- 26 11月, 2009 10 次提交
-
-
由 Sekhar Nori 提交于
Implement autodetection of RMII PHY by shifting the decision to use the RMII PHY to da850_evm_ui_expander_setup() from da850_evm_init() earlier. Without this patch, selecting RMII PHY in the UI expander menu will make the MII PHY unusable even though UI board is not connected. The actual configuration and registration of the EMAC device is delayed to device_initcall() so it happens after the UI card detection is complete. A side effect of this patch is the removal of a voilation of Documentation/SubmittingPatches section 2.2 in function da850_evm_init() Signed-off-by: NSekhar Nori <nsekhar@ti.com> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-
由 Sergei Shtylyov 提交于
There have accumulated quite a lot of them after the code reorganizations... In several cases I had to replace #include <linux/dma-mapping.h> which wasn't needed directly but happened to #include <linux/err.h> which was needed. Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-
由 Chaithrika U S 提交于
DA850/OMAP-L138 EVM has a RMII Ethernet PHY on the UI daughter card. The PHY is enabled by proper programming of the IO Expander (TCA6416) ports. Also for RMII PHY to work, the MDIO clock of MII PHY has to be disabled since both the PHYs have the same address. This is done via the GPIO2[6] pin. This patch adds support for RMII PHY. This patch also adds a menuconfig option to select one or no peripheral connected to expander. Currently, sub-options in this menu are RMII and no peripheral.This menuconfig option is similar to the one present for UI card on DA830/OMAP-L137 EVM. Signed-off-by: NChaithrika U S <chaithrika@ti.com> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-
由 Chaithrika U S 提交于
DA850/OMAP-L138 EVM can be connected to an UI card which has various peripherals on it.The UI card has TCA6416 expander which can be probed to check whether the UI card is connected or not. If the UI card is connected, setup NOR and NAND devices. This is done via the expander setup callback. Signed-off-by: NChaithrika U S <chaithrika@ti.com> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-
由 Sekhar Nori 提交于
This patch adds support for using the TPS65070 PMIC found on the DA850/OMAP-L138 EVM. It defines the power rail consumer mapping and registers the the I2C based PMIC as a board device. The power rail constraints are derived from the maxmimum and minimum recommended operating condition values of the respective consumers derived from section 5.2 of the OMAP-L138 datasheet. Signed-off-by: NSekhar Nori <nsekhar@ti.com> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-
由 Sekhar Nori 提交于
Signed-off-by: NSekhar Nori <nsekhar@ti.com> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-
由 Sudhakar Rajashekhara 提交于
On the latest DA850/OMAP-L138 EVM (Beta) the GPIO pin number of LCD panel power has changed. This patch takes care of this change. Software will support only Beta versions of DA850/OMAP-L138 EVM. In the process, add the missing entry for data pin 0 and remove the GPIO specific pins from da850_lcdcntl_pins structure. EVM specific muxing for LCD is being done in the board file now. Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-
由 Mark A. Greer 提交于
Add RTC support for the da830/omap-l137 and da850/omap-l138 SoC's by leveraging existing the rtc-omap driver. Signed-off-by: NMark A. Greer <mgreer@mvista.com> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-
由 Mark A. Greer 提交于
Add support for the Sharp LCD035Q3DG01 graphical LCD. This requires a minor interface change to da8xx_register_lcdc() so that the board code can pass in the platform_data which describes the lcd controller that's to be used. Signed-off-by: NMark A. Greer <mgreer@mvista.com> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-
由 Mark A. Greer 提交于
For consistency with existing code, change the name of da8xx_init_mcasp() to da8xx_register_mcasp(). Signed-off-by: NMark A. Greer <mgreer@mvista.com> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-
- 26 8月, 2009 9 次提交
-
-
由 Chaithrika U S 提交于
Tested on DM6446, DM355, DM6447, DA850 EVMs. Signed-off-by: NChaithrika U S <chaithrika@ti.com> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-
由 Sudhakar Rajashekhara 提交于
On DA850/OMAP-L138 EVM, MMC/SD and NOR Flash share some of the AEMIF pins. This patch prints out a warning during booting, if both MMC/SD and NOR Flash are enabled in kernel menuconfig. If both MMC/SD and NOR Flash are enabled, only MMC/SD will work correctly. Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-
由 Sudhakar Rajashekhara 提交于
This patch adds platform data for the 8MB NOR flash found on da850/omap-l138 EVM. Both NOR and NAND can co-exist on da850/omap-l138 as they are using different chip selects. Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-
由 Sudhakar Rajashekhara 提交于
This patch adds platform data for the 512MB NAND Flash found on DA850/OMAP-L138 EVM. Currently it supports only 1-bit ECC. Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-
由 Sudhakar Rajashekhara 提交于
There are two instances of MMC/SD on da850/omap-l138. Connector for the first instance is available on the EVM. This patch adds support for this instance. This patch also adds support for card detect and write protect switches on da850/omap-l138 EVM. Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-
由 Sudhakar Rajashekhara 提交于
This patch adds platform support for the graphic display (Sharp LK043T1DG01) found on DA850/OMAP-L138 based EVM. Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-
由 Chaithrika U S 提交于
Define resources for McASP used on DA850/OMAP-L138 EVM, add platform device defintion and Pin Mux configurations. Signed-off-by: NChaithrika U S <chaithrika@ti.com> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-
由 Sudhakar Rajashekhara 提交于
Ethernet Media Access Controller (EMAC) on da850/omap-l138 supports 10/100 Mbps operation. It also supports Media Independent Interface (MII) and Reduced Media Independent Interface (RMII) to physical layer (PHY). Phy which supports MII is present on the DA850/OMAP-L138 base board and Phy supporting RMII is present on the UI card. This patch adds support only for the MII Phy. Support for RMII Phy will be added later. Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-
由 Sudhakar Rajashekhara 提交于
Add support for the DA850/OMAP-L138 Evaluation Module (EVM) from TI. The EVM has User Interface (UI) card which contains various devices. This UI card can be connected to the base board. Support for all the devices on the UI card and ones on the EVM will be added in subsequent patches. The EVM schematics are not available publicly yet; but should be available soon. A new defconfig for this board has been added mainly because the DA830/OMAP-L137 defconfig forces writethrough cache mode which is not required on DA850/OMAP-L138. This patch has been boot tested on DA850/OMAP-L138 EVM using ramdisk as filesystem. Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-