Replace kmalloc+memset with kzalloc
Signed-off-by: NYan Burman <yan_952@hotmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use canonical defines for the Apple USB device IDs.
Also add the Geyser IV devices missing in my previous patch.
Signed-off-by: NJulien BLACHE <jb@jblache.org>
Acked-by: NDmitry Torokhov <dtor@insightbb.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Just digging through code and found these needless variable initializations. So here is the patch.
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

usb_device_match() can now become static.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove minor double-declaration goof.
Signed-off-by: NMilan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Make the pxa2xx_udc driver recognize a newer revision of the IXP425 chip.
Signed-off-by: NMilan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Adds support for the DMC TSC-10 and TSC-25 usb touchscreen controllers.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NDaniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch contains the following possible cleanups:
- make the needlessly global ftdi_release_platform_dev() static
- remove the unused usb_ftdi_elan_read_reg()
- proper prototypes for the following functions:
  - usb_ftdi_elan_read_pcimem()
  - usb_ftdi_elan_write_pcimem()

Note that the misplaced prototypes for the latter ones in
drivers/usb/host/u132-hcd.c were buggy. Depending on the calling
convention of the architecture calling one of them could have turned
your stack into garbage.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch makes the needlessly global "u132_hcd_wait" static.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If at some point cypress_init() fails deregister
only the resources that were registered until that point.
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Certain boards seem to like to issue false overcurrent notifications, for
example on ports that don't have anything connected to them.  This looks
like a hardware error, at the level of noise to those ports' overcurrent
input signals (or non-debounced VBUS comparators).  This surfaces to users
as truly massive amounts of syslog spam from khubd (which is appropriate
for real hardware problems, except for the volume from multiple ports).

Using this new "ignore_oc" flag helps such systems work more sanely, by
preventing such indications from getting to khubd (and spam syslog).  The
downside is of course that true overcurrent errors will be masked; they'll
appear as spontaneous disconnects, without the diagnostics that will let
users troubleshoot issues like short circuited cables.

Note that the bulk of these reports seem to be with VIA southbridges, but
I think some were with Intel ones.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

EHCI hooks for high speed electrical tests of the root hub ports.

The expectation is that a usermode program actually triggers the test,
making the same control request it would make for an external hub.
Tests for peripheral upstream ports would issue a different request.
In all cases, the hardware needs re-initialization before it could
be used "normally" again (e.g. unplug/replug, rmmod/modprobe).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The net2280 driver is too eager to send zero-length packets when
IN tokens are received on ep0.  No such packet should be sent (the
driver should NAK) before the gadget driver has queued the proper
response.  Otherwise deferred responses are impossible.

This patch (as823) makes net2280 avoid sending ZLPs for IN transfers
on ep0 until a response has been submitted, and avoids stalling when an
OUT packet is received before a request has been submitted for an OUT
transfer on ep0.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Possible memleak fix on error path. The changes:

- out_kfree2 and out_free_urb replaced
- missing scsi_host_put() added

Here it goes:
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NOliver Neukum <oliver@neukum.name>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The mass storage device from Digitech designed for Flash Cards, as found
on (for example) the GNX4 device has issues with residue, similar to the
bug report at http://kerneltrap.org/node/6297.  This patch adds the
faulty storage device to unusual_devs.h, this not only reduces the noise
in dmesg but also increases the transfer speeds by a factor of 7x for me
(89kB/s -> 637kB/s).

T:  Bus=02 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#=  4 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1210 ProdID=0003 Rev= 1.00
S:  Manufacturer=DigiTech HMG
S:  Product=DigiTech Mass Storage
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50
Driver=usb-storage
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
Signed-off-by: NJaco Kroon <jaco@kroon.co.za>
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as821) fixes a compiler warning when CONFIG_PM isn't on
("usb_autosuspend_work" defined but not used).
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

> 2006/11/11, Adrian Bunk <bunk@stusta.de>:
> > The Coverity checker spotted the following in
> > drivers/usb/serial/aircable.c:
> >
> > <--  snip  -->
> >
> > ...
> > static void aircable_read(void *params)
> > {
> > ...


Hi everyone,
Sorry for the long time response but here is the patch, I think this way should
work, if anyone has any suggestion let me know. What I do now is, in case I
don't have the tty available I reschedule the work, I have tried it and it
works with no problem, I even tried removing the device, and didn't find
anything strange.
Signed-off-by: NNaranjo Manuel <naranjo.manuel@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

All the other root-hub suspend or resume log messages, in ohci-hcd or
any of the other host controller drivers, use the debug priority
level.  This patch (as815) makes the one single exception behave like
all the rest.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_free_urb() cleanup
- usb_kill_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_kill_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_kill_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_free_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_kill_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_free_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_kill_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_free_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_kill_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_free_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_kill_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_free_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_free_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Hello,

- usb_free_urb() cleanup
- usb_kill_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_free_urb() cleanup
- usb_kill_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_free_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_free_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Hello,

- usb_free_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_free_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_free_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_free_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- usb_free_urb() cleanup
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>