Added the product id of bcs(bar code scanner) from Diebold Procomp Brazil.
Signed-off-by: NMhayk Whandson <eu@mhayk.com.br>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds the vendor and product ID for the Alti-2 Neptune 3
(http://www.alti-2.com) which uses the FTDI chip.
Signed-off-by: NRobie Basak <rb-oss-1@justgohome.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Commit 4a90f09b added kref stuff to
ftdi_sio, but missed tty_kref_put at one exit point in
ftdi_process_read.
Signed-off-by: NJim Paris <jim@jtan.com>
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We don't need the BKL here any more so it can go. In a couple of spots the
driver requirements are not clear so push the lock down into the driver.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The following patch adds in the USB PID for Ewert Energy System's CANdapter
device (CANBUS to USB-Serial which uses the FTDI 245R chipset) to the ftdi_sio
device driver.

The patch was tested successfully on Linux kernel 2.6.27 under Ubuntu.

Relevant output from /proc/bus/usb/devices (With patch installed):

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0403 ProdID=9f80 Rev= 6.00
S:  Manufacturer=Ewert Energy Systems
S:  Product=CANdapter
S:  SerialNumber=A6RGB3Z3
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr= 90mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=ftdi_sio
E:  Ad=81(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
Signed-off-by: NAndrew Ewert <andrew@ewertenergy.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Someone on rmweb reminded me this had been overlooked from ages ago..

Add the identifiers for the Sprog II USB. This is a DCC control interface
using the FTDI-SIO hardware: http://www.sprog-dcc.co.uk/. People have been
using it with insmod options for ages, this just puts it into the driver
data.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

[Folded together as one diff from 3]

It should be 'lose', not 'loose'.
Signed-off-by: NNick Andrew <nick@nick-andrew.net>
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

err() is going away, so switch to dev_err() or printk() if it's really
needed.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NPaulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add Oceanic PID to ftdi_sio driver

Oceanic dive computers (such as the VT3 --
http://www.oceanicworldwide.com/p_computers_vt3.html) all use an onboard
FTDI serial converter, with the FTDI vid and a  PID of 0xf460.  The
attached patch adds that pid to ftdi_sio; driver  connects to my VT3
after that.
Signed-off-by: NVladimir Vukicevic <vladimir@pobox.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use kref in the USB serial drivers so that we don't free tty structures
from under the URB receive handlers as has historically been the case if
you were unlucky. This also gives us a framework for general tty drivers to
use tty_port objects and refcount.

Contains two err->dev_err changes merged together to fix clashes in the
-next tree.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixes #10783
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Support for Domintell devices (FTDI FT232BM based) : DGQG and DUSB01
module.  PIDs were missing.
Signed-off-by: NGaetan Carlier <gcpatch@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

USB: ftdi_sio: Add 0x5050/0x0900 USB IDs (Papouch Quido USB 4/4)
Signed-off-by: NJaroslav Kysela <perex@perex.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Support for PHI Fisco USB to Serial data cable (FTDI FT232BM based).
PHI Fisco cable is supplied for connecting Philips Xenium 9@9++ mobile phones.
PIDs were missing.

Tested successfully with PHI Fisco Data Cable (VID/PID 0403:e40b)
Signed-off-by: NLex V. Ross <lross@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Patch adds support for Luminance Stellaris Evaluation/Development
Kits (FTDI 2232C based).
The PIDs were missing.

Successfully tested with a Stellaris LM3S8962 Evaluation kit.
Signed-off-by: NFrederik Kriewitz <frederik@kriewitz.eu>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

USB product id registration for the ELV HS485 USB adapter (www.elv.de) to
their home automation bus system. Applies to 2.6.26.
Signed-off-by: NAndre Schenk <andre@melior.s.bawue.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

USB serial likes to use port->tty back pointers for the real work it does and
to do so without any actual locking. Unfortunately when you consider hangup
events, hangup/parallel reopen or even worse hangup followed by parallel close
events the tty->port and port->tty pointers are not guaranteed to be the same
as port->tty is the active tty while tty->port is the port the tty may or
may not still be attached to.

So rework the entire API to pass the tty struct. For console cases we need
to pass both for now. This shows up multiple drivers that immediately crash
with USB console some of which have been fixed in the process.

Longer term we need a proper tty as console abstraction
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Here's a new device ID for the ftdio_sio driver.
The diff is with linus's tree as of this morning.

The device is the RigExpert Tiny USB Soundcard Transceiver Interface for ham
radio.

(I didn't actually test this. A fellow ham couldn't get the device to work, and
I suggested binding the device ID using sysfs - see
"http://jk.ufisa.uninett.no/usb/". However, he had had moved on to other things
by then. I guess adding the device ID to the kernel "on spec" won't hurt.
The relevant part of cat /proc/bus/usb/devices shows:

T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0403 ProdID=ed22 Rev= 5.00
S:  Manufacturer=FTDI
S:  Product=MixW RigExpert Tiny
S:  SerialNumber=00000000
C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=81(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=83(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
)

From: Jon K Hellan <hellan@acm.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds support for the range of PIDs
that have been allocated for FTDI based devices
at Matrix Orbital.

A small number of units have been shipped early 2008
with a faulty USB Descriptor.  Products that may have
this issue have been marked with the existing quirk to
work around the problem.
Signed-off-by: NR. Molenkamp <rmolenkamp@matrixorbital.ca>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch reverts 57833ea6
("usb-serial: pl2303: add support for RATOC REX-USB60F") and adds
support for the device to ftdi_sio driver.

Cc: Akira Tsukamoto <akirat@rd.scei.sony.co.jp>
Cc: stable <stable@kernel.org>
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add more usb device ids to the ftdi driver.

From: Peter Mack <Peter.Mack@scs-ptc.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

* endianness annotations
* endianness fixes
* missing get_unaligned/put_unaligned

It's pretty much all over the place, changes to different files are independent.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Serial-parts-Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

urb->context code cleanup
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The usb-serial core no longer checks these fields so remove them from
all of the individual drivers.  They will be removed from the usb-serial
core in a patch later in the series.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) /
(d)) but is perhaps more readable.

An extract of the semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@haskernel@
@@

#include <linux/kernel.h>

@depends on haskernel@
expression n,d;
@@

(
- (n + d - 1) / d
+ DIV_ROUND_UP(n,d)
|
- (n + (d - 1)) / d
+ DIV_ROUND_UP(n,d)
)

@depends on haskernel@
expression n,d;
@@

- DIV_ROUND_UP((n),d)
+ DIV_ROUND_UP(n,d)

@depends on haskernel@
expression n,d;
@@

- DIV_ROUND_UP(n,(d))
+ DIV_ROUND_UP(n,d)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The ftdi_sio driver has no internal locking on the dtr/rts state. Flag
that up for someone to fix.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Here is a patch that adds support for the propox jtagcable II dongle
(http://www.propox.com/products/t_117.html): their PID was missing,
therefore we were not able to have the device recognized though it uses
a standard FTDI chip.
Signed-off-by: NMirko Bordignon <mirko.bordignon@ieee.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add EM1010PC to ftdi_sio.c
Signed-off-by: NSven Andersen <s.andersen@cryonet.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Workaround for the FT232RL-based, Matrix Orbital VK204-25-USB serial port
added to the ftdi_sio driver.

The device has an invalid endpoint descriptor, which must be modified
before it can be used.
Signed-off-by: NKevin Vance <kvance@kvance.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

add missing '|'
Signed-off-by: NRoel Kluin <12o3l@tiscali.nl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

this covers the rest of the obvious cases by using the flags
and locks to guard against disconnect which were introduced
in the earlier patch against mos7720.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

People keep trying to add entries to this section of the driver for
things.  That's what the Changelog is supposed to be for, not the .c
file.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

[PATCH] ftdi_sio: add support for more FTDI based JTAG adaptors

There are more devices similar to the Olimex JTAG adaptor, in that the first
port of the FT2232C is used for JTAG, and only the second port is available as
UART.

I have thus renamed ftdi_olimex_{probe,quirk} to ftdi_jtag_{probe,quirk} and
added vendor/product ID's for the OpenMoko Neo1973 Debug Board as well as the
OOCDlink device.

I've also updated the KERN_INFO message sent to userspace to remove the word
'olimex' and an extra '\n' that was causing an empty line in dmesg.
Signed-off-by: NHarald Welte <laforge@openmoko.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Added support for the Elster Unicom III Optical Probe.
The device ID has already been added to the usb.ids file.

Cc: stable <stable@kernel.org>
Signed-off-by: NEd Beroset <beroset@mindspring.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

little patches only to add vendor/device id of ATK_16IC CCD cam for
astronomy.

From: Franco Lanza <nextime@nexlab.it>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I work with a group of people on a free home automation tool called
FHEM.  Some of the users own more than one USB-serial device by ELV. The
ftdi_sio driver has most of the ELV devices disabled by default and
needs to be re-enabled every time you get a new kernel. Additionally a
new device (EM 1010 PC - enegry monitor) is missing in the list.
Currently our users have to follow the instructions we provide at
http://www.koeniglich.de/fhem/linux.html ... However, to some users it
is too complicated to compile their own kernel module.

We are aware that you can specify one additional device using the
vendor/product option of the module. But lot's of users own more than
one device.

Cc: stable <stable@kernel.org>
Signed-off-by: NPeter Stark <peter.stark@t-online.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>