for x86_64 target that showed up
in 3.7-rc1 due to:

commit 1a873342
Author: Hante Meuleman <meuleman@broadcom.com>
Date:   Thu Sep 27 14:17:54 2012 +0200

    brcmfmac: add hostap supoort.
Reported-by: NYuanhan Liu <yuanhan.liu@intel.com>
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Reported-by: NRandy Dunlap <rdunlap@infradead.org>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use int instead of bool as the return type of function
brcmf_sdio_hdparser to explicitly describe error returns.
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

brcmf_sdbrcm_wait_for_event is now a one line function and only
used by brcmf_sdbrcm_bus_txctl. Intergrate the function call
wait_event_interruptible_timeout into brcmf_sdbrcm_bus_txctl.
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Semaphore sdsem is used to protect consecutive memory access
through SDIO bus. Same functionality is provided by sdio_claim_host/
sdio_release_host interface as well. Replace sdsem with
sdio_claim_host.
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Semaphore sdsem which protects consecutive SDIO bus access is used
to lock down unnecessary wide range. Decrease the locking range
provides the capability of parallel processing.
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rxbuf in SDIO interface is used in normal frame and control frame
read. Use dynamically allocated buffer in control frame read path
for post processing to avoid conflicts.
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function brcmf_fil_bsscfg_data_get() calls brcmf_create_iovar()
with data pointer set to NULL, which caused a NULL pointer access.
As it should be possible to provide data in message towards the
firmware, it should just pass the data buffer instead.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

the refactored firmware interface layer made this function obsolete.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function brcmf_cfg80211_start_ap() had some variables declared
that were not used or not needed any longer. This patch removes
those variables.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function brcmf_set_management_ie() operates on virtual
interface data and brcmf_cfg80211_vif structure provides
all information needed for interfacing with firmware. As
this function will also be needed for interface without
an associated net device it makes sense to provide the vif
instead of deriving it from the net device.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

sizeof calculation in setting pkt_filter was incorrect. This
patch fixes that and removes related defines which have become
obsolete.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

brcmf_netdev_wait_pend8021x was polling to see if 8021x data was
already sent. Code was replaced using wait_event_timeout.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On exception during brcmf_bus_start the netdev should be freed,
if already allocated.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Change setting up multicast, mac address and offloading to use the
refactored firmware interface layer. Remove obsolete brcmf_proto_dcmd
function.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>