The byte count table is only used for aggregation. Updating it
in other cases caused fragmented frames to be dropped.

This fixes http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=2004Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add new lock to be used when accessing some registers. Also move
    the register lock and iwl_grab_nic_access inside the function for register access. This
    will prevent from forgetting to hold locks and nic access in the right way and make code
    easier to maintain.

    We over use the priv->lock spin lock and I guess we need to add new
    one for Tx queue after that we might need to change most of these lock to
    BH and just keep priv->lock as irq type.
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch clean up the code for NL80211_IFTYPE_MONITOR mode,
priv->iw_mode is set in add_interface, but add_interface is never called
for monitor mode.
The only way mac80211 informs us about monitor mode is through
configuring filter; since iw_mode will never set to
NL80211_IFTYPE_MONITOR, modify and remove all the code refer to
NL80211_IFTYPE_MONITOR and replace with iwl_is_monitor_mode() function
call.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adding few more debug messages if encounter error when driver
try to start tx aggregation queue. Also change from IWL_ERR to
IWL_DEBUG_HT is the HW legacy queue is empty when driver request to move
to aggregation queue.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A few issues wrt DMA were uncovered when using the driver with swiotlb.
- driver should not use memory after it has been mapped
- iwl3945's RX queue management cannot use all of iwlagn because
  the size of the RX buffer is different. Revert back to using
  iwl3945 specific routines that map/unmap memory.
- no need to "dma_syn_single_range_for_cpu" followed by pci_unmap_single,
  we can just call pci_unmap_single initially
- only map the memory area that will be used by device. this is especially
  relevant to the mapping of iwl_cmd. we should not map the entire
  structure because the meta data at the beginning of structure contains
  the address to be used later for unmapping. If the address to be used for
  unmapping is stored in mapped data it creates a problem.
- ensure that _if_ memory needs to be modified after it is mapped that we
  call _sync_single_for_cpu first, and then release it back to device with
  _sync_single_for_device
- we mapped the wrong length of data for host commands, with mapped length
  differing with length provided to device, fix that.

Thanks to Jason Andryuk <jandryuk@gmail.com> for significant bisecting
help to find these issues.

This fixes http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1964Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Tested-by: NJason Andryuk <jandryuk@gmail.com>
Tested-by: NBen Gamari <bgamari@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When debugging TX issues it is helpful to know the seq nr of the
frame being transmitted. The seq nr is printed as part of ucode's
log informing us which frame is being processed. Having this information
printed in driver log makes it easy to match activities between driver
and firmware.

Also make possible to print TX flags directly. These are already printed
as part of entire TX command, but having it printed directly in cpu format
makes it easier to look at.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes all the virtual A-MPDU-queue bookkeeping from
mac80211. Curiously, iwlwifi already does its own bookkeeping, so
it doesn't require much changes except where it needs to handle
starting and stopping the queues in mac80211.

To handle the queue stop/wake properly, we rewrite the software
queue number for aggregation frames and internally to iwlwifi keep
track of the queues that map into the same AC queue, and only talk
to mac80211 about the AC queue. The implementation requires calling
two new functions, iwl_stop_queue and iwl_wake_queue instead of the
mac80211 counterparts.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: Reinette Chattre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fix related to bug 1921 at
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1921

when detect error during stopping tx aggregation queue, report the error to
help identify the problem.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl_cmd_queue_free needs to be used to free up the cmd_queue,
as TFD slots for cmd_queue and tx_queue are different.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When iwlwifi runs on IOMMU, IOMMU generates a lot of PTE write faults
because PTE write bit is not set on some of PTE's. This is because iwlwifi
driver calls DMA mapping with PCI_DMA_TODEVICE which is read only in mapping
PTE. But iwlwifi device actually writes to the mapped page to update its contents.
This issue is not exposed in swiotlb. But VT-d hardware can capture this fault and
stop the fault transaction.

The iwl TX command contains a scratch field that is updated by uCode to
indicate retry counts. For 5000 series the patch is required also for
regular frames, but this patch does not differenciate.
Signed-off-by: NFenghua Yu <fenghua.yu@intel.com>
Acked-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When iwlan runs on IOMMU, IOMMU generates a lot of PTE write faults
because PTE write bit is not set on some of PTE's.  This is because
iwlan driver calls DMA mapping with PCI_DMA_TODEVICE which is read only
in mapping PTE.  But iwlan device actually writes to the mapped page to
update its contents.  This issue is not exposed in swiotlb.  But VT-d
hardware can capture this fault and stop the fault transaction.

The following patch fixes the issue.
Signed-off-by: NFenghua Yu <fenghua.yu@intel.com>
Reviewed-by: NBhavesh Davda <bhavesh@vmware.com>
Tested-by: NChris Wright <chrisw@sous-sol.org>
Acked-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The base versions handle constant folding now.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Call IWL_DEBUG macro with explicit priv argument.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Acked-by: NSamuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fix compilation warning in printk formatting
iwl_tx_queue_alloc function.
Cleanup the code a bit on the way.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

By adding an additional hw_params (tfd_size) and a new iwl_lib ops (txq_init),
we can now use the iwlcore TX queue management routines.
We had to add a new hw_params because we need to allocate the right DMA buffer
for TFDs, and those have a different sizes depending if you're on 3945 or agn.
Signed-off-by: NSamuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of having both tfds and tfds39, we can just have a void *tfds.
It makes the tx_queue structure nicer, and the code cleaner. It also helps
with further TX queues management code merging.
Signed-off-by: NSamuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With the previously added tfd related ops, we can now use the iwl-tx.c host
command enqueue routine. Since the 3945 host command specific
routines are identical to the agn ones, we can just remove them from the 3945
code.
Signed-off-by: NSamuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The TFD structures for 3945 and agn HWs are fundamentally different. We thus
need to define operations for attaching and freeing them. This will allow us
to share a fair amount of code (cmd and tx queue related) between both
drivers.
Signed-off-by: NSamuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

IWL_ERR doesn't use hidden priv pointer.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

IWL_WARN doesn't use hidden priv pointer.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use IWL_ macros where possible to unify debug output usage.
Define new unconditional printouts IWL_ERR, IWL_WARN, IWL_INFO,
and IWL_CRIT which don't use hidden priv pointer.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes unused parameter and unused local variable in
methods in iwl-tx.c:

- Remove a parameter (is_unicast) from iwl_tx_cmd_build_basic().

- Remove an unused variable name unicast from iwl_tx_skb().
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch replaces personal emails with hopefully
always valid Intel Linux Wireless, which will be routed
to a current maintainer
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch fixes the misuse of microsecond with millisecond in the
polling mechanism of the iwlwifi driver. The impact of this problem
is the unacceptable latency for the whole system (especially during
bringing down the wlan interface).
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Acked-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch fixes the misuse of DMA channel number by Tx queue number in
iwl_tx_ctx_stop().

The problem was originally reported by Wu Fengguang who complains
iwlagn driver takes too long time when issuing `ifconfig wlan0 down`.
The patch now decreases the interface bring down time from 2 seconds
to 0.8 second.

This fixes bugs:
http://bugzilla.kernel.org/show_bug.cgi?id=11956
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1790Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Tested-by: NFengguang Wu <fengguang.wu@intel.com>
Acked-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch configures correctly TX DMA channel. It is not
the same as TX queue.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Acked-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch cleans up some flow handler related document. It also
removes some blank lines.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Acked-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Patch fixes checkpatch.pl errors for iwlwifi.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds additional info about wrong command queue bug
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This moves byte count tables to tx domain removing completely
ambivalent shared data. Changes handling of allocation
byte count tables and keep warm consistent memory
Moves general tx scheduler definitions from iwl-4956-hw.h
to iwl-fh.h
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch cleans up FH bits and adds missing register values
that will be used later in TX initialization rewrite
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch utilize 5000 new TX response command
which contains all necessary information and avoids
back referencing to the original TX frame.
It also change handling of software queue tracking
4965 flow is aligned with changes as much as possible.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Reviewed-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch makes clear that tx command is attached to the same tfd as
the tx packet
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch:
1. fixes command DMA unmapping, this might be visible only
	on platforms where DMA unmapping is no noop such as PPC64 (not tested)
2. attaches correctly high memory part of the host command buffer
3. changes structure of TFD TB
	instead of describing transmit buffer (TB) tuple it describes single
	TB and makes code more readable on price of one unaligned access
4. eliminates using of IWL_GET/SET_BITs for TFD handling
5. renames TFD structures to mach the HW spec
6. reduces iwl_tx_info size by reserving first TB to the host command

This patch should not have any visible effect on x86 32

This patch is rework of
iwlwifi: fix DMA code and bugs from
Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

TX antenna toggling is requested for management frames in tx and
scanning. I addition toggling in scanning was incorrect;
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Reviewed-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds iwl_cmd_queue_free function and
separate cmd queue freeing from regular tx queue freeing.
This improves readability and adds one more step in
restructuring  of cmd queue handling
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Reviewed-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.

I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This BUG_ON really shouldn't trigger, but if it does, as on my machine,
it leaves you wondering what happened because you won't see it. Let's
instead leak a bit of state and memory and at least make it possible to
report it to the kerneloops project to track it.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>