Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 17 1月, 2014 9 次提交
  3. 16 1月, 2014 1 次提交
  5. 15 1月, 2014 6 次提交
  7. 09 1月, 2014 7 次提交
  9. 01 1月, 2014 1 次提交
  11. 28 12月, 2013 5 次提交
  13. 22 12月, 2013 11 次提交
    • C
      KVM: arm-vgic: Support CPU interface reg access · fa20f5ae
      由 Christoffer Dall 提交于 
      Implement support for the CPU interface register access driven by MMIO
address offsets from the CPU interface base address.  Useful for user
space to support save/restore of the VGIC state.

This commit adds support only for the same logic as the current VGIC
support, and no more.  For example, the active priority registers are
handled as RAZ/WI, just like setting priorities on the emulated
distributor.
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      fa20f5ae
    • C
      KVM: arm-vgic: Add GICD_SPENDSGIR and GICD_CPENDSGIR handlers · 90a5355e
      由 Christoffer Dall 提交于 
      Handle MMIO accesses to the two registers which should support both the
case where the VMs want to read/write either of these registers and the
case where user space reads/writes these registers to do save/restore of
the VGIC state.

Note that the added complexity compared to simple set/clear enable
registers stems from the bookkeping of source cpu ids.  It may be
possible to change the underlying data structure to simplify the
complexity, but since this is not in the critical path at all, this will
do.

Also note that reading this register from a live guest will not be
accurate compared to on hardware, because some state may be living on
the CPU LRs and the only way to give a consistent read would be to force
stop all the VCPUs and request them to unqueu the LR state onto the
distributor.  Until we have an actual user of live reading this
register, we can live with the difference.
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      90a5355e
    • C
      KVM: arm-vgic: Support unqueueing of LRs to the dist · cbd333a4
      由 Christoffer Dall 提交于 
      To properly access the VGIC state from user space it is very unpractical
to have to loop through all the LRs in all register access functions.
Instead, support moving all pending state from LRs to the distributor,
but leave active state LRs alone.

Note that to accurately present the active and pending state to VCPUs
reading these distributor registers from a live VM, we would have to
stop all other VPUs than the calling VCPU and ask each CPU to unqueue
their LR state onto the distributor and add fields to track active state
on the distributor side as well.  We don't have any users of such
functionality yet and there are other inaccuracies of the GIC emulation,
so don't provide accurate synchronized access to this state just yet.
However, when the time comes, having this function should help.
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      cbd333a4
    • C
      KVM: arm-vgic: Add vgic reg access from dev attr · c07a0191
      由 Christoffer Dall 提交于 
      Add infrastructure to handle distributor and cpu interface register
accesses through the KVM_{GET/SET}_DEVICE_ATTR interface by adding the
KVM_DEV_ARM_VGIC_GRP_DIST_REGS and KVM_DEV_ARM_VGIC_GRP_CPU_REGS groups
and defining the semantics of the attr field to be the MMIO offset as
specified in the GICv2 specs.

Missing register accesses or other changes in individual register access
functions to support save/restore of the VGIC state is added in
subsequent patches.
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      c07a0191
    • C
      arm/arm64: kvm: Set vcpu->cpu to -1 on vcpu_put · e9b152cb
      由 Christoffer Dall 提交于 
      The arch-generic KVM code expects the cpu field of a vcpu to be -1 if
the vcpu is no longer assigned to a cpu.  This is used for the optimized
make_all_cpus_request path and will be used by the vgic code to check
that no vcpus are running.
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      e9b152cb
    • C
      KVM: arm-vgic: Make vgic mmio functions more generic · 1006e8cb
      由 Christoffer Dall 提交于 
      Rename the vgic_ranges array to vgic_dist_ranges to be more specific and
to prepare for handling CPU interface register access as well (for
save/restore of VGIC state).

Pass offset from distributor or interface MMIO base to
find_matching_range function instead of the physical address of the
access in the VM memory map.  This allows other callers unaware of the
VM specifics, but with generic VGIC knowledge to reuse the function.
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      1006e8cb
    • C
      irqchip: arm-gic: Define additional MMIO offsets and masks · 0307e177
      由 Christoffer Dall 提交于 
      Define CPU interface offsets for the GICC_ABPR, GICC_APR, and GICC_IIDR
registers.  Define distributor registers for the GICD_SPENDSGIR and the
GICD_CPENDSGIR.  KVM/ARM needs to know about these definitions to fully
support save/restore of the VGIC.

Also define some masks and shifts for the various GICH_VMCR fields.

Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      0307e177
    • C
      KVM: arm-vgic: Set base addr through device API · ce01e4e8
      由 Christoffer Dall 提交于 
      Support setting the distributor and cpu interface base addresses in the
VM physical address space through the KVM_{SET,GET}_DEVICE_ATTR API
in addition to the ARM specific API.

This has the added benefit of being able to share more code in user
space and do things in a uniform manner.

Also deprecate the older API at the same time, but backwards
compatibility will be maintained.
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      ce01e4e8
    • C
      KVM: arm-vgic: Support KVM_CREATE_DEVICE for VGIC · 7330672b
      由 Christoffer Dall 提交于 
      Support creating the ARM VGIC device through the KVM_CREATE_DEVICE
ioctl, which can then later be leveraged to use the
KVM_{GET/SET}_DEVICE_ATTR, which is useful both for setting addresses in
a more generic API than the ARM-specific one and is useful for
save/restore of VGIC state.

Adds KVM_CAP_DEVICE_CTRL to ARM capabilities.

Note that we change the check for creating a VGIC from bailing out if
any VCPUs were created, to bailing out if any VCPUs were ever run.  This
is an important distinction that shouldn't break anything, but allows
creating the VGIC after the VCPUs have been created.
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      7330672b
    • C
      ARM: KVM: Allow creating the VGIC after VCPUs · e1ba0207
      由 Christoffer Dall 提交于 
      Rework the VGIC initialization slightly to allow initialization of the
vgic cpu-specific state even if the irqchip (the VGIC) hasn't been
created by user space yet.  This is safe, because the vgic data
structures are already allocated when the CPU is allocated if VGIC
support is compiled into the kernel.  Further, the init process does not
depend on any other information and the sacrifice is a slight
performance degradation for creating VMs in the no-VGIC case.

The reason is that the new device control API doesn't mandate creating
the VGIC before creating the VCPU and it is unreasonable to require user
space to create the VGIC before creating the VCPUs.

At the same time move the irqchip_in_kernel check out of
kvm_vcpu_first_run_init and into the init function to make the per-vcpu
and global init functions symmetric and add comments on the exported
functions making it a bit easier to understand the init flow by only
looking at vgic.c.
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      e1ba0207
    • A
      ARM/KVM: save and restore generic timer registers · 39735a3a
      由 Andre Przywara 提交于 
      For migration to work we need to save (and later restore) the state of
each core's virtual generic timer.
Since this is per VCPU, we can use the [gs]et_one_reg ioctl and export
the three needed registers (control, counter, compare value).
Though they live in cp15 space, we don't use the existing list, since
they need special accessor functions and the arch timer is optional.
Acked-by: NMarc Zynger <marc.zyngier@arm.com>
Signed-off-by: NAndre Przywara <andre.przywara@linaro.org>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
      39735a3a