Retries active opens for INUSE errors.

Logs any active ofld_connect_wr error replies.

Sends ofld_connect_wr on same ctrlq. It needs to go  on the same control txq as
regular CPL active/passive messages.

Retries on active open replies with EADDRINUSE.

Uses active open fw wr only if active filter region is set.

Adds stat for ofld_connect_wr failures.

This patch also adds debugfs file to show endpoints.
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

It establishes passive open connection through firmware work request. Passive
open connection will go through this path as now instead of listening server we
create a server filter which will redirect the incoming SYN packet to the
offload queue. After this driver tries to establish the connection using
firmware work request.
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

It enables establishing active open connection using fw_ofld_connection work
request when cpl_act_open_rpl says TCAM full error which may be because
of LE hash collision. Current support is only for IPv4 active open connections.

Sets ntuple bits in active open requests. For T4 firmware greater than 1.4.10.0
ntuple bits are required to be set.

Adds nocong and enable_ecn module parameter options.
Signed-off-by: NVipul Pandya <vipul@chelsio.com>

[ Move all FW return values to t4fw_api.h.  - Roland ]
Signed-off-by: NRoland Dreier <roland@purestorage.com>

It supports establishing passive open connection through firmware filter work
request. Passive open connection will go through this path as now instead of
listening server we create a server filter which will redirect the incoming SYN
packet to the offload queue.

It divides filter region into regular filters and server filter portion. It
introduces new server filter region which will be exclusively used for creating
server filters. This region will not overlap with regular filter region.

It provides new API cxgb4_alloc_sftid in LLD for getting stid in case of LE
hash collision path. This new stid will be used to open server filter in the
filter region.
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The T4 architecture is capable of filtering ingress packets at line rate
using the rule in TCAM. If packet hits a rule in the TCAM then it can be either
dropped or passed to the receive queues based on a rule settings.

This patch adds framework for managing filters and to use T4's filter
capabilities. It constructs a Firmware Filter Work Request which writes the
filter at a specified index to get the work done. It hosts shadow copy of
ingress filter entry to check field size limitations and save memory in the
case where the filter table is large.
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Implement destination MAC rule extension for L3/L4 rules in
flow steering. Usefull for vSwitch/macvlan configurations.
Signed-off-by: NYan Burman <yanb@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Get rid of full_mac, zero_mac in favour of
is_zero_ether_addr and is_broadcast_ether_addr.
Signed-off-by: NYan Burman <yanb@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 4ce45e02
"bnx2: Add BNX2 prefix to CHIP ID and name macros"

accidentally reverted 2 commits to use pci_ioumap() and to make
pci_error_handlers const.  This fixes those mistakes.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change Details:
 -      Added Stats clear counter to the bfi_enet_stats_mac structure and
        ethtool stats
 -      Modified the firmware naming convention to contain the firmware image
        version (3.1.0.0). The new convention is
        <firmware-image>-<firmware-version>.bin The change will enforce loading
        only compatible firmware with this driver and also avoid over-writing
        the old firmware image in-order to load new version driver as the
        firmware names used to be the same.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change Details:
 -      BNA state machine for Rx in start_wait state moves it to stop_wait on
        receipt of RX_E_STOP. In Rx stop_wait state, on receipt of
                RX_E_STARTED event does enet stop
                RX_E_STOPPED event does rx_cleanup_cbfn
        rx_cleanup_cbfn in this case is called without post_cbfn. post_cbfn
        happens only after RX_E_STARTED event is received in start_wait. Without
        doing post_cbfn, NAPI remains disabled and in cleanup we try to disable
        again causing endless wait. ifconfig process and other workers can thus
        get stuck.
 -      Introducing start_stop_wait state for Rx. This state handles the case of
        if post_cbfn is not done simply do stop without the cleanup.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change Details:
        Enhanced support for GRO. Page-base allocation method for Rx buffers is
used in GRO. Skb allocation has been removed in Rx path to use always warm-cache
skbs provided by napi_get_frags.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change Details:
        For Tx IB, IPM was enabled with inter_pkt_timeo of 0. This caused the
Tx IB not to generate interrupt till inter_pkt_count of packets have been
received. Correct definition for BFI_TX_INTERPKT_TIMEO & BFI_TX_INTERPKT_COUNT
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 -      Have contiguous queue pages for TxQ, RxQ and CQ. Data structure and
        QPT changes related to contiguous queue pages
 -      Optimized Tx and Rx unmap structures. Tx and Rx fast path changes due to
        unmap data structure changes
 -      Re-factored Tx and Rx fastpath routines as per the new queue data structures
 -      Implemented bnad_txq_wi_prepare() to program the opcode, flags, frame_len
        and num_vectors in the work item
 -      Reduced Max TxQ and RxQ depth to 2048 while default value for Tx/Rx queue
        depth is unaltered (512)
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 -      Remove unnecessary prefetch
 -      Simplify checking & comparison of CQ flags
 -      Dereference & store unmap_array, unmap_cons & current unmap_array
        element only once
 -      Make structures tx_config & rx_config cache line aligned.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The {read,write}s{b,w,l} operations are not defined by all
architectures and are being removed from the asm-generic/io.h
interface.

This patch replaces the usage of these string functions in the smc911x
accessors with io{read,write}{8,16,32}_rep calls instead.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ben Herrenschmidt <benh@kernel.crashing.org>
Cc: netdev@vger.kernel.org
Signed-off-by: NMatthew Leach <matthew@mattleach.net>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using netdev_alloc_frag() instead of kmalloc() permits better GRO or
TCP coalescing behavior, as skb_gro_receive() doesn't have to fallback
to frag_list overhead.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Dmitry Kravkov <dmitry@broadcom.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Acked-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The {read,write}s{b,w,l} operations are not defined by all
architectures and are being removed from the asm-generic/io.h
interface.

This patch replaces the usage of these string functions in the 8390
accessors with io{read,write}{8,16,32}_rep calls instead.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ben Herrenschmidt <benh@kernel.crashing.org>
Cc: David Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: NMatthew Leach <matthew@mattleach.net>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The {read,write}s{b,w,l} operations are not defined by all
architectures and are being removed from the asm-generic/io.h
interface.

This patch replaces the usage of these string functions in the default
DM9000 accessors with io{read,write}{8,16,32}_rep calls instead. This
is required as the dm9000 driver is in use by the blackfin
architecture which uses the asm-generic io accessors.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ben Herrenschmidt <benh@kernel.crashing.org>
Cc: David Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: NMatthew Leach <matthew@mattleach.net>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The {read,write}s{b,w,l} operations are not defined by all architectures
and are being removed from the asm-generic/io.h interface.

This patch replaces the usage of these string functions in the default
SMC accessors with io{read,write}{8,16,32}_rep calls instead, which are
defined for all architectures.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ben Herrenschmidt <benh@kernel.crashing.org>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: netdev@vger.kernel.org
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GigaMAC registers have been reported left unitialized in several
situations:
- after cold boot from power-off state
- after S3 resume

Tweaking rtl_hw_phy_config takes care of both.

This patch removes an excess entry (",") at the end of the exgmac_reg
array as well.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NWang YanQing <udknight@gmail.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers.  This patch fixes all of
them back up to be properly aligned.

Bonus is that this almost removes 100 lines of code, always a nice
surprise.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the standard #defines rather than bare numbers for PCIe Capability
ASPM fields.
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>

The get_clock() of the chelsio driver clashes with the s390 one.
The chelsio helper reads a timespec via ktime just to convert it
back to ktime. I can see no different outcome from calling
ktime_get directly.

Remove the get_clock and use ktime_get directly.
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is possible that the driver is configured to operate with a certain
link configuration which differs from the link's configuration during
boot from SAN - this would cause the driver to flap the link.

Said flap may be missed by specific switches, causing dcbx convergence
to be too long and boot sequence to fail. Convergence is longer because
switch ignores new dcbx packets due to counters mismatch, as only host
side reset the counters due to the link flap.

This patch causes the driver to ignore user's initial configuration during
boot from SAN, and continues with the existing link configuration.
Signed-off-by: NBarak Witkowski <barak@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using symbol_get(), cnic can now directly call the cnic_probe
functions in struct bnx2x and struct bnx2.  symbol_get() is not reliable
as it fails when the module is still initializing.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

by removing duplicate symbols and removing some redundant code.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

for namespace consistency.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

for namespace consistency.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

with BNX2_ prefix for namespace consistency.  Currently, these macro names
conflict with similar macros in bnx2x.h, preventing the cnic driver from
including both bnx2.h and bnx2x.h.  Including bnx2x.h in cnic.c will remove
many redundant definitions and simplify the interface.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

During MSI-X setup the system might run out of vectors. If this happens the
already assigned vectors for this NIC should be freed before trying the
disable MSI-X. Failing to do so results in the following oops.

kernel BUG at drivers/pci/msi.c:341!
[...]
Call Trace:
 [<ffffffff8128f39d>] pci_disable_msix+0x3d/0x60
 [<ffffffffa037d1ce>] igb_reset_interrupt_capability+0x27/0x5c [igb]
 [<ffffffffa037d229>] igb_clear_interrupt_scheme+0x26/0x2d [igb]
 [<ffffffffa0384268>] igb_request_irq+0x73/0x297 [igb]
 [<ffffffffa0384554>] __igb_open+0xc8/0x223 [igb]
 [<ffffffffa0384815>] igb_open+0x13/0x15 [igb]
 [<ffffffff8144592f>] __dev_open+0xbf/0x120
 [<ffffffff81443e51>] __dev_change_flags+0xa1/0x180
 [<ffffffff81445828>] dev_change_flags+0x28/0x70
 [<ffffffff814af537>] devinet_ioctl+0x5b7/0x620
 [<ffffffff814b01c8>] inet_ioctl+0x88/0xa0
 [<ffffffff8142e8a0>] sock_do_ioctl+0x30/0x70
 [<ffffffff8142ecf2>] sock_ioctl+0x72/0x270
 [<ffffffff8118062c>] do_vfs_ioctl+0x8c/0x340
 [<ffffffff81180981>] sys_ioctl+0xa1/0xb0
 [<ffffffff815161a9>] system_call_fastpath+0x16/0x1b
Code: 48 89 df e8 1f 40 ed ff 4d 39 e6 49 8b 45 10 75 b6 48 83 c4 18 5b 41 5c 41 5d 41 5e 41 5f c9 c3 48 8b 7b 20 e8 3e 91 db ff eb ae <0f> 0b eb fe 0f 1f 84 00 00 00 00 00 55 48 89 e5 0f 1f 44 00 00
RIP  [<ffffffff8128e144>] free_msi_irqs+0x124/0x130
 RSP <ffff880037503bd8>
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Given a small change to igb_init_interrupt_scheme() the function fits
igb_request_irq() for MSI/legacy interrupts initialization as well, instead of
duplicating most of its code there.

Also adding a missing igb_configure() to igb_request_irq() for MSI fallback
to work properly.
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The X540's internal thermal sensor should not be enabled for all devices, but
only those devices which enable it in the NVM image. It is expected that
actively cooled devices will have it enabled, but passively cooled devices might
not want it enabled. This is due to passively cooled devices operating very near
the thermal threshold, sometimes within the margin of error of the thermal
sensor. Thus these devices may not be good candidates for using the thermal
sensor.

This patch uses the enabled bit in the FWSM register to check whether we should
be enabling the thermal sensor, and only sets the THERMAL_SENSOR_CAPABLE flag
for those devices which have it enabled.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use the normal kernel test instead of a module specific one.
Signed-off-by: NJoe Perches <joe@perches.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If the initiator and target try to close the connection at about the same
time, there is a race condition in the termination sequence for bnx2x.
Fix the problem by waiting for the remote termination to complete before
deleting the Connection ID.  This will prevent the firmware assert.

Update version to 2.5.15.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without the reset, reloading the cnic driver can cause the iSCSI
Event Queue to be out of sync with the driver and cause intermittent
crash.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Acked-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- convert remaining htonl/ntohl +__raw_read/__raw_writel to
  swab32 + readl/writel
- add missing __iomem qualifier in myri10ge_open()
- fix  dubious: x & !y warning by switching from logical to bitwise not

The swab32 conversion fixes a bug in myri10ge_led() where
big-endian machines would write the wrong pattern.

The only remaining warning (lock context imbalance) is due to
the use of __netif_tx_trylock(), and cannot easily be fixed.
Signed-off-by: NAndrew Gallatin <gallatin@myri.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 3com driver for 3c59x requires ioport_map. Since not all
architectures support IO port mapping make 3c59x dependent on HAS_IOPORT.
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use for_each_pci_dev to simplify the code.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>