Upto 4 Netlogic XLP SoCs can be connected over ICI links to form a
coherent multi-node system.  Each SoC has its own set of on-chip
devices including PIC.  To support this, add a per SoC stucture and
use it for the PIC and SYS block addresses instead of using global
variables.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4469Signed-off-by: NJohn Crispin <blogic@openwrt.org>

Initial code to support more than 32 cpus. The platform CPU mask
is updated from 32-bit mask to cpumask_t. Convert places that use
cpu_/cpus_ functions to use cpumask_* functions.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4464Signed-off-by: NJohn Crispin <blogic@openwrt.org>

At this point early printk is available, so debugging device tree
issues is easier.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4460Signed-off-by: NJohn Crispin <blogic@openwrt.org>

Provide a config option to embed a device tree for XLP evaluation
boards. This DTB will be used if the firmware does not pass in a
device tree pointer.
Signed-off-by: NJayachandran C <jayachandranc@netlogicmicro.com>
Patchwork: http://patchwork.linux-mips.org/patch/4103/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

Add the serial ports to the device tree and remove the platform
code for adding them.
Signed-off-by: NJayachandran C <jayachandranc@netlogicmicro.com>
Patchwork: http://patchwork.linux-mips.org/patch/4098/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

Move the function device_tree_init() from netlogic/xlp/of.c
to setup.c, and remove the wrapper functions reserve_mem_mach()
and free_mem_mach().

Remove file netlogic/xlp/of.c, and the Makefile entry for it.
Signed-off-by: NJayachandran C <jayachandranc@netlogicmicro.com>
Patchwork: http://patchwork.linux-mips.org/patch/4097/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

Probe and add devices on SoC "simple-bus" on startup. This will
in turn add devices like I2C controller that are specified in the
device tree under 'soc'.
Signed-off-by: NGanesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: NJayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3762/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add IRT to IRQ translation for the MMC and I2C IRQs.
Signed-off-by: NJayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3761/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The XLP USB controller appears as a device on the internal SoC PCIe
bus, the block has 2 EHCI blocks and 4 OHCI blocks. Change are to:

* Add files netlogic/xlp/usb-init.c and asm/netlogic/xlp-hal/usb.h
  to initialize the USB controller and define PCI fixups. The PCI
  fixups are to setup interrupts and DMA mask.
* Update include/asm/xlp-hal/{iomap.h,pic.h,xlp.h} to add interrupt
  mapping for EHCI/OHCI interrupts.
Signed-off-by: NGanesan Ramalingam <ganesanr@netlogicmicro.com>
Signed-off-by: NJayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3756/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Adds support for the XLP on-chip PCIe controller. On XLP, the
on-chip devices(including the 4 PCIe links) appear in the PCIe
configuration space of the XLP as PCI devices.

The changes are to initialize and register the PCIe controller,
enable hardware byte swap in the PCIe IO and MEM space, and to
enable PCIe interrupts.
Signed-off-by: NGanesan Ramalingam <ganesanr@netlogicmicro.com>
Signed-off-by: NJayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3760/
Patchwork: https://patchwork.linux-mips.org/patch/4104/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This code is not common enough to be in a shared file.  It is also not
used by any existing boards, so just remove it.

[ralf@linux-mips.org: Dropped removal of irq_create_of_mapping which was
already removed by abd2363f
[irq_domain/mips: Allow irq_domain on MIPS].  Moved device_tree_init() and
dependencies to its sole user, the XLP code.]
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: grant.likely@secretlab.ca
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2946/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Starting other threads in the core will change the number of
TLB entries of a CPU.  Re-calculate current_cpu_data.tlbsize
on the boot cpu after enabling and waking up other threads.

The secondary CPUs do not need this logic because the threads
are enabled on the secondary cores at wakeup and before cpu_probe.
Signed-off-by: NJayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3751/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add new processor ID to asm/cpu.h and kernel/cpu-probe.c.
Update to new CPU frequency detection code which works on XLP 3XX
and 8XX.
Signed-off-by: NJayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2971/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Create a common NMI and reset handler in smpboot.S and use this for
both XLR and XLP.  In the earlier code, the woken up CPUs would
busy wait until released, switch this to wakeup by NMI.

The initial wakeup code or XLR and XLP are differ since they are
started from different bootloaders (XLP from u-boot and XLR from
netlogic bootloader). But in both platforms the woken up CPUs wait
and are released by sending an NMI.

Add support for starting XLR and XLP in 1/2/4 threads per core.
Signed-off-by: NJayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2970/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

- Add CPU_XLP and NLM_XLR_BOARD to arch/mips/Kconfig for Netlogic XLP boards
- Update mips Makefiles to add XLP
Signed-off-by: NJayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2968/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

- Update common files to support XLP.
- Add arch/mips/include/asm/netlogic/xlp-hal for register definitions
  and access macros
- Add arch/mips/netlogic/xlp/ for XLP specific files.
Signed-off-by: NJayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2967/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>