Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support for multiple BSS interfaces (AP). In
total three AP configurations can be created. In order to use
multiple BSS firmware needs to support it.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The vendor specific commands was always using main interface,
change this to use the by caller supplied interface.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use single message MSI to replace legacy interrupt.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some 43602 devices are band specific and identify themselves
with different PCIE device ID. This patch adds support for the
43602 2.4G and 5.0G devices used in for example R8000 router.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ifidx provided by FW needs to be offsetted when receiving data
packets.

Cc: stable@vger.kernel.org # v3.17, v3.18
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cc: stable@vger.kernel.org # v3.17, v3.18
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Wake On Lan was not working on laptop DELL Vostro 1500.
If WOL was turned on, BCM4401 was powered up in suspend mode. LEDs blinked.
But the laptop could not be woken up with the Magic Packet. The reason for
that was that PCIE was not enabled as a system wakeup source and
therefore the host PCI bridge was not powered up in suspend mode.
PCIE was not enabled in suspend by PM because no child devices were
registered as wakeup source during suspend process.
On laptop BCM4401 is connected through the SSB bus, that is connected to the
PCI-Express bus. SSB and B44 did not use standard PM wakeup functions
and did not forward wakeup settings to their parents.
To fix that B44 driver enables PM wakeup and registers new wakeup source
using device_set_wakeup_enable(). Wakeup is automatically reported to the parent SSB
bus via power.wakeup_path. SSB bus enables wakeup for the parent PCI bridge, if there is any
child devices with enabled wakeup functionality. All other steps are
done by PM core code.
Signed-off-by: NAndrey Skvortsov <Andrej.Skvortzov@gmail.com>
Signed-off-by: NMichael Buesch <m@bues.ch>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Johannes Berg <johannes@sipsolutions.net> says:

"This time I have Felix's no-status rate control work, which will allow
drivers to work better with rate control even if they don't have perfect
status reporting. In addition to this, a small hwsim fix from Patrik,
one of the regulatory patches from Arik, and a number of cleanups and
fixes I did myself.

Of note is a patch where I disable CFG80211_WEXT so that compatibility
is no longer selectable - this is intended as a wake-up call for anyone
who's still using it, and is still easily worked around (it's a one-line
patch) before we fully remove the code as well in the future."
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Samuel Ortiz <sameo@linux.intel.com> says:

"NFC: 3.19 pull request

This is the NFC pull request for 3.19.

With this one we get:

- NFC digital improvements for DEP support: Chaining, NACK and ATN
  support added.

- NCI improvements: Support for p2p target, SE IO operand addition,
  SE operands extensions to support proprietary implementations, and
  a few fixes.

- NFC HCI improvements: OPEN_PIPE and NOTIFY_ALL_CLEARED support,
  and SE IO operand addition.

- A bunch of minor improvements and fixes for STMicro st21nfcb and
  st21nfca"
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The maximum size of ATR_REQ and ATR_RES is 64 bytes.
The maximum number of General Bytes is calculated by
the maximum number of data bytes in the ATR_REQ/ATR_RES,
substracted by the number of mandatory data bytes.

ATR_REQ: 16 mandatory data bytes, giving a maximum of
48 General Bytes.
ATR_RES: 17 mandatory data bytes, giving a maximum of
47 General Bytes.

Regression introduced in commit a99903ec.
Signed-off-by: NJulien Lefrique <lefrique@marvell.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Fixing: net/nfc/nci/ntf.c:106:31: warning: cast to restricted __le16
message when building with make C=1 CF=-D__CHECK_ENDIAN__
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Fix warnings:
net/nfc/llcp_commands.c:421:14: warning: incorrect type in assignment (different base types)
net/nfc/llcp_commands.c:421:14:    expected unsigned short [unsigned] [usertype] miux
net/nfc/llcp_commands.c:421:14:    got restricted __be16
net/nfc/llcp_commands.c:477:14: warning: incorrect type in assignment (different base types)
net/nfc/llcp_commands.c:477:14:    expected unsigned short [unsigned] [usertype] miux
net/nfc/llcp_commands.c:477:14:    got restricted __be16

Procedure to reproduce:
make ARCH=x86_64 allmodconfig
make C=1 CF=-D__CHECK_ENDIAN__
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Report error returned by devm_gpio_request_one instead of -ENODEV.
Reported-by: NDmitry Torokhov <dtor@chromium.org>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Report error returned by devm_gpio_request_one or
st21nfca_hci_platform_init instead of -ENODEV.
Reported-by: NDmitry Torokhov <dtor@chromium.org>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Some pipe are only created by other host (different than the
Terminal Host).
The pipe values will for example be notified by
NFC_HCI_ADM_NOTIFY_PIPE_CREATED.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

se_io allows to send apdu over the CLF to the embedded
Secure Element.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Some tag might get deactivated after some read or write tentative.
This may happen for example with Mifare Ultralight C tag when trying
to read the last 4 blocks (starting block 0x2c) configured as write
only.
NFC_CMD_ACTIVATE_TARGET will try to reselect the tag in order to
detect if it got remove from the field or if it is still present.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

nci_rf_deactivate_req only support NCI_DEACTIVATE_TYPE_IDLE_MODE.
In some situation, it might be necessary to be able to support other
NCI_DEACTIVATE_TYPE such as NCI_DEACTIVATE_TYPE_SLEEP_MODE in order for
example to reactivate the selected target.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

A notification for rf deaction can be IDLE_MODE, SLEEP_MODE,
SLEEP_AF_MODE and DISCOVERY. According to each type and the NCI
state machine is different (see figure 10 RF Communication State
Machine in NCI specification)
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The nci status byte was ignored. In case of tag reading for example,
if the tag is removed from the antenna there is no way for the upper
layers (aka: stack) to get inform about such event.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

- pr_info in st21nfcb_nci_i2c_disable is not necessary
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Merge tag 'iwlwifi-next-for-john-2014-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

"Grumbach, Emmanuel" <emmanuel.grumbach@intel.com> says:

"I deprecate here -8.ucode since -9 has been published long ago.
Along with that I have a new activity, we have now better
infrastructure for firmware debugging. This will allow to
have configurable probes insides the firmware.
Luca continues his work on NetDetect, this feature is now
complete. All the rest is minor fixes here and there."
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The new ucode package format holds also the usniffer images
(in addition to the operational images and the TLVs).
The driver can load the usniffer image if debug
configuration tells it to.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Until this patch, dumping the monitor data could be done only
for PCIe external (DRAM) mode in 7000 HW family. This patch
allows to pull the monitor data also on other families, and
also to pull the monitor data if an internal buffer is used.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Sometimes there is a need to configure some registers for
setting some FW properties, such as the FW monitor mode
(internal/external). This patch supports setting this for
PCIe mode.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Send all debug-configuration HCMDs that are set in the TLVs
to the FW. This may include HCMDs to configure the FW
monitor and FW log level, for example.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Debug information can be appended to the firmware file. This
information will be used by the driver to enable / disable
debugging features in the firmware.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Interoperability issues were identified and root caused to
the Smart Fifo watermarks. These issues arose with
NetGear R7000. Fix this.

Cc: <stable@vger.kernel.org> [3.14+]
Fixes: 1f3b0ff8 ("iwlwifi: mvm: Add Smart FIFO support")
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Since the commit below, iwldvm sends the FLUSH command to
the firmware. All the devices that use iwldvm have a
firmware that expects the _v3 version of this command,
besides 5150.
5150's latest available firmware still expects a _v2 version
of the FLUSH command.
This means that since the commit below, we had a mismatch for
this specific device only.
This mismatch led to the NMI below:

Loaded firmware version: 8.24.2.2
Start IWL Error Log Dump:
Status: 0x0000004C, count: 5
0x00000004 | NMI_INTERRUPT_WDG
0x000006F4 | uPc
0x000005BA | branchlink1
0x000006F8 | branchlink2
0x000008C2 | interruptlink1
0x00005B02 | interruptlink2
0x00000002 | data1
0x07030000 | data2
0x00000068 | line
0x3E80510C | beacon time
0x728A0EF4 | tsf low
0x0000002A | tsf hi
0x00000000 | time gp1
0x01BDC977 | time gp2
0x00000000 | time gp3
0x00010818 | uCode version
0x00000000 | hw version
0x00484704 | board version
0x00000002 | hcmd
0x2FF23080 | isr0
0x0103E000 | isr1
0x0000001A | isr2
0x1443FCC3 | isr3
0x11800112 | isr4
0x00000068 | isr_pref
0x000000D4 | wait_event
0x00000000 | l2p_control
0x00000007 | l2p_duration
0x00103040 | l2p_mhvalid
0x00000007 | l2p_addr_match
0x00000000 | lmpm_pmg_sel
0x00000000 | timestamp
0x00000200 | flow_handler

This was reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=88961

Cc: <stable@vger.kernel.org>
Fixes: a0855054 ("iwlwifi: dvm: drop non VO frames when flushing")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In 8000 B-step the FW file has changed, but by the time we
know the HW step, the FW file is already requested.

This patch defaults 8000 family to B-step if no HW step is
detected in time. When it can it checks what HW step it
really is (in 8000 family) and if it isn't B-step, the FW
file is released and the A-step file is requested.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Fix the 4165 series name that was called 4265 by mistake.
Signed-off-by: NOren Givon <oren.givon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When switching from UICC to another, the CLF may signals to the Terminal
Host that some existing pipe are cleared for future update.

This notification needs to be "acked" by the Terminal Host with a ANY_OK
message.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

If our terminal connect with other host like UICC, it may create
a pipe with us, the host controller will notify us new pipe
created, after that UICC will open that pipe, if we don't handle
that request, UICC may failed to continue initialize which may
lead to card emulation feature failed to work
Signed-off-by: NArron Wang <arron.wang@intel.com>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

In ndlc_probe function we initialize timers. They are not started.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

As many event with the same id can come from several gates,
it will be easier to manage each of them by gate.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

se_io allows to send apdu over the CLF to the embedded Secure Element.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Some NFC controller using NCI protocols may need a proprietary commands
flow to disable a secure element
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Some NFC controller using NCI protocols may need a proprietary commands
flow to enable a secure element
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>