Do not set max_id value received from FW. Once SAS transport layer is
introduced max_id value is missleading to SCSI mid layer. Use max_id to
infinite value.

logic of can queue of scsi host is changed.
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Change config request timeout value to 30 seconds.
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Handle insufficient resources status as similar to busy status.
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Removed mptscsih_timer_expired. This timer is no more use.
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Change DEFINED value of can queue for FC and SAS devices.
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Reported-by: NRice Brown <rick.brown@oit.gatech.edu>
Signed-Off-by: NChandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Universally, SCSI functions assume the lengths fed in are those of the buffer
to DMA data to, not the lengths of the data minus the header.
scsi_vpd_inquiry() assumed the latter and got it wrong, so fix up all the
functions to use the correct assumption (and fix a bug where INQUIRY in SCSI-2
dcannot go over 255).


[jejb: Matthew posted an identical version of this at the same time I did]
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

An IBM tape drive failed to complete a PERSISTENT RESERVE IN within the scsi
cmd timeout.  Error recovery was initiated and it sequenced from abort through
taking the tape drive offline.

The device was taken offline because it repeatedly responded to the TUR command
issued by error recovery with a RESERVATION CONFLICT status.  The tape drive
was reserved to another system.  This is perfectly legitimate response to TUR,
and is one that an escalation of recovery is unlikely to clear.  Further,
escalation of recovery can have undesirable side effects on the operation of
tape drives shared with other initiators.

Instead of escalating recovery, error recovery should treat the RESERVATION
CONFLICT response to the TUR as a good status, giving the issuer of the
command the opportunity to handle the timeout and reservation conflict.
Signed-off-by: NMichael reed <mdr@sgi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

In nsp_cs_config there is a wrong struct nsp_cs_configdata allocation.
It allocates only sizeof(pointer to nsp_cs_configdata) for a whole
structure. Add a dereference to the sizeof to allocate
sizeof(nsp_cs_configdata).
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Verify that ch->dt is not NULL before using it.
Signed-off-by: NDavidlohr Bueso <dave@gnu.org>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The allocated struct is manually zeroed after allocation, so avoid using
the (broken) kzalloc mempool (which does not re-zero previously used items
when they are returned to the pool).
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NSage Weil <sage@newdream.net>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

When the multiqueue mode fails to work, the driver falls back on single
queue mode. This ensures that the firmware is reinitialized with single
queue options and all the resources are readjusted accordingly.
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The interrupt handler clears the interrupt status register for response
updates in the base queue while working in the multique mode. This could lead
to missing interrupt for async events, mail box completions etc. as these are
also handled in the base queue.  The fix ensures that the interrupt bit is not
cleared for response updates in the ISR when the driver is working in
multiqueue mode.
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

One byte added to make the IOCB structure satisfy
size requirements.
Signed-off-by: NShyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NSantosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

If vports are created and topology is changed to Loop only, the
driver continuously gets a LIP reset occurred and keeps trying to
enable the vport.  Only manage requests during F_Port.
Signed-off-by: NLalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NSantosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The RSCN processing is skipped if the event received is global and vha is not recipient.
Signed-off-by: NSantosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Treat a global port-unavailable PORT_UPDATE (8014h) AEN as a
loop-down event.  For this case, within the FCoE domain, the
'logical' interface has been terminated, but the driver will
not receive the classic LOOP_DOWN AEN.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NRavi Anand <ravi.anand@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Use scsi_dh_set_params() set parameters provided. Save the parameters in
parse_hw_handler() and use it in parse_path().
Reported-by: NEddie Williams <Eddie.Williams@steeleye.com>
Signed-off-by: NChandra Seetharaman <sekharan@us.ibm.com>
Tested-by: NEddie Williams <Eddie.Williams@steeleye.com>
Cc: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Handle the parameters provided by user thru multipath.

This handler expects only 2 parameters and their value can either be 0 or 1.

This code originates from the old dm-emc.c file. Appropriate changes have
been made to make it work in the new design.
Reported-by: NEddie Williams <Eddie.Williams@steeleye.com>
Signed-off-by: NChandra Seetharaman <sekharan@us.ibm.com>
Tested-by: NEddie Williams <Eddie.Williams@steeleye.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

When we moved the device handler functionality from dm layer to SCSI layer
we dropped the parameter functionality.

This path adds an interface to scsi dh layer to set device handler
parameters.

Basically, multipath layer need to create a string with all the parameters
and call scsi_dh_set_params() after it called scsi_dh_attach() on a
device.

If a device handler provides such an interface it will handle the parameters
as it expects them.
Reported-by: NEddie Williams <Eddie.Williams@steeleye.com>
Signed-off-by: NChandra Seetharaman <sekharan@us.ibm.com>
Tested-by: NEddie Williams <Eddie.Williams@steeleye.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Now that hot add works correctly, if a new device is added, we're still
operating on stale enclosure data, so fix that by updating the enclosure
diagnostic pages when we get notified of a device hot add
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Right at the moment, hot removal of a device within an enclosure does
nothing (because the intf_remove only copes with enclosure removal not
with component removal). Fix this by adding a function to remove the
component.  Also needed to fix the prototype of
enclosure_remove_device, since we know the device we've removed but
not the internal component number
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

In a situation either with expanders or with multiple enclosure
devices, hot add doesn't always work.  This is because we try to find
a single enclosure device attached to the host.  Fix this by looping
over all enclosure devices attached to the host and also by making the
find loop recognise that the enclosure devices may be expander remote
(i.e. not parented by the host).
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

ipr_cmd_label[] isn't big enough for an eight byte string plus terminator.
Fix by shortening the string to seven bytes.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

When bnx2i_adapter_ready() fails, connection handle(cid) = 0 is wrongly freed
because 'cid' is not yet allocated for the endpoint.  Fix is to initialize
bnx2i_ep->ep_iscsi_cid to '-1' in bnx2i_alloc_ep() and not in
bnx2i_ep_connect() to avoid releasing invalid 'cid'.  There is already a check
in bnx2i_free_iscsi_cid() not to free invalid iscsi connection handle (-1)
Signed-off-by: NAnil Veerabhadrappa <anilgv@broadcom.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Without the fix bnx2i would fail tt->xmit_task() when link is down and
libiscsi would have already incremented session->cmdsn before calling bnx2i's
xmit_task() entry point and will just return the command to SCSI-ML when
xmit_task() fails. libiscsi does not retract the session->cmdsn as the command
was never sent on wire.  It is generally good idea for LLD, bnx2i to accept
the scsi cmnd/nopout and let upper layer timeout and go though normal session
recovery process.  When link is down, unsolicited nopout will not be accepted
by bnx2i and connection will never enter recovery state. This fix is required
for MPIO to work corectly
Signed-off-by: NAnil Veerabhadrappa <anilgv@broadcom.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The phys_dev was used only to locate common offload EM instance for all
FCoE instances on a eth devices in function fcoe_em_config, so just updated
fcoe_em_config to look for actual real eth device in locating common offload
EM instance and then no need to store phys_dev in fcoe_softc, so removes
phys_dev from fcoe_softc also.

Renames fcoe_softc real_dev to netdev and updates all its uses to use netdev.

So effectively no functional change, use of single netdev instead phys_dev
and real_dev saves one pointer memory in fcoe_softc, also real_dev used here
was confusing with vlan driver terminology since real_dev in vlan driver is
referred to physical eth device.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

I don't believe this check is needed any more in the current kernel, which,
if I understand correctly, is for compound page where only the first page
is supposed to get ref-counted.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

FC_FRAME_SG_LEN is 4 which is too small when offload is enabled. Actually, the
WARN_ON() in fc_fcp_send_data() should be:

	WARN_ON(skb_shinfo(fp_skb(fp))->nr_frags > MAX_SKB_FRAGS);

But since we will not get anything more than 64K anyway, so there is no need
to do this anyway here. Therefore, I am getting rid of FC_FRAME_SG_LEN here
and the WARN_ON here.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Remove the extra ifdef for NETIF_F_FSO and NETIF_F_FCOE_CRC since they are
already defined in the current kernel as in include/linux/netdevice.h.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Updates fcoe_em_config to allocate a single instance of sharable offload
EM for supported lp->lro_xid per eth device, and then share this EM
for subsequently more lports creation on same eth device (e.g when using
VLAN).

Adds tiny fcoe_oem_match function for offload EM to return true for read
types IO to have read IO exchanges allocated from offload shared EM.

Removes fc_em_alloc_xid function completely which was needed to manage
two xid ranges within a EM, this is not needed any more with allocation
of separate sharable offload EM per eth device. Instead this patch adds
simple xid allocation logic to manage single xid range.

Adds fc_exch_em_alloc with mp->next_xid as cursor to allocate new xid
from single xid range of EM, uses mp->next_xid instead removed mp->last_xid
which slightly increase probability of finding empty xid on exch allocation.

Removes restriction of not allowing use of xid zero along with changing
two xid range change to single xid range.

Makes fc_fcp_ddp_setup calling conditional to only xid allocated from
shared offload EM.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Modifies fcoe_hostlist_lock uses such that a new EM allocation in
fcoe_em_config and adding new fcoe_softc using fcoe_hostlist_add
are atomic, this is to ensure that a shared offload EM gets allocated
only once per eth device for its all lports.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Modifies current code to use EM anchor list in EM allocation, EM free,
EM reset, exch allocation and exch lookup code paths.

 1. Modifies fc_exch_mgr_alloc to accept EM match function and then
    have allocated EM added to the lport using fc_exch_mgr_add API
    while also updating EM kref for newly added EM.

 2. Updates fc_exch_mgr_free API to accept only lport pointer instead
    EM and then have this API free all EMs of the lport from EM anchor
    list.

 3. Removes single lport pointer link from the EM, which was used in
    associating lport pointer in newly allocated exchange. Instead have
    lport pointer passed along new exchange allocation call path and
    then store passed lport pointer in newly allocated exchange, this
    will allow a single EM instance to be used across more than one
    lport and used in EM reset to reset only lport specific exchanges.

 4. Modifies fc_exch_mgr_reset to reset all EMs from the EM anchor list
    of the lport, adds additional exch lport pointer (ep->lp) check for
    shared EM case to reset exchange specific to a lport requested reset.

 5. Updates exch allocation API fc_exch_alloc to use EM anchor list and
    its anchor match func pointer. The fc_exch_alloc will walk the list
    of EMs until it finds a match, a match will be either null match
    func pointer or call to match function returning true value.

 6. Updates fc_exch_recv to accept incoming frame on local port using
    only lport pointer and frame pointer without specifying EM instance
    of incoming frame. Instead modified fc_exch_recv to locate EM for the
    incoming frame by matching xid of incoming frame against a EM xid range.
    This change was required to use EM list in libfc Rx path and after this
    change the lport fc_exch_mgr pointer emp is not needed anymore, so
    removed emp pointer.

 7. Updates fnic for removed lport emp pointer and above modified libfc APIs
    fc_exch_recv, fc_exch_mgr_alloc and fc_exch_mgr_free.

 8. Removes exch_get and exch_put from libfc_function_template as these
    are no longer needed with EM anchor list and its match function use.
    Also removes its default function fc_exch_get.

A defect this patch introduced regarding the libfc initialization order in
the fnic driver was fixed by Joe Eykholt <jeykholt@cisco.com>.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Currently there is a 1:1 relationship between the lport
and exchange manager. This macro takes an EM as an argument
and determines the lport from it. However, later patches
will use an EM list per lport, so we will no longer have
this 1:1 relationship- this macro must change.

The FC_EM_DBG macro is rarely used. There are four callers,
two can use FC_LPORT_DBG instead and two can be removed
since they're not necessary. This patch makes those changes
and removes the macro.
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>