In f8b45b74 ("i40e/i40evf: Use build_skb to build frames")
i40e_build_skb updates the page_offset field with an incorrect offset,
which can lead to data corruption. This patch updates page_offset
correctly, by properly setting truesize.

Note that the bug only appears on architectures where PAGE_SIZE is
8192 or larger.

Fixes: f8b45b74 ("i40e/i40evf: Use build_skb to build frames")
Signed-off-by: NBjörn Töpel <bjorn.topel@intel.com>
Acked-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit 0da36b97 ("i40e: use DECLARE_BITMAP for state fields")
introduced changes in the way i40e works with state flags converting
them to bitmaps using kernel bitmap API. This change introduced a
regression due to a mistaken substitution using __I40E_VSI_DOWN instead
of __I40E_DOWN when testing state of a PF at i40e_reset_subtask()
function. This caused a flood in the kernel log with the follow message:

[49.013] i40e 0002:01:00.0: bad reset request 0x00000020

Commit d19cb64b ("i40e: separate PF and VSI state flags")
also introduced some misuse of the VSI and PF flags, so both could be
considered as the offenders.

This patch simply fixes the flags where it makes sense by changing
__I40E_VSI_DOWN to __I40E_DOWN.

Fixes: 0da36b97 ("i40e: use DECLARE_BITMAP for state fields")
Fixes: d19cb64b ("i40e: separate PF and VSI state flags")
Reviewed-by: N"Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: N"Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Sending host command with CMD_WANT_SKB flag demands the release of the
response buffer with iwl_free_resp function.
The patch adds the memory release in all the relevant places
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In a previous commit, we removed support for API versions earlier than
22 for these NICs.  By mistake, the *_UCODE_API_MIN definitions were
set to 17.  Fix that.

Fixes: 4b87e5af ("iwlwifi: remove support for fw older than -17 and -22")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Clear the struct so that all reserved fields are zero when we
send the struct down to the device.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The iwl_mvm_remove_sta_key() function handles removing a key when the
sta doesn't exist anymore.  Mistakenly, this was changed to return an
error while fixing another bug.

If the mvm_sta doesn't exist, we continue normally, but just don't try
to remove the igtk key.

Fixes: cd4d23c1 ("iwlwifi: mvm: Fix removal of IGTK")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We only need to handle d0i3 entry and exit during suspend resume if
system_pm is set to IWL_PLAT_PM_MODE_D0I3, otherwise d0i3 entry
failures will cause suspend to fail.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=194791Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When we want to stop the recording of the firmware debug
and restart it later without reloading the firmware we
don't need to resend the configuration that comes with
host commands.
Sending those commands confused the hardware and led to
an NMI 0x66.

Change the flow as following:
* read the relevant registers (DBGC_IN_SAMPLE, DBGC_OUT_CTRL)
* clear those registers
* wait for the hardware to complete its write to the buffer
* get the data
* restore the value of those registers (to restart the
  recording)

For early start (where the configuration is already
compiled in the firmware), we don't need to set those
registers after the firmware has been loaded, but only
when we want to restart the recording without having
restarted the firmware.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The ucode_loaded check should be under the mutex, since it can
otherwise change state after we looked at it and before we got
the mutex. Fix that.

Fixes: 5c89e7bc ("iwlwifi: mvm: add registration to cooling device")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Allow working IBSS also when working in DQA mode.
This is done by setting it to treat the queues the
same as a BSS AP treats the queues.

Fixes: 7948b873 ("iwlwifi: mvm: enable dynamic queue allocation mode")
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

During d0i3 flow we flush all the queue except from the command queue.
Currently, in this flow the command queue is hard coded to 9.
In DQA the command queue number has changed from 9 to 0.
Fix that.

This fixes a problem in runtime PM resume flow.

Fixes: 097129c9 ("iwlwifi: mvm: move cmd queue to be #0 in dqa mode")
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Up until now, the driver was comparing the rate reported by the FW and
the rate of the latest LQ command to avoid processing data belonging
to the old LQ command. Recently, FW changed the meaning of the initial
rate field in tx response and it holds the actual rate (which is not
necessarily the initial rate of LQ's rate table). Use instead LQ cmd
color to be able to filter out tx responses/BA notifications which
where sent during earlier LQ commands' time frame.

This fixes some throughput degradation in noisy environments.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The Granular QoS per VF feature must be enabled in FW before it can be
used.

Thus, the driver cannot modify a QP's qos_vport value (via the UPDATE_QP FW
command) if the feature has not been enabled -- the FW returns an error if
this is attempted.

Fixes: 08068cd5 ("net/mlx4: Added qos_vport QP configuration in VST mode")
Signed-off-by: NIdo Shamay <idos@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix kernel-doc warnings (typo) in drivers/net/phy/phy.c:

..//drivers/net/phy/phy.c:259: warning: No description found for parameter 'features'
..//drivers/net/phy/phy.c:259: warning: Excess function parameter 'feature' description in 'phy_lookup_setting'
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Our previous patch (cited below) introduced a regression
for RAW Eth QPs.

Fix it by checking if the QP number provided by user-space
exists, hence allowing steering rules to be added for valid
QPs only.

Fixes: 89c55768 ("net/mlx4_en: Avoid adding steering rules with invalid ring")
Reported-by: NOr Gerlitz <gerlitz.or@gmail.com>
Signed-off-by: NTalat Batheesh <talatb@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Acked-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 9b4437a5 ("geneve: Unify LWT and netdev handling.")
when using COLLECT_METADATA geneve devices are created with too small of
a needed_headroom and too large of a max_mtu. This is because
ip_tunnel_info_af() is not valid with the device level info when using
COLLECT_METADATA and we mistakenly fall into the IPv4 case.

For COLLECT_METADATA, always use the worst case of ipv6 since both
sockets are created.

Fixes: 9b4437a5 ("geneve: Unify LWT and netdev handling.")
Signed-off-by: NEric Garver <e@erig.me>
Acked-by: NPravin B Shelar <pshelar@ovn.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

xgbe_map_rx_buffer is rather confused about what PAGE_ALLOC_COSTLY_ORDER
means. It uses PAGE_ALLOC_COSTLY_ORDER-1 assuming that
PAGE_ALLOC_COSTLY_ORDER is the first costly order which is not the case
actually because orders larger than that are costly. And even that
applies only to sleeping allocations which is not the case here. We
simply do not perform any costly operations like reclaim or compaction
for those. Simplify the code by dropping the order calculation and use
PAGE_ALLOC_COSTLY_ORDER directly.
Signed-off-by: NMichal Hocko <mhocko@suse.com>
Acked-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use software polling (PHY_POLL) to check for link state changes instead
of relying on the EMAC's hardware polling feature.  Some PHY drivers
are unable to get a functioning link because the HW polling is not
robust enough.

The EMAC is able to poll the PHY on the MDIO bus looking for link state
changes (via the Link Status bit in the Status Register at address 0x1).
When the link state changes, the EMAC triggers an interrupt and tells the
driver what the new state is.  The feature eliminates the need for
software to poll the MDIO bus.

Unfortunately, this feature is incompatible with phylib, because it
ignores everything that the PHY core and PHY drivers are trying to do.
In particular:

1. It assumes a compatible register set, so PHYs with different registers
   may not work.

2. It doesn't allow for hardware errata that have work-arounds implemented
   in the PHY driver.

3. It doesn't support multiple register pages. If the PHY core switches
   the register set to another page, the EMAC won't know the page has
   changed and will still attempt to read the same PHY register.

4. It only checks the copper side of the link, not the SGMII side.  Some
   PHY drivers (e.g. at803x) may also check the SGMII side, and
   report the link as not ready during autonegotiation if the SGMII link
   is still down.  Phylib then waits for another interrupt to query
   the PHY again, but the EMAC won't send another interrupt because it
   thinks the link is up.

Cc: stable@vger.kernel.org # 4.11.x
Tested-by: NManoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit d85b758f ("virtio_net: fix support for small rings")
was supposed to increase the buffer size for small rings but had an
unintentional side effect of decreasing it for large rings. This seems
to break some setups - it's not yet clear why, but increasing buffer
size back to what it was before helps.

Fixes: d85b758f ("virtio_net: fix support for small rings")
Reported-by: NMikulas Patocka <mpatocka@redhat.com>
Reported-by: N"J. Bruce Fields" <bfields@fieldses.org>
Tested-by: NMikulas Patocka <mpatocka@redhat.com>
Tested-by: N"J. Bruce Fields" <bfields@fieldses.org>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Qlogic's 82xx series adapter doesn't support
tunnel offloads, driver incorrectly assumes that it is
supported and causes firmware hang while running tunnel IO.

This patch fixes this by not advertising tunnel offloads
for 82xx adapters.
Signed-off-by: NManish Chopra <manish.chopra@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding a vxlan interface to a socket isn't symmetrical, while adding
is done in vxlan_open() the deletion is done in vxlan_dellink().
This can cause a use-after-free error when we close the vxlan
interface before deleting it.

We add vxlan_vs_del_dev() to match vxlan_vs_add_dev() and call
it from vxlan_stop() to match the call from vxlan_open().

Fixes: 56ef9c90 ("vxlan: Move socket initialization to within rtnl scope")
Acked-by: NJiri Benc <jbenc@redhat.com>
Tested-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NMark Bloch <markb@mellanox.com>
Acked-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The original author left the project and so far has not
responded to emails sent to the listed address.
Signed-off-by: NJohn Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix NETDEV WATCHDOG timeout on startup by adding missing register
writes that properly setup SGMII.
Signed-off-by: NThor Thayer <thor.thayer@linux.intel.com>
Acked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Take uld mutex to avoid race between cxgb_up() and
cxgb4_register_uld() to enable napi for the same uld
queue.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On SYSTEMPORT Lite, since we have the main interrupt source in the first
cell, the second cell is the Wake-on-LAN interrupt, yet the code was not
properly updated to fetch the second cell, and instead looked at the
third and non-existing cell for Wake-on-LAN.

Fixes: 44a4524c ("net: systemport: Add support for SYSTEMPORT Lite")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These bits seem to be lost after a suspend/resume cycle so just set them
again. Do this by splitting the handling of these bits into a function
that is also called on resume.

This patch fixes ethernet suspend/resume on imx6ul-14x14-evk boards.
Signed-off-by: NLeonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver may sleep under a read spin lock, and the function call path is:
send_socklist (acquire the lock by read_lock)
  skb_copy(GFP_KERNEL) --> may sleep

To fix it, the "GFP_KERNEL" is replaced with "GFP_ATOMIC".
Signed-off-by: NJia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit 0c1d70af ("net: use dst_cache for vxlan device"),
cached dst entries could be leaked when more than one remote was
present for a given vxlan_fdb entry, causing subsequent netns
operations to block indefinitely and "unregister_netdevice: waiting
for lo to become free." messages to appear in the kernel log.

Fix by properly releasing cached dst and freeing resources in this
case.

Fixes: 0c1d70af ("net: use dst_cache for vxlan device")
Signed-off-by: NLance Richardson <lrichard@redhat.com>
Acked-by: NPaolo Abeni <pabeni@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Apparently multi-cos isn't working for bnx2x quite some time -
driver implements ndo_select_queue() to allow queue-selection
for FCoE, but the regular L2 flow would cause it to modulo the
fallback's result by the number of queues.
The fallback would return a queue matching the needed tc
[via __skb_tx_hash()], but since the modulo is by the number of TSS
queues where number of TCs is not accounted, transmission would always
be done by a queue configured into using TC0.

Fixes: ada7c19e ("bnx2x: use XPS if possible for bnx2x_select_queue instead of pure hash")
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change t4fw_version.h to update latest firmware version
number to 1.16.45.0.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver may sleep under a write spin lock, and the function
call path is:
qlcnic_82xx_hw_write_wx_2M (acquire the lock by write_lock_irqsave)
  crb_win_lock
    qlcnic_pcie_sem_lock
      usleep_range
qlcnic_82xx_hw_read_wx_2M (acquire the lock by write_lock_irqsave)
  crb_win_lock
    qlcnic_pcie_sem_lock
      usleep_range

To fix it, the usleep_range is replaced with udelay.
Signed-off-by: NJia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For SDIO the alignment requirement for transfers from device to host
is configured in firmware. This configuration is limited to minimum
of 4-byte alignment. However, this is not correct for platforms using
64-bit DMA when the minimum alignment should be 8 bytes. This issue
appeared when the ALIGNMENT definition was set according the DMA
configuration. The configuration in firmware was not using that macro
defintion, but a hardcoded value of 4. Hence the driver reported
alignment failures for data coming from the device and causing
transfers to fail.

Fixes: 6e84ab60 ("brcmfmac: properly align buffers on certain platforms
Reported-by: NHans de Goede <hdegoede@redhat.com>
Tested-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NHante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The driver may sleep under a spin lock, the function call path is:
isdn_ppp_mp_receive (acquire the lock)
  isdn_ppp_mp_reassembly
    isdn_ppp_push_higher
      isdn_ppp_decompress
        isdn_ppp_ccp_reset_trans
          isdn_ppp_ccp_reset_alloc_state
            kzalloc(GFP_KERNEL) --> may sleep

To fixed it, the "GFP_KERNEL" is replaced with "GFP_ATOMIC".
Signed-off-by: NJia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add NULL check before dereferencing pointer _id_ in order to avoid
a potential NULL pointer dereference.

Addresses-Coverity-ID: 1397995
Signed-off-by: NGustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Auto-loading of the Marvell DSA driver has stopped working with recent
kernels.  This seems to be due to the change of binding for DSA devices,
moving them from the platform bus to the MDIO bus.

In order for module auto-loading to work, we need to provide a MODALIAS
string in the uevent file for the device.  However, the device core does
not automatically provide this, and needs each bus_type to implement a
uevent method to generate these strings.  The MDIO bus does not provide
such a method, so no MODALIAS string is provided:

.# cat /sys/bus/mdio_bus/devices/f1072004.mdio-mii\:04/uevent
DRIVER=mv88e6085
OF_NAME=switch
OF_FULLNAME=/soc/internal-regs/mdio@72004/switch@4
OF_COMPATIBLE_0=marvell,mv88e6085
OF_COMPATIBLE_N=1

In the case of OF-based devices, the solution is easy -
of_device_uevent_modalias() does the work for us.  After this is done,
the uevent file looks like this:

.# cat /sys/bus/mdio_bus/devices/f1072004.mdio-mii\:04/uevent
DRIVER=mv88e6085
OF_NAME=switch
OF_FULLNAME=/soc/internal-regs/mdio@72004/switch@4
OF_COMPATIBLE_0=marvell,mv88e6085
OF_COMPATIBLE_N=1
MODALIAS=of:NswitchT<NULL>Cmarvell,mv88e6085

which results in auto-loading of the Marvell DSA driver on Clearfog
platforms.

Fixes: c0405563 ("ARM: dts: armada-388-clearfog: Utilize new DSA binding")
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Marvell driver incorrectly provides phydev->lp_advertising as the
logical and of the link partner's advert and our advert.  This is
incorrect - this field is supposed to store the link parter's unmodified
advertisment.

This allows ethtool to report the correct link partner auto-negotiation
status.

Fixes: be937f1f ("Marvell PHY m88e1111 driver fix")
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Building the driver with CONFIG_SMP disabled results in a harmless
warning:

ethernet/mellanox/mlx5/core/main.c: In function 'mlx5_irq_set_affinity_hint':
ethernet/mellanox/mlx5/core/main.c:615:6: error: unused variable 'irq' [-Werror=unused-variable]

It's better to express the conditional compilation using IS_ENABLED()
here, as that lets the compiler see what the intented use for the variable
is, and that it can be silently discarded.

Fixes: b665d98e ("net/mlx5: Tolerate irq_set_affinity_hint() failures")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

'static' was not enough, the helpers must be 'static inline'

net/dsa/mv88e6xxx/global2.h:123:12: error: 'mv88e6xxx_g2_misc_4_bit_port' defined but not used [-Werror=unused-function]
net/dsa/mv88e6xxx/global2.h:117:12: error: 'mv88e6xxx_g2_pvt_write' defined but not used [-Werror=unused-function]

Fixes: c21fbe29 ("net: dsa: mv88e6xxx: Add missing static to stub functions")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current implementation lacks the logic for providing management
firmware with RDMA-related statistics; [much] worse than that -
it logs such events by default to system logs.

Since the statistics' gathering is done periodically, using sufficiently
new management firmware the system logs would get filled with these
unnecessary prints.

For now, reduce the verbosity of the log so that it would not be
logged by default.

Fixes: 6c754246 ("qed: Add support for NCSI statistics")
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During PCI error recovery process, specifically on eeh_err_detected()
we might have a NULL netdev struct, hence a direct dereference will
lead to a kernel oops. This was observed with latest upstream kernel
(v4.12-rc2) on Chelsio adapter T422-CR in PowerPC machines.

This patch checks for NULL pointer and avoids the crash, both in
eeh_err_detected() and eeh_resume(). Also, we avoid to trigger
a fatal error or to try disabling interrupts on FW during PCI
error recovery, because: (a) driver might not be able to accurately
access PCI regions in this case, and (b) trigger a fatal error
_during_ the recovery steps is a mistake that could prevent the
recovery path to complete successfully.
Reported-by: NHarsha Thyagaraja <hathyaga@in.ibm.com>
Signed-off-by: NGuilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>