Here we add the necessary device nodes required for successful device
probing and Pinctrl setup for the FSM when booting on an STiH416 (Orly2).
Acked-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by Angus Clark <angus.clark@st.com>
Acked-by: NBrian Norris <computersforpeace@gmail.com>
Acked-by: NMaxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Remove some entries from Dalmore's device tree that attempt to set some
options which aren't supported for the drive_gma pin group.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

As suggested by Olof Johansson at
http://www.spinics.net/lists/arm-kernel/msg314009.html.
It be better just keeping a "ti,keystone" top-level compatible and
just using that to probe. If so we don't have to touch the file
for new boards in the future.

So use common "ti,keystone" compatible in keystone.c for all boards.

Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

The UBIFS partition size was incorrectly defined as for 128M NAND,
but on k2hk-evm installed NAND flash size is 512M.
Hence, correct it.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

Now we have additional two SOC/boards supported, so add
make file rule so that all device tree blobs can be build
for keystone with 'make dtbs'.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

The control register range for clktsio interferes with clkaemifspi clock.
And it causes issues for NAND/AEMIF. So fix it.
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

The domain register range for clkfftc1 has to be 0x0235004c
instead of 0x023504c0.
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

The BCM28155-AP board has a bootloader that expects the camldo1
regulator to be enabled on entry. Currently, the camldo1 regulator
is disabled when no longer in use as is the case during a reboot /
warm reset. This causes the early bootloader to hang upon entry. Add
regulator-always-on to the camldo1 constraint to fix reboot.
Reported-by: NAlex Elder <elder@linaro.org>
Signed-off-by: NMatt Porter <mporter@linaro.org>
Tested-by: NAlex Elder <elder@linaro.org>

Add a dtsi to support the BCM590xx PMUs used by the BCM281xx family
of SoCs. Enable regulators for use with the dwc2 and sdhci on
bcm28155-ap.
Signed-off-by: NTim Kryger <tim.kryger@linaro.org>
Signed-off-by: NMatt Porter <mporter@linaro.org>
Reviewed-by: NMarkus Mayer <markus.mayer@linaro.org>

Add device tree files for the Broadcom BCM21664 SoC.
Signed-off-by: NMarkus Mayer <markus.mayer@linaro.org>
Signed-off-by: NMatt Porter <mporter@linaro.org>

Wolfram Sang pointed out during review of an efm32-i2c driver that the
property to specify the set of pins has a too general name. As several
other efm32 peripherals also have a similar register bit field, add an
"efm32" namespace.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

While removing the 0x prefixes in the unit addresses in reply to a review
comment, I must somehow have messed up these two. Uups.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

The Armada 385-DB board has a NAND flash, so enable it in the
devicetree and add the partitions as prepared in the factory images.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Link: https://lkml.kernel.org/r/1394742273-5113-6-git-send-email-ezequiel.garcia@free-electrons.comSigned-off-by: NJason Cooper <jason@lakedaemon.net>

The Armada 38x SoC family has a NAND controller, compatible
with the controller in Armada 370/375/XP SoCs. Add support for
it in the devicetree file.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Link: https://lkml.kernel.org/r/1394742273-5113-5-git-send-email-ezequiel.garcia@free-electrons.comSigned-off-by: NJason Cooper <jason@lakedaemon.net>

The Armada 38x SoC family has a clock provider called "Core Divider",
derived from the fixed 2 GHz main PLL clock. This is similar to the
one on A370, A375 and AXP.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Link: https://lkml.kernel.org/r/1394742273-5113-4-git-send-email-ezequiel.garcia@free-electrons.comSigned-off-by: NJason Cooper <jason@lakedaemon.net>

Armada 38x SoCs have a 2 GHz fixed main PLL that is used to feed
other clocks. This commit adds a DT representation of this clock
through a fixed-clock compatible node.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Link: https://lkml.kernel.org/r/1394742273-5113-3-git-send-email-ezequiel.garcia@free-electrons.comSigned-off-by: NJason Cooper <jason@lakedaemon.net>

The watchdog compatibles were following a different pattern than the one found
in the other devices. Now that the driver supports the right pattern, switch to
it in the DT.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Remove the properties that are not used anymore by the at91_adc driver.

Cc: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Remove the properties that are not used anymore by the at91_adc driver and fix
the atmel,adc-use-external-triggers property name.

Also, add #address-cells, #size-cells and a reg for each trigger to comply to
the ePAPR.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Remove the properties that are not used anymore by the at91_adc driver and fix
the atmel,adc-use-external-triggers property name.

Also, add #address-cells, #size-cells and a reg for each trigger to comply to
the ePAPR.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Remove the properties that are not used anymore by the at91_adc driver.

Also, add #address-cells, #size-cells and a reg for each trigger to comply to
the ePAPR.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Remove the properties that are not used anymore by the at91_adc driver.

Also, add #address-cells, #size-cells and a reg for each trigger to comply to
the ePAPR.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Remove the properties that are not used anymore by the at91_adc driver.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add support for the MMC2/SDIO WiFi Libertas (Marvell) module available
on the CM-T3530 SOM.

Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Enable DMA controller for USB
Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Summit is an expansion board for Gumstix Overo products.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Chestnut43 is an expansion board for Gumstix Overo products.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Alto35 is an expansion board for Gumstix Overo products.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Gallop43 is an expansion board for Gumstix Overo products.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Palo43 is an expansion board for Gumstix Overo products.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The LIS33DE accelerometer is used on several Gumstix expansion boards,
thus add the DT node to omap3-overo-common-peripherals.dtsi.

For the boards that do not have the accelerometer (like Tobi), mark the
status as disabled.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Gumstix expansion boards share a couple of peripherals:
- uart3 is used for the console
- AT24C01 EEPROM on i2c3

Use this file for overo-tobi.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NTony Lindgren <tony@atomide.com>

UART3 is used by expansion boards to get a tty console. Thus, the
pinmux should be defined by expansion boards, instead of being
imposed by the processor board.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add the AT24C01 EEPROM node populated on most Gumstix expansion board.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use the timings provided by omap-gpmc-smsc9221. This does not change
the timings, but it avoids code duplication.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Some devices (SMSC9217, SMSC9218 and SMSC9221 at least) have better
timings, allowing a higher transfer speed. Create a common file
with these timings.

Performance results with iperf:

- omap-gpmc-smsc911x.dtsi => 54.9 Mbps
- omap-gpmc-smsc9221.dtsi => 92.7 Mbps
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add the High-Speed USB PHY.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Acked-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

MMC2 is used by the on-board WiFi module populated on some boards
(based on Marvell Libertas 8688 SDIO). The Bluetooth is connected
to UART2.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add missing pinctrl entries for:
- i2c1
- mmc1
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add missing pinctrl entries:
- i2c3
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NTony Lindgren <tony@atomide.com>