Enable CONFIG_AT803X_PHY to support AR8030/8033/8035 PHY.
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

C293PCIE board is a series of Freescale PCIe add-in cards to perform
as public key crypto accelerator or secure key management module.

 - 512KB platform SRAM in addition to 512K L2 Cache/SRAM
 - 512MB soldered DDR3 32bit memory
 - CPLD System Logic
 - 64MB x16 NOR flash and 4GB x8 NAND flash
 - 16MB SPI flash
Signed-off-by: NMingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: NPo Liu <Po.Liu@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

When using recent udev, the /dev node mount requires CONFIG_DEVTMPFS_MOUNT
is enabled in Kernel. The patch enables the option in defconfig of Freescale
QorIQ targets.

Changed defconfig list:
   arch/powerpc/configs/85xx/p1023rds_defconfig
   arch/powerpc/configs/corenet32_smp_defconfig
   arch/powerpc/configs/corenet64_smp_defconfig
   arch/powerpc/configs/mpc85xx_smp_defconfig
   arch/powerpc/configs/mpc85xx_defconfig
   arch/powerpc/configs/mpc83xx_defconfig
Signed-off-by: NZhenhua Luo <zhenhua.luo@freescale.com>
[scottwood@freescale.com: added mpc83xx and non-smp mpc85xx]
Signed-off-by: NScott Wood <scottwood@freescale.com>

Some 85xx board, for example, P1020RDB-PC has on board silicon image
PCIe to SATA controller and when booting up, the filesystem will auto mount
to the SATA disk. So enable silicon image 3132 pcie to sata controller
by default
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add CONFIG(s) required for NAND and NOR flash controller usage.
It defines MTD, Jffs2 and UBIFS file system required for controllers.

It also enables IFC controller
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

E1000 NIC is a common used Ethernet card. Enable it as default
for mpc85xx platform.

other change is due to make savedefconfig
Reported-by: NFu Jiwei <b36666@freescale.com>
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The Freescale / iVeia P1022RDK reference board is a small-factor board
with a Freescale P1022 SOC.  It includes:

1) 512 MB 64-bit DDR3-800 (max) memory
2) 8MB SPI serial flash memory for boot loader
3) Bootable 4-bit SD/MMC port
4) Two 10/100/1000 Ethernet connectors
5) One SATA port
6) Two USB ports
7) One PCIe x4 slot
8) DVI video connector
9) Audio input and output jacks, powered by a Wolfson WM8960 codec.

Unlike the P1022DS, the P1022RDK does not have any localbus devices,
presumably because of the localbus / DIU multiplexing restriction of
the P1022 SOC.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Yocto (Built by Poky 7.0) 1.2 root filesystems fail to boot,
at least over nfs, with:

Failed to mount /dev: No such device

Configuring DEVTMPFS fixes it.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

run make savedefconfig on fsl defconfigs.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NZhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Enable MTD/NOR/NAND options by default in mpc85xx_defconfig and
mpc85xx_smp_defconfig to support NOR, NAND flash.
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Freescale PowerPC and ARM/IMX families share the same SSI IP block.
The patch merges sound/soc/imx into sound/soc/fsl, so that the possible
code sharing and consolidation can happen.

This is a plain merge, except that menuconfig SND_POWERPC_SOC is added
in Kconfig for PowerPC platform as a correspondence to SND_IMX_SOC for
IMX platform.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Enable I2C char dev interface for user space testing of I2C controler.
Enable the I2C driver on 64-bit builds (corenet64_smp_defconfig) as it
was missing.
Signed-off-by: NShaveta Leekha <shaveta@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Remove the "select PHYS_64BIT" from the Kconfig entry for the P1022DS,
so that large physical address support is a selectable option for non-CoreNet
reference boards.

The option is enabled in mpc85xx_[smp_]defconfig so that the default is
unchanged.  However, now it can be deselected.

The P1022DS had this option defined because the default device tree for
this board uses 36-bit addresses.  This had the side-effect of forcing
this option on for all boards that use mpc85xx_[smp_]defconfig.  Some
users may want to disable this feature to create an optimized configuration
for boards with <= 2GB of RAM.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

corenet64_smp_defconfig:
 - enabled rapidio

corenet32_smp_defconfig:
 - enabled hugetlbfs, rapidio

mpc85xx_smp_defconfig:
 - enabled P1010RDB, hugetlbfs, SPI, SDHC, Crypto/CAAM

mpc85xx_smp_defconfig:
 - enabled hugetlbfs, SPI, SDHC, Crypto/CAAM
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NBecky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Results from updates via make savedefconfig.
Signed-off-by: NBecky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Move the driver to the place where it is expected to be nowadays. Also
rename its CONFIG-name to match the rest and adapt the defconfigs.
Finally, move selection of REQUIRE_GPIOLIB or WANTS_OPTIONAL_GPIOLIB to
the platforms, because this option is per-platform and not per-driver.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>

Enable the audio drivers in the non-corenet 85xx defconfigs so that audio
is enabled on the Freescale P1022DS reference board.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

P1010RDB Overview
 -----------------
 1Gbyte DDR3 (on board DDR)
 32Mbyte 16bit NOR flash
 32Mbyte SLC NAND Flash
 256 Kbit M24256 I2C EEPROM
 128 Mbit SPI Flash memory
 I2C Board 128x8 bit memory
 SD/MMC connector to interface with the SD memory card
 2 SATA interface
         1 internal SATA connect to 2.5. 160G SATA2 HDD
         1 eSATA connector to rear panel
 USB 2.0
         x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface.
         x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet
 eTSEC1: Connected to RGMII PHY VSC8641XKO
 eTSEC2: Connected to SGMII PHY VSC8221
 eTSEC3: Connected to SGMII PHY VSC8221 eCAN
 Two DB-9 female connectors for Field bus interface UART
 DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Enable framebuffer console support by default in the defconfigs for the
Freescale 85xx-based reference board.  This allows the boot messages to
be shown on the video display on the P1022DS.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The P1023 processor is an e500v2 based SoC that utilizes the DPAA
networking architecture.  This adds basic board support for non-DPAA
functionality (device tree, board file, etc).
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This debug option has no overhead other than a slight increase in
kernel size, and makes bug reports more useful.  While some end users
may prefer to save the space, as a default on a kernel config aimed
primarily at development on reference boards, it should be enabled.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Uwe Kleine-König reported:

	while working on an defconfig (arm/mx27) I noticed that just updating
	it[1] results in removing CONFIG_EEPROM_AT24=y.  The reason is that
	since commit

		v2.6.36-5965-g5f2365d8 (misc devices: do not enable by default)

	MISC_DEVICES isn't enabled anymore by default.  So all defconfigs that
	have CONFIG_SOME_SYMBOL=y (or =m) (with SOME_SYMBOL depending on
	MISC_DEVICES) but not CONFIG_MISC_DEVICES=y suffer from the same
	problem.

This restores those misc devices to the powerpc defconfigs.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de
Acked-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Uwe Kleine-König
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.

This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel.  A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).

Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: NIngo Molnar <mingo@elte.hu>
Acked-by: NDavid Woodhouse <david.woodhouse@intel.com>
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The Freescale P1022DS has an on-chip video controller called the DIU, and a
driver for this device already exists.  Update the platform file for the
P1022DS reference board to enable the driver, and update the defconfig for
Freescale MPC85xx boards to add the driver.

[Edited to resolve header add/add conflict and drop #define DEBUG.
-- broonie]
Signed-off-by: NTimur Tabi <timur@freescale.com>
Acked-by: NKumar Gala <kumar.gala@freescale.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This trims all our defconfigs using make savedefconfig
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Introduce basic support for the Freescale P1022DS reference board, based on the
Freescale BSP for this board.  This patch excludes the DIU, SSI, and MMC/SD
drivers.  Only a 36-bit DTS is provided.

Update mpc86xx_smp_defconfig and mpc85xx_defconfig to support the P1022DS.
This means enabling 64-bit physical address support, increasing the maximum
zone order to 12 (to allow the DIU driver to allocate large chunks), and
clean up the audio options to disable the deprecated OSS support.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

a recent fc11 udev update on an 83xx board made root console login
disappear:

  Updating       : udev-141-8.fc11.ppc                                    32/83
udev: starting version 141
udev: deprecated sysfs layout; update the kernel or disable CONFIG_SYSFS_DEPRECATED;
	some udev features will not work correctly

and sure enough, turning off SYSFS_DEPRECATED brings the login prompt back.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Updated mpc85xx_{smp_}defconfig to enable:
* XES_MPC85xx board
* PCI MSI
* RapidIO
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add support for the P2020RDB reference board from Freescale.

Overview of P2020RDB platform
	- DDR
	  DDR2 1G
	- NOR Flash
	  16MByte
	- NAND Flash
	  32MByte
	- 3 Ethernet interfaces
	  1) etSEC1
		- RGMII
		- connected to a 5 port Vitesse Switch(VSC7385)
		- Switch is memory mapped through eLBC interface(CS#2)
		- IRQ1
	  2) etSEC2
		- SGMII
		- connected to VSC8221
		- IRQ2
	  3) etSEC3
		- RGMII
		- connected to VSC8641
		- IRQ3
	- 2 1X PCIe interfaces
	- SD/MMC ,USB
	- SPI EEPROM
	- Serial I2C EEPROM
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

* Add new 85xx boards
* Added QE/FSL gpio
* Enabled PHY drivers that exist on various boards
* Enabled FS_ENET & UCC ethernet drivers (CPM2 & QE)
* FSL HW Crypto Engine
* CPM I2C
* QE Serial
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Now that all EEPROM drivers live in the same place, let's harmonize
their symbol names.

Also fix eeprom's dependencies, it definitely needs sysfs, and is no
longer experimental after many years in the kernel tree.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>