There are multiple architectures that support CONFIG_DEBUG_RODATA and
CONFIG_SET_MODULE_RONX. These options also now have the ability to be
turned off at runtime. Move these to an architecture independent
location and make these options def_bool y for almost all of those
arches.
Signed-off-by: NLaura Abbott <labbott@redhat.com>
Acked-by: NIngo Molnar <mingo@kernel.org>
Acked-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NKees Cook <keescook@chromium.org>

Enable low-level debugging support for R-Car V2H (r8a7792).
V2H uses SCIF0 for the debug console, like most other R-Car Gen2 SoCs.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The SUN_TOP_CTRL_FAMILY_ID register  is at a fixed absolute address for
all of our supported chips, so utilize its value to determine what the
UARTA base address should be based on the value we read.

Since the code is called both during decompressor when the MMU is off,
and after the MMU has been turned on in the kernel, and we want to do
the lookup only once, we use the same technique as tegra.S and have a
shared storage location between the decompressor and the kernel.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Northstar Plus SoCs (ARCH_BCM_NSP) have the exact same UART location and
properties like the register shift of 0, so make it usable.
Acked-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Add configuration options for the most commonly used UART physical and
virtual addresses to ease the use of DEBUG_LL and earlyprintk.
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

AT91 still uses an offset (0x0100 0000) from the physical address to map
the debug UART. This is unfortunate as for some platforms (sama5d3 and
earlier), it ends up in the PCI zone and PCI is enabled in multi_v7.
Switch to DEBUG_UART_VIRT to solve that.

Tested on sama5d3 and 9g20.
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

DEBUG_HI3716_UART was supposed to be renamed to DEBUG_HIX5HD2_UART, but
accidentally both got left in place, which results in a build error when
CONFIG_DEBUG_UART_PHYS is not set as it should be.

This removes the old symbol.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: 12aae309 ("ARM: debug: Rename Hi3716 to HIX5HD2")
Acked-by: NWei Xu <xuwei5@hisilicon.com>

Some SoCs use a Palmchip BK-310x UART which is mostly 16550 compatible
but with a different register layout. While this UART has previously
only been supported in MIPS based chips (Alchemy, Ralink), the ARM based
SMP87xx series from Sigma Designs also uses it.

This patch allows the debug console to work with this type of UART.
Signed-off-by: NMans Rullgard <mans@mansr.com>
Signed-off-by: NMarc Gonzalez <marc_gonzalez@sigmadesigns.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NKevin Hilman <khilman@baylibre.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

During my randconfig build testing, I found that a kernel with
DEBUG_AT91_UART and ARCH_BCM_63XX fails to build:

arch/arm/include/debug/at91.S:18:0: error: "CONFIG_DEBUG_UART_VIRT" redefined [-Werror]

It turns out that the DEBUG_UART_BCM63XX option is enabled whenever
the ARCH_BCM_63XX is, and that breaks multiplatform kernels because
we then end up using the UART address from BCM63XX rather than the
one we actually configured (if any).

This changes the BCM63XX options to only have one Kconfig option,
and only enable that if the user explicitly turns it on.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: b51312be ("ARM: BCM63XX: add low-level UART debug support")
Cc: stable@vger.kernel.org

Let all the archs that implement devmem_is_allowed() opt-in to a common
definition of CONFIG_STRICT_DEVM in lib/Kconfig.debug.

Cc: Kees Cook <keescook@chromium.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
[heiko: drop 'default y' for s390]
Acked-by: NIngo Molnar <mingo@redhat.com>
Suggested-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

This should be a complete port of bcm2835 functionality to bcm2836
(Raspberry Pi 2).
Signed-off-by: NEric Anholt <eric@anholt.net>

I accidentally move the DEBUG_LL_UART_EFM32 option when sorting all
other options alphanumerically, but it belongs into the same group
as DEBUG_LL_UART_8250 and DEBUG_LL_UART_PL01X.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: 1dc93416 ("ARM: debug-ll: reorder Kconfig alphanumerically")

The file has gotten a little out of sync, as platforms got
added in the wrong place, or have been renamed. This moves
the options around, but should not change any functionality.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Footbridge has two debug ports that are handled a bit differently:

The 8250 port uses the normal debug/8250.S implementation that is shared
with a lot of other platforms, but it relies on the DEBUG_UART_8250
option to be turned on automatically instead of being selected by
DEBUG_FOOTBRIDGE_COM1 as we do for most other platforms. I'm changing
this to use a 'select' and change the dependency to the debug symbol
rather than the platform symbol for consistency.

The DC21285 UART has a separate top-level option, and relies on
the traditional include/mach/debug-macro.S method. With the s3c64xx
multiplatform series queued up for 4.5, it is now the last one that does
this, so by moving this file to include/debug/dc21285.S, we can get
all platforms to do things the same way.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

LPC32xx can not yet be configured in a multiplatform kernel, but
if we ever get there, enabling one of the LPC32xx platforms
while trying to use DEBUG_LL for another platform can default to
the wrong UART address, as the options are purely based on the
architecture being enabled or not.

This changes the logic to use the LPC32xx default addresses only
if we have also picked the respective Kconfig symbols introduced
here.

While we're at it, this also reorders the virtual address as
it should be.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NVladimir Zapolskiy <vz@mleia.com>

Gemini can not yet be configured in a multiplatform kernel, but
if we ever get there, enabling one of the gemini platforms
while trying to use DEBUG_LL for another platform can default to
the wrong UART address, as the options are purely based on the
architecture being enabled or not.

This changes the logic to use the gemini default addresses and
the flow control settings only if we have also picked the respective
Kconfig symbols introduced here.

While we're at it, this also reorders the virtual address as
it should be.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NHans Ulli Kroll <ulli.kroll@googlemail.com>

Enabling one of the integrator platforms in a multiplatform kernel
while trying to use DEBUG_LL for another platform can default to
the wrong UART address, as the options are purely based on the
architecture being enabled or not.

This changes the logic to use the integrator default addresses only
if we have also picked the respective Kconfig symbols introduced
here. Versatile is not yet part of multiplatform, but hopefully
soon will be, so we do the same change for versatile as well.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Enabling one of the SPEAr platforms in a multiplatform kernel
while trying to use DEBUG_LL for another platform can default to
the wrong UART address, as the options are purely based on the
architecture being enabled or not.

This changes the logic to use the SPEAr default addresses only
if we have also picked the respective Kconfig symbols introduced
here.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This makes ep93xx debug-ll handling more consistent with the other
platforms, by adding a separate Kconfig symbol for it that
in turn selects the standard DEBUG_UART_PL01X symbol.

We still have to pick a physical address even if DEBUG_LL is disabled
here, because the EP93xx uncompress output code uses
CONFIG_DEBUG_UART_PHYS. If we ever move to multiplatform support,
this can go away.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

As we are moving dove/mv78xx0/orion into multiplatform, the debug-ll
configuration options for these platforms are conflicting with the
multiplatform configuration: enabling one of those platforms sometimes
changes the default addresses to the ones used on one of them, rather
than the one that was selected in Kconfig.

This changes the configuration so we share the physical address
configuration with mach-mvebu.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

We may have multiple platforms enabled and also DEBUG_LL
configured for one of them. However if we enable ARCH_KEYSTONE,
we default to using 32-bit UART access independent of which
platform we are actually using, which can be confusing.

This changes the logic so the 32-bit default gets only
used by default if we actually configure the keystone
UART, as opposed to picking some other 8250 setting on
a kernel that has keystone support enabled.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The uart on s3c64xx is essentially the same as on s3c24xx,
so we can share a single assembler file. However, the addresses
are different, and we need to add the respective Kconfig magic
to get the right addresses.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Instead of having to add a new configuration option each time support for
new SoC is added, use CONFIG_DEBUG_UART_PHYS. For now,
CONFIG_DEBUG_UART_VIRT is automatically computed.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

With Bock-W, the last legacy platform has been removed.
Signed-off-by: NUlrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Nby: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add Kconfig entries, header file changes and addition to the documentation.
The early debug infrastructure is also added for easy development.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Enable low-level debug support for i.MX6UL by adding the
debug port definitions for the SoC.
Singed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

randconfig testing reveals that DEBUG_SET_MODULE_RONX needs to depend on
MMU otherwise these build errors are observed:

kernel/built-in.o: In function `set_section_ro_nx':
kernel/module.c:1738: undefined reference to `set_memory_nx'
kernel/built-in.o: In function `set_page_attributes':
kernel/module.c:1709: undefined reference to `set_memory_ro'

This is because the pageattr functions are not built for !MMU configs as
they don't have page tables.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add low level uart debug support for imx7d
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NBai Ping <b51503@freescale.com>
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

It's obviously pointless to dump page tables when the MMU is disabled,
and even trying to build this code results in numerous build errors
like these:

../arch/arm/mm/dump.c:56:11: error: 'L_PTE_USER' undeclared here (not in a function)
   .mask = L_PTE_USER,
           ^
../arch/arm/mm/dump.c:61:11: error: 'L_PTE_RDONLY' undeclared here (not in a function)
   .mask = L_PTE_RDONLY,
           ^
../arch/arm/mm/dump.c:66:11: error: 'L_PTE_XN' undeclared here (not in a function)
   .mask = L_PTE_XN,
           ^
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Use the new config symbol ARM_SINGLE_ARMV7M which groups config
symbols used by modern ARMv7-M platforms. This allows supporting
multiple ARMv7-M platforms in one kernel image. However, a common
kernel image requires the combined platforms to share the same
main memory layout to be bootable.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NJoachim Eastwood <manabian@gmail.com>
Acked-by: NMaxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This introduces a new top level config symbol ARM_SINGLE_ARMV7M
for non-MMU, ARMv7-M platforms. It also support multiple ARMv7-M
platforms in one kernel image since the cores share the same
basic memory layout and interrupt controller. However, this works
only if the combined platforms also have a similar (main) memory
layout.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Using a dedicated symbol for low-level debugging instead of the
arch symbol will make this platform play nice when enabled on a
kernel that supports multiple platforms.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Use the UART0 peripheral for low level debug. Only the UART port 0 is
currently supported.
Signed-off-by: NJun Nie <jun.nie@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Add support for NXP's LPC18xx (Cortex-M3) and LPC43xx (Cortex-M4)
SoCs. These SoCs are NXP's high preformance MCU line and can run at
clock speeds up to 180 MHz for LPC18xx and 204 MHz for LPC43xx.

LPC43xx is more or less a LPC18xx with a Cortex-M4F core and a few
extra peripherals. The LPC43xx series also features one or two
Cortex-M0 cores that can be used to offload the main M4 core.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Reviewed-by: NEzequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Add support for hardware uart1 for earlyprintk support on Arria10 devkit.
Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>

Keeping drivers related to HW tracing on ARM, i.e coresight,
under "drivers/coresight" doesn't make sense when other
architectures start rolling out technologies of the same
nature.

As such creating a new "drivers/hwtracing" directory where all
drivers of the same kind can reside, reducing namespace
pollution under "drivers/".
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Most CoreSight blocks are 64-bit ready.  As such move configuration
entries from "arch/arm/Kconfig.config" to the driver's subdirectory
and source the newly created Kconfig from architecture specific
Kconfig.debug files.
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The maintainers for mach-msm no longer have any plans to support
or test the platforms supported by this architecture[1]. Most likely
there aren't any active users of this code anyway, so let's
delete it.

[1] http://lkml.kernel.org/r/20150307031212.GA8434@fifo99.com
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NKumar Gala <galak@codeaurora.org>

Alpine platform includes UART8250 that can be used for early prints.
Signed-off-by: NSaeed Bishara <saeed@annapurnalabs.com>
Signed-off-by: NTsahee Zidenberg <tsahee@annapurnalabs.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Remove the stray closing parenthesis in the config description for the
DEBUG_RCAR_GEN2_SCIF0 option.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>