I don't think there's enough value in the fact of a bridge window
being disabled to justify cluttering the dmesg log with it.
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

decode_bar() and pci_calc_resource_flags() both looked at the PCI BAR
type information, and it's simpler to just do it all in one place.

decode_bar() sets IORESOURCE_IO, IORESOURCE_MEM, and IORESOURCE_MEM_64
as appropriate, so res->flags contains all the information pci_bar_type
does, so we don't need to test the pci_bar_type return value.

decode_bar() used to return pci_bar_type, which we no longer need.  We
can simplify it a bit by returning the struct resource flags rather than
updating them internally.

In pci_update_resource(), there's no need to decode the BAR type bits
again; we can just test for IORESOURCE_MEM_64 directly.
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This fixes a minor regression where broken PCI devices that use the
reserved "11" memory BAR type worked before e354597c but not after.

The low four bits of a memory BAR are "PTT0" where P=1 for prefetchable
BARs, and TT is as follows:

  00  32-bit BAR, anywhere in lower 4GB
  01  anywhere below 1MB (reserved as of PCI 2.2)
  10  64-bit BAR
  11  reserved

Prior to e354597c, we treated "0100" as a 64-bit BAR and all others,
including prefetchable 64-bit BARs ("1100") as 32-bit BARs.  The e354597c
fix, which appeared in 2.6.28, treats "x1x0" as 64-bit BARs, so the
reserved "x110" types are treated as 64-bit instead of 32-bit.

This patch returns to treating the reserved "11" type as a 32-bit BAR and
adds a warning if we see it.

It also logs a note if we see a 1M BAR.  This is not a warning, because
such hardware conforms to pre-PCI 2.2 spec, but I think it's worth noting
because Linux ignores the 1M restriction if it ever has to assign the BAR.

CC: Peter Chubb <peterc@gelato.unsw.edu.au>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=35952Reported-by: NJan Zwiegers <jan@radicalsystems.co.za>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

When hot-plugging a root bridge, we always prevent assigning a bus number
that already exists. This makes sure we don't step over an existing bus.
But sometimes we only remove PCI device in PCI hieratchy of OS, i,e.

echo 1 > /sys/bus/pci/devices/.../remove

but actually don't hotplug this device out the platform, so in this case
we still should re-scan this bus to enumerate this device when re-scanning
PCI again.
Signed-off-by: NTiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

IO_SPACE_LIMIT is currently used in two ways:

1) As a way to mask I/O port values read out of PCI base address
   registers.  This value should be 64-bit.

2) As a value which is the upper limit for all I/O "ports" in the
   system.

On sparc64 we store the full 64-bit physical I/O address in the
resources.  For this reason we define IO_SPACE_LIMIT at a 64-bit
"all 1's".

This is the right value to use for ioport_resource.end and for the
check made in drivers/pcmcia/rsrc_nonstatic.c:adjust_io().

But in driver/pci/probe.c:__pci_read_base() we mask this against
a "u32" variable and thus get the following warning:

drivers/pci/probe.c: In function ¡__pci_read_base¢:
drivers/pci/probe.c:207: warning: large integer implicitly truncated to unsigned type

Fix this by using an explicit "u32" cast.

I considered changing sparc64 to define a 32-bit "all 1's" like
most other systems do, but this wouldn't work because the checks
in PCMCIA's rsrc_nonstatic.c would no longer be right since they
are testing against fully formed 64-bit resources.  As described
above, on sparc64 such resources will hold full 64-bit physical
I/O addresses, not bus-centric 32-bit ones.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Requested by Greg KH to fix a race condition in the creating of PCI bus
cpuaffinity files.
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

After remove the device from /sys, we have to rescan all or
find out the bridge and access /sys../device/rescan there.

this patch add /sys/.../pci_bus/.../rescan. So user can rescan more easy.
that is more clean and easy to understand.

like after remove 0000:c4:00.0, you can rescan 0000:c4 directly.

-v2: According to Jesse, use function instead of exposing attr, so could hide
	#ifdef in header file.
     also add code to remove rescan file in remove path.
-v3: GregKH pointed out that we should use dev_attrs to avoid racing.
     So add pcibus_attrs and make it to be member of pcibus_attrs.
-v4: Change name to pcibus_dev_attrs according to GregKH
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

pci_add_new_bus() calls pci_alloc_child_bus() which calls pci_alloc_bus()
that allocates memory dynamically with kzalloc(). The return value of
kzalloc() is the pointer that's eventually returned from
pci_add_new_bus(), so since kzalloc() can fail and return NULL so can
pci_add_new_bus(). Thus we may end up dereferencing a NULL pointer in
drivers/pci/probe.c::pci_scan_bridge(). Seems to me we should test for
this and bail out if it happens rather than crashing.
Also removed some trailing whitespace that bugged me while looking at
this.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Previously we had to have CONFIG_PCI_DEBUG=y or CONFIG_DYNAMIC_DEBUG=y
to turn on this printk, but I think the IDs are valuable enough that it's
worth putting them in the log always.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

It is a known issue that mmio decoding shall be disabled while doing PCI
bar sizing. Host bridge and other devices (PCI PIC) shall be excluded for
certain platforms. This patch mainly comes from Mathew Willcox's
patch in http://kerneltrap.org/mailarchive/linux-kernel/2007/9/13/258969.

A new flag bit "mmio_alway_on" is added to pci_dev with the intention that
devices with their mmio decoding cannot be disabled during BAR sizing shall
have this bit set, preferrablly in their quirks.

Without this patch, Intel Moorestown platform graphics unit will be
corrupted during bar sizing activities.
Signed-off-by: NJacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Now, a dedicated HEST tabling parsing code is used for PCIE AER
firmware_first setup. It is rebased on general HEST tabling parsing
code of APEI. The firmware_first setup code is moved from PCI core to
AER driver too, because it is only AER related.
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Reviewed-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

This reverts c519a5a7.  That change added a warning about devices that
didn't respond correctly when sizing BARs, which helped diagnose broken
devices.  But the test wasn't specific enough, so it also complained about
working devices with zero-size BARs, e.g.,
https://bugzilla.kernel.org/show_bug.cgi?id=15822Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

If we can tell that a device isn't working correctly, we should tell
the user to make debugging easier.  Otherwise, it can take a lot of
work to determine whether the problem is in the driver, PCMCIA, PCI,
hardware, etc., as in http://bugzilla.kernel.org/show_bug.cgi?id=12006Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

No functional change; this just tweaks the changes from 349e1823a405
so the new printks for disabled PCI-to-PCI bridge windows match the
ones for the enabled windows.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
CC: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

No functional change; just add names for the primary/secondary/subordinate
bus numbers read from config space rather than repeatedly masking/shifting.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Set power.async_suspend for all PCI devices and PCIe port services,
so that they can be suspended and resumed in parallel with other
devices they don't depend on in a known way (i.e. devices which are
not their parents or children).

This only affects the "regular" suspend and resume stages, which
means in particular that the restoration of the PCI devices' standard
configuration registers during resume will still be carried out
synchronously (at the "early" resume stage).
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Previously we used a table of size PCI_BUS_NUM_RESOURCES (16) for resources
forwarded to a bus by its upstream bridge.  We've increased this size
several times when the table overflowed.

But there's no good limit on the number of resources because host bridges
and subtractive decode bridges can forward any number of ranges to their
secondary buses.

This patch reduces the table to only PCI_BRIDGE_RESOURCE_NUM (4) entries,
which corresponds to the number of windows a PCI-to-PCI (3) or CardBus (4)
bridge can positively decode.  Any additional resources, e.g., PCI host
bridge windows or subtractively-decoded regions, are kept in a list.

I'd prefer a single list rather than this split table/list approach, but
that requires simultaneous changes to every architecture.  This approach
only requires immediate changes where we set up (a) host bridges with more
than four windows and (b) subtractive-decode P2P bridges, and we can
incrementally change other architectures to use the list.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

No functional change; this fills in the bus subtractive decode resources
after reading the bridge window information rather than before.  Also,
print out the subtractive decode resources as we already do for the
positive decode windows.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

No functional change; this breaks up pci_read_bridge_bases() into separate
pieces for the I/O, memory, and prefetchable memory windows, similar to how
Yinghai recently split up pci_setup_bridge() in 68e84ff3bdc.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

We already track unassigned resources in struct resource, and this
prevents us from overwriting resource flags and info in the unassigned
case.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Yinghai pointed out that the new pci_scan_slot() crashes when called
on an ARI-capable slot that is empty.  Fix this by exiting early from
pci_scan_slot if there is no device in the slot.

Also make next_ari_func() robust against devices not existing in case
the ARI capability is corrupt.  ARI also requires that the devices be
listed in order, so if we find a function listed that is out of order,
stop scanning to prevent loops.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Add the 8.0 GT/s speed.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Take advantage of some gaps in the table to fit in support for AGP speeds.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Both PCIe and PCI-X bridges report their secondary bus speed in their
respective capabilities.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Move the max_bus_speed and cur_bus_speed into the pci_bus.  Expose the
values through the PCI slot driver instead of the hotplug slot driver.
Update all the hotplug drivers to use the pci_bus instead of their own
data structures.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The Alternate Routing-ID Interpretation capability allows a single device
to have up to 256 functions.  They can be populated sparsely, so the
current technique of scanning every eighth function is not guaranteed
to find them all.  By introducing a 'next_fn' function pointer, we can
use the linked list of functions in the ARI capability to scan all the
functions which exist.

We can then speed up the pci_scan_slot by skipping the scan of subsequent
devfns for PCIe devices which are the direct children of Root Ports or
Downstream Ports.  These devices are only permitted to implement device
0, unless they are ARI devices, in which case they'll be scanned by the
ARI code above.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

We are missing these when building the pci_dev from scratch off
the Open Firmware device-tree
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Commit ae21ee65 "PCI: acs p2p upsteram
forwarding enabling" doesn't actually enable ACS.

Add a function to pci core to allow an IOMMU to request that ACS
be enabled.  The existing mechanism of using iommu_found() in the pci
core to know when ACS should be enabled doesn't actually work due to
initialization order;  iommu has only been detected not initialized.

Have Intel and AMD IOMMUs request ACS, and Xen does as well during early
init of dom0.

Cc: Allen Kay <allen.m.kay@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: NChris Wright <chrisw@sous-sol.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Use pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in PCI core code. This avoids unnecessary search in PCI
configuration space.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

There are a lot of codes that searches PCI express capability offset
in the PCI configuration space using pci_find_capability(). Caching it
in the struct pci_dev will reduce unncecessary search. This patch adds
an additional 'pcie_cap' fields into struct pci_dev, which is
initialized at pci device scan time (in set_pcie_port_type()).
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This makes PCI resource management messages more consistent and adds a few
new messages to aid debugging.

Whenever we assign resources to a device, update a BAR, or change a
bridge aperture, it's worth noting it.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Since we have a struct device, we might as well use dev_printk.  Note that
both pr_debug() and dev_dbg() are completely compiled out unless DEBUG or
DYNAMIC_DEBUG is defined.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Jesse accidentally applied v1 [1] of the patchset instead of v2 [2].  This
is the diff between v1 and v2.

The changes in this patch are:
    - tidied vsprintf stack buffer to shrink and compute size more
      accurately
    - use %pR for decoding and %pr for "raw" (with type and flags) instead
      of adding %pRt and %pRf

[1] http://lkml.org/lkml/2009/10/6/491
[2] http://lkml.org/lkml/2009/10/13/441Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Change to populate the subsystem vendor and subsytem device IDs for
PCI-PCI bridges that implement the PCI Subsystem Vendor ID capability.
Previously bridges left subsystem vendor IDs unpopulated.
Signed-off-by: NGabe Black <gabe.black@ni.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Feedback from Hidetoshi Seto and Kenji Kaneshige incorporated.  This
correctly handles PCI-X bridges, PCIe root ports and endpoints, and
prints debug messages when invalid/reserved types are found in the
HEST.  PCI devices not in domain/segment 0 are not represented in
HEST, thus will be ignored.

Today, the PCIe Advanced Error Reporting (AER) driver attaches itself
to every PCIe root port for which BIOS reports it should, via ACPI
_OSC.

However, _OSC alone is insufficient for newer BIOSes.  Part of ACPI
4.0 is the new APEI (ACPI Platform Error Interfaces) which is a way
for OS and BIOS to handshake over which errors for which components
each will handle.  One table in ACPI 4.0 is the Hardware Error Source
Table (HEST), where BIOS can define that errors for certain PCIe
devices (or all devices), should be handled by BIOS ("Firmware First
mode"), rather than be handled by the OS.

Dell PowerEdge 11G server BIOS defines Firmware First mode in HEST, so
that it may manage such errors, log them to the System Event Log, and
possibly take other actions.  The aer driver should honor this, and
not attach itself to devices noted as such.

Furthermore, Kenji Kaneshige reminded us to disallow changing the AER
registers when respecting Firmware First mode.  Platform firmware is
expected to manage these, and if changes to them are allowed, it could
break that firmware's behavior.

The HEST parsing code may be replaced in the future by a more
feature-rich implementation.  This patch provides the minimum needed
to prevent breakage until that implementation is available.
Reviewed-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reviewed-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NMatt Domsch <Matt_Domsch@dell.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

When probing for ROM BAR size, we should not change bits 1:10 in this
BAR, because these bits are marked as "reserved for future use" in PCI
spec, so changing them might have side effects.

No such issue for I/O or memory, as there is an implementation note in
PCI spec which explicitly allows writing 0xfffffffff there.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This patch is predicated on Jeremy's patch in include/xen/xen.h.  It'll
prevent ACS init unless the platform has both an IOMMU and we're running
as dom0.
Signed-off-by: NAllen Kay <allen.m.kay@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Note: dom0 checking in v4 has been separated out into 2/2.

This patch enables P2P upstream forwarding in ACS capable PCIe switches.
It solves two potential problems in virtualization environment where a PCIe
device is assigned to a guest domain using a HW iommu such as VT-d:

1) Unintentional failure caused by guest physical address programmed
   into the device's DMA that happens to match the memory address range
   of other downstream ports in the same PCIe switch.  This causes the PCI
   transaction to go to the matching downstream port instead of go to the
   root complex to get translated by VT-d as it should be.

2) Malicious guest software intentionally attacks another downstream
   PCIe device by programming the DMA address into the assigned device
   that matches memory address range of the downstream PCIe port.

We are in process of implementing device filtering software in KVM/XEN
management software to allow device assignment of PCIe devices behind a PCIe
switch only if it has ACS capability and with the P2P upstream forwarding bits
enabled.  This patch is intended to work for both KVM and Xen environments.
Signed-off-by: NAllen Kay <allen.m.kay@intel.com>
Reviewed-by: NMathew Wilcox <willy@linux.intel.com>
Reviewed-by: NChris Wright <chris@sous-sol.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This uses %pRt to print additional resource information (type, size,
prefetchability, etc.) consistently.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Some PCI devices fail if their standard configuration registers are
restored twice in a row.  Prevent this from happening by making
pci_restore_state() clear the saved_state flag of the device right
after the device's standard configuration registers have been
populated with the previously saved values.

Simplify PCI PM callbacks by removing the direct clearing of
state_saved from them, as it shouldn't be necessary any more (except
in pci_pm_thaw(), where it has to be cleared, so that the values saved
during the "freeze" phase of hibernation are not used later by mistake).
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>