Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ->cable_detect method to ide_hwif_t.

* Call the new method in ide_init_port() if:
  - the host supports UDMA modes > UDMA2 ('hwif->ultra_mask & 78')
  - DMA initialization was successful (if hwif->dma_base is not set
    ide_init_port() sets hwif->ultra_mask to zero)
  - "idex=ata66" is not used ('hwif->cbl != ATA_CBL_PATA40_SHORT')

* Convert PCI host drivers to use ->cable_detect method.

While at it:

* Factor out cable detection to separate functions (if not already done).

* hpt366.c/it8213.c/slc90e66.c:
  - don't check cable type if "idex=ata66" is used

* pdc202xx_new.c:
  - add __devinit tag to pdcnew_cable_detect()

* pdc202xx_old.c:
  - rename pdc202xx_old_cable_detect() to pdc2026x_old_cable_detect()
  - add __devinit tag to pdc2026x_old_cable_detect()
Reviewed-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Remove 'struct pci_dev *dev' argument from ide_hwif_setup_dma().

* Un-static ide_hwif_setup_dma() and add CONFIG_BLK_DEV_IDEDMA_PCI=n version.

* Add 'const struct ide_port_info *d' argument to ide_device_add[_all]().

* Factor out generic ports init from ide_pci_setup_ports() to ide_init_port(),
  move it to ide-probe.c and call it in in ide_device_add_all() instead of
  ide_pci_setup_ports().

* Move ->mate setup to ide_device_add_all() from ide_port_init().

* Add IDE_HFLAG_NO_AUTOTUNE host flag for host drivers that don't enable
  ->autotune currently.

* Setup hwif->chipset in ide_init_port() but iff pi->chipset is set
  (to not override setup done by ide_hwif_configure()).

* Add ETRAX host handling to ide_device_add_all().

* cmd640.c: set IDE_HFLAG_ABUSE_* also for CONFIG_BLK_DEV_CMD640_ENHANCED=n.

* pmac.c: make pmac_ide_setup_dma() return an error value and move DMA masks
  setup to pmac_ide_setup_device().

* Add 'struct ide_port_info' instances to legacy host drivers, pass them to
  ide_device_add() calls and then remove open-coded ports initialization.
Reviewed-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Setup ->mate and ->channel in ide_pci_setup_ports() instead of
  in ide_hwif_configure().

* Make 'port' parameter for ide_hwif_configure() 'unsigned int'.

* Separate PCI specific init from generic init in ide_pci_setup_ports().
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Always set DMA masks in ide_pci_setup_ports() to make sure that the valid
masks for a host are set.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Nowadays IDE core always provides drive ID and ide-disk always setups
drive->capacity64 so this quirk is no longer needed.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Don't override the cable type if the "idex=ata66" parameter was used.

While at it:

* atiixp.c: factor out cable detection to atiixp_cable_detect() from
  init_hwif_atiixp().

* cs5535.c: pass 'ide_hwif_t *hwif' instead of 'struct pci_dev *dev' to
  cs5535_cable_detect().

* scc_pata.c: factor out cable detection to scc_cable_detect() from
  init_hwif_scc() and remove incorrect comment.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The host driver must set hwif's ->no_io_32bit setting not drive's one
(ide_port_tune_devices() overrides drive's setting).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

On DTC2278 32-bit I/O has to be enabled for both devices on the port
so always enable it during init time and disallow further changes.

Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NAnton Vorontsov <cbou@mail.ru>

Signed-off-by: NAnton Vorontsov <cbou@mail.ru>

- handle spurious interrupts correctly;
- get rid of pda_power_supplies array, use two variables instead;
- factor out psy_changed() function, it will be used for polling.
Signed-off-by: NAnton Vorontsov <cbou@mail.ru>

It's pretty dummy, but useful for batteries for which we can only
get voltages.
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: NAnton Vorontsov <cbou@mail.ru>

Add suspend/resume/wakeup support for pda_power.
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: NAnton Vorontsov <cbou@mail.ru>

Add LiMn (one of the most common for small non-rechargable batteries)
battery technology and voltage_min/_max properties support.
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: NAnton Vorontsov <cbou@mail.ru>

Currently pda-power adds both ac and usb power supply units.
This patch fixes it so that psu are added only if they are enabled.
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: NAnton Vorontsov <cbou@mail.ru>

In power_supply_create_attrs(), we create static attributes as referenced
by power_supply_static_attrs[i].  After that, if we fail, we unregister
via power_supply_static_attrs[psy->properties[i]].  This is incorrect, as
psy->properties has absolutely no bearing on static attribs.  This patch
fixes it to unregister the correct attrib.

Another line which was unnecessarily line wrapped is also unwrapped.
Signed-off-by: NAndres Salomon <dilinger@debian.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

The CAPACITY_LEVEL stuff defines various levels of charge; however, what
is the difference between them?  What differentiates between HIGH and NORMAL,
LOW and CRITICAL, etc?

As it appears that these are fairly arbitrary, we end up making such policy
decisions in the kernel (or in hardware).  This is the sort of decision that
should be made in userspace, not in the kernel.

If the hardware does not support _CAPACITY and it cannot be easily calculated,
then perhaps the driver should register a custom CAPACITY_LEVEL attribute;
however, userspace should not become accustomed to looking for such a thing,
and we should certainly not encourage drivers to provide CAPACITY_LEVEL
stubs.

The following removes support for POWER_SUPPLY_PROP_CAPACITY_LEVEL.  The
OLPC battery driver is the only driver making use of this, so it's
removed from there as well.
Signed-off-by: NAndres Salomon <dilinger@debian.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Use kasprintf instead of kmalloc()-strcpy()-strcat().

Cc: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NAnton Vorontsov <cbou@mail.ru>

Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAnton Vorontsov <cbou@mail.ru>

Make acpi_sleep_prepare() static and cause it to print a message
specifying the ACPI system sleep state to be entered (helpful for
debugging the suspend/hibernation code).
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NLen Brown <len.brown@intel.com>

The ACPI 1.0 specification wants us to put devices into low power
states after executing the _PTS global control method, while ACPI
2.0 and later want us to do that in the reverse order.  The current
hibernation code follows ACPI 2.0 in that respect which may cause some
ACPI 1.0x systems to hang during hibernation (ref.
http://bugzilla.kernel.org/show_bug.cgi?id=9528).

Make the hibernation code execute _PTS before putting devices into
low power states (ie. in accordance with ACPI 1.0x) with the
possibility to override that using the 'acpi_new_pts_ordering' kernel
command line option.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLen Brown <len.brown@intel.com>

Introduce global hibernation callback .end() and rename global
hibernation callback .start() to .begin(), in analogy with the
recent modifications of the global suspend callbacks.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLen Brown <len.brown@intel.com>

The ACPI 1.0 specification wants us to put devices into low power
states after executing the _PTS global control method, while ACPI
2.0 and later want us to do that in the reverse order.  The current
suspend code follows ACPI 2.0 in that respect which causes some
ACPI 1.0x systems to hang during suspend (ref.
http://bugzilla.kernel.org/show_bug.cgi?id=9528).

Make the suspend code execute _PTS before putting devices into low
power states (ie. in accordance with ACPI 1.0x) and provide a command
line option to override the default if need be.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLen Brown <len.brown@intel.com>

The preparation to enter an ACPI system sleep state is now tied to
the disabling of GPEs, but the GPEs should not be disabled before
suspending devices.  Since on ACPI 1.0x systems the _PTS global
control method should be executed before suspending devices, we
need to disable GPEs separately.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NLen Brown <len.brown@intel.com>

The execution of ACPI global control methods _GTS and _BFS is
currently tied to the preparation to enter a sleep state and to the
leaving of the sleep state, respectively.  However, these functions
are called before disabling the nonboot CPUs and after enabling
them, respectively (in fact, on ACPI 1.0x systems the first of them
ought to be called before suspending devices), while according to the
ACPI specification, _GTS is to be executed right prior to entering
the system sleep state and _BFS is to be executed right after the
platfor firmware has returned control to the OS on wake up.

Move the execution of _GTS and _BFS to the right places.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NLen Brown <len.brown@intel.com>

On ACPI systems the target state set by acpi_pm_set_target() is
reset by acpi_pm_finish(), but that need not be called if the
suspend fails.  All platforms that use the .set_target() global
suspend callback are affected by analogous issues.

For this reason, we need an additional global suspend callback that
will reset the target state regardless of whether or not the suspend
is successful.  Also, it is reasonable to rename the .set_target()
callback, since it will be used for a different purpose on ACPI
systems (due to ACPI 1.0x code ordering requirements).

Introduce the global suspend callback .end() to be executed at the
end of the suspend sequence and rename the .set_target() global
suspend callback to .begin().
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLen Brown <len.brown@intel.com>

Wakeup GPE hasn't a handler. If system is waked up by such GPE like a
USB hotplug, I saw a lot of error reporting the GPE hasn't handler.
acpi_leave_sleep_state will clear the GPE but it's too late, we should
do it before interrupt is re-enabled.
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLen Brown <len.brown@intel.com>

When trying to debug a suspend failure I started implementing
PM_TRACE for powerpc. I then noticed that I'm debugging a suspend
failure and so PM_TRACE isn't useful at all, but thought that
nonetheless this could be useful in the future.

Basically, to support PM_TRACE, you add a Kconfig option that
selects PM_TRACE and provides the infrastructure as per the
help text of PM_TRACE.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLen Brown <len.brown@intel.com>

Some code in acpi_hibernation_finish() was moved to acpi_hibernation_leave(),
but the old copy had been left (it's harmless, but also useless).  Remove it.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLen Brown <len.brown@intel.com>

This moves the pci_bus class device to be a real struct device and at
the same time, place it in the device tree in the correct location.

Note, the old "bridge" symlink is now gone, but this was a non-standard
link and no userspace program used it.  If you need to determine the
device that the bus is on, follow the standard device symlink, or walk
up the device tree.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixes a few coding style issues in the internal pci.h file
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

PCI Express ASPM defines a protocol for PCI Express components in the D0
state to reduce Link power by placing their Links into a low power state
and instructing the other end of the Link to do likewise. This
capability allows hardware-autonomous, dynamic Link power reduction
beyond what is achievable by software-only controlled power management.
However, The device should be configured by software appropriately.
Enabling ASPM will save power, but will introduce device latency.

This patch adds ASPM support in Linux. It introduces a global policy for
ASPM, a sysfs file /sys/module/pcie_aspm/parameters/policy can control
it. The interface can be used as a boot option too. Currently we have
below setting:
        -default, BIOS default setting
        -powersave, highest power saving mode, enable all available ASPM
state
and clock power management
        -performance, highest performance, disable ASPM and clock power
management
By default, the 'default' policy is used currently.

In my test, power difference between powersave mode and performance mode
is about 1.3w in a system with 3 PCIE links.
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If the fakephp driver is used to emulate removal of a PCI device by
writing text string "0" to the "power" sysfs attribute file, this causes
its parent directory and its contents (including the "power" file) to be
deleted before the write operation returns.  Unfortunately, it ends up
in a deadlock waiting for itself to complete.

The deadlock is as follows: sysfs_write_file calls flush_write_buffer
which calls sysfs_get_active_two before calling power_write_file in
pci_hotplug_core.c via the sysfs store operation. The power_write_file
function calls disable_slot in fakephp.c via the slot operation.  The
disable_slot function calls remove_slot which calls pci_hp_deregister
(back in pci_hotplug_core.c) which calls fs_remove_slot which calls
sysfs_remove_file to remove the "power" file. The sysfs_remove_file
function calls sysfs_hash_and_remove which calls sysfs_addrm_finish
which calls sysfs_deactivate. The sysfs_deactivate function sees that
something has an active reference on the sysfs_dirent (from the
previous call to sysfs_get_active_two back up the call stack somewhere)
so waits for the active reference to go away, which is of course
impossible.

The problem has been present since 2.6.21.

This patch breaks the deadlock by queuing work queue items on a single-
threaded work queue to remove a slot from sysfs, and to rescan the PCI
buses.  There is also some protection against disabling a slot that is
already being removed.
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

SB700 SATA MSI bug will be fixed in SB700 revision A21 at hardware
level, but the SB700 revision older than A21 will also be found in the
market.  This patch modify the original quirk commit
bc38b411 instead of withdrawing it.
The patch also removes quirk to 0x4395 because 0x4395 is SB800 device
ID.
Signed-off-by: NShane Huang <shane.huang@amd.com>
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

According to the PCI Firmware Specification Revision 3.0 section 4.5, _OSC
should only be called on a root brdige.  Here is the relevant passage: "The
_OSC interface defined in this section applies only to Host Bridge ACPI
devices that originate PCI, PCI-X, or PCI Express hierarchies". Changed the
code to find the parent root bridge of the device and call _OSC on that.
Signed-off-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

AER is only used with PCIe devices so we should only check PCIe devices for
_OSC support.
Signed-off-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The function pci_osc_support_set() traverses every root bridge when
checking for _OSC support for a capability.  It quits as soon as it finds a
device/bridge that doesn't support the requested capability. This won't
work for systems that have mixed PCI and PCIe bridges when checking for
PCIe features.  I split this function into two -- pci_osc_support_set() and
pcie_osc_support_set(). The latter is used when only PCIe devices should be
traversed.
Signed-off-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NJan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Change access to inode thru file->f_dentry->d_inode, and add explicit
lock/unlock_kernel() calls.
Signed-off-by: NMathieu Segaud <mathieu.segaud@regala.cx>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>