Allow device drivers to enqueue URBs to control endpoints on devices under
an xHCI host controller.  Each control transfer is represented by a
series of Transfer Descriptors (TDs) written to an endpoint ring.  There
is one TD for the Setup phase, (optionally) one TD for the Data phase, and
one TD for the Status phase.

Enqueue these TDs onto the endpoint ring that represents the control
endpoint.  The host controller hardware will return an event on the event
ring that points to the (DMA) address of one of the TDs on the endpoint
ring.  If the transfer was successful, the transfer event TRB will have a
completion code of success, and it will point to the Status phase TD.
Anything else is considered an error.

This should work for control endpoints besides the default endpoint, but
that hasn't been tested.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

xHCI needs to get a "Slot ID" from the host controller and allocate other
data structures for every USB device.  Make usb_alloc_dev() and
usb_release_dev() allocate and free these device structures.  After
setting up the xHC device structures, usb_alloc_dev() must wait for the
hardware to respond to an Enable Slot command.  usb_alloc_dev() fires off
a Disable Slot command and does not wait for it to complete.

When the USB core wants to choose an address for the device, the xHCI
driver must issue a Set Address command and wait for an event for that
command.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add functionality for getting port status and hub descriptor for xHCI root
hubs.  This is WIP because the USB 3.0 hub descriptor is different from
the USB 2.0 hub descriptor.  For now, we lie about the root hub descriptor
because the changes won't effect how the core talks to the root hub.
Later we will need to add the USB 3.0 hub descriptor for real hubs, and
this code might change.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

xHCI host controllers can optionally implement a no-op test.  This
simple test ensures the OS has correctly setup all basic data structures
and can correctly respond to interrupts from the host controller
hardware.

There are two rings exercised by the no-op test:  the command ring, and
the event ring.

The host controller driver writes a no-op command TRB to the command
ring, and rings the doorbell for the command ring (the first entry in
the doorbell array).  The hardware receives this event, places a command
completion event on the event ring, and fires an interrupt.

The host controller driver sees the interrupt, and checks the event ring
for TRBs it can process, and sees the command completion event.  (See
the rules in xhci-ring.c for who "owns" a TRB.  This is a simplified set
of rules, and may not contain all the details that are in the xHCI 0.95
spec.)

A timer fires every 60 seconds to debug the state of the hardware and
command and event rings.  This timer only runs if
CONFIG_USB_XHCI_HCD_DEBUGGING is 'y'.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add PCI initialization code to take control of the xHCI host controller
away from the BIOS, halt, and reset the host controller.  The xHCI spec
says that BIOSes must give up the host controller within 5 seconds.

Add some host controller glue functions to handle hardware initialization
and memory allocation for the host controller.  The current xHCI
prototypes use PCI interrupts, but the xHCI spec requires MSI-X
interrupts.  Add code to support MSI-X interrupts, but use the PCI
interrupts for now.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>