Some drivers use internal netdev stats member to store part of their
stats, yet advertize ndo_get_stats64() to implement some 64bit fields.

Allow them to use netdev_stats_to_stats64() helper to make the copy of
netdev stats before they compute their 64bit counters.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix log messages and corrects some typos

Change logging of failure to enable MSI/MSI-X to display device's PCI
address instead of eth%d. Rectify a typo.
Signed-off-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Reviewed-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch recodes the MRRS cap for 5719 A0 devices as a PCI quirk.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Factor out the the existing allocation and free operations
so that they can be used individually.

This is to improve code readability, and also to prepare for
possible future changes like better error recovery and more
dynamic configuration (e.g on-the-fly resizing of the rings).

This change represents a straight up relocation of the existing
code into separate routines without changing any of the contained
code itself.  Local variables are relocated as necessary.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since all that include/linux/if_ppp.h does is #include <linux/ppp-ioctl.h>,
this replaces the occurrences of #include <linux/if_ppp.h> with
#include <linux/ppp-ioctl.h>.

It also corrects an error in Documentation/networking/l2tp.txt, where
it referenced include/linux/if_ppp.h as the source of some definitions
that are actually now defined in include/linux/if_pppol2tp.h.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This moves the definitions of the ioctls, constants and structures
relating to the ppp_generic interface to userspace out from if_ppp.h
to a new file, ppp-ioctl.h.  The new file has my copyright since I
designed and implemented the ppp_generic interface in the late 1990s.
None of the contents of this file comes from the original if_ppp.h
published by Carnegie Mellon University.

Of the remainder of if_ppp.h, only the PPP_MTU definition was being
used, and this replaces the uses of it with PPP_MRU (which is identical).
Therefore, this replaces the entire file with the single line

#include <linux/ppp-ioctl.h>

which clearly doesn't contain any CMU code.  Thus I have removed the
CMU copyright notice with its problematic advertising clause, and in
fact since it's only one trivial line I have not added any other
copyright notice.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This changes the copyright notices on the PPP code that I developed
in the late 1990s from being copyright The Australian National
University to copyright Paul Mackerras.  I can do this as I have an
acknowledgement in writing from the Head of the Computer Science
Department at ANU (where I worked then) that ANU does not claim any
intellectual property in this code.

While I'm at it, change the copyright notice from BSD-style to
GNU GPL like the rest of the kernel.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GRC reset causes the read DMA engine to go into a mode that breaks up
requests into 256 bytes.  A PHY reset is required to bring it back to
the normal mode.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

for weak memory model architectures to ensure that the chip will DMA
valid BD data.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Loopback on 9K packet fails because the chip has a DMA limit of 4K.  The
loopback test logic uses a single BD for simplicity.  Fix it by reducing
the jumbo packet size to the DMA limit.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes:

/home/davem/src/GIT/net-next/usr/include/linux/mdio.h:271: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the specific part which handles the PCAN-USB Pro adapter
from PEAK-System Technik (http://www.peak-system.com). The PCAN-USB Pro
adapter is a dual-channel USB 2.0 adapter compliant with CAN specifications
Tested-by: NOliver Hartkopp <socketcan@hartkopp.net>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NStephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch adds the specific part which handles the PCAN-USB adapter from
PEAK-System Technik (http://www.peak-system.com). The PCAN-USB adapter is
a sja1000 based, mono-channel USB 1.1 adapter compliant with CAN
specifications 2.0A (11-bit ID) and 2.0B (29-bit ID).
Tested-by: NOliver Hartkopp <socketcan@hartkopp.net>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NStephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch adds the core of the peak_usb driver which handles PEAK-System
Technik PCAN USB adapters. It defines the parts which are common to the
PCAN-USB adapters: can network interfaces management, network-to/from-usb
data path interface, timestamps management...
Tested-by: NOliver Hartkopp <socketcan@hartkopp.net>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NStephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch adds support to the PCAN-PC Card PCMCIA card from
PEAK-System Technik (www.peak-system.com). This card is a CAN interface
for the PC Card slot. It is available as a single or dual-channel version.
Tested-by: NOliver Hartkopp <socketcan@hartkopp.net>
Acked-by: NDominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NStephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch adds the support of some new PEAK-System PCI cards in the CAN
network sub-system. These are:

PCAN-PCIeC (PCI-ExpressCard)
PCAN-mminiPCI (mini-PCI)
PCAN-PCI (PCI next-gen)

This patch also adds the control of the blinking leds of the PCAN-PCIeC.
Tested-by: NOliver Hartkopp <socketcan@hartkopp.net>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NStephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

drivers/net/can/cc770/cc770.c included 'linux/can/dev.h' twice,
remove the duplicate.
Signed-off-by: NDanny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This fixes a bug in the sequence number validation during the initial handshake.

The code did not treat the initial sequence numbers ISS and ISR as read-only and
did not keep state for GSR and GSS as required by the specification. This causes
problems with retransmissions during the initial handshake, causing the
budding connection to be reset.

This patch now treats ISS/ISR as read-only and tracks GSS/GSR as required.
Signed-off-by: NSamuel Jero <sj323707@ohio.edu>
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>

This replaces an unjustified BUG_ON(), which could get triggered under normal
conditions: X_calc can be 0 when p > 0. X would in this case be set to the
minimum, s/t_mbi. Its replacement avoids t_ipi = 0 (unbounded sending rate).

Thanks to Jordi, Victor and Xavier who reported this.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NIan McDonald <ian.mcdonald@jandi.co.uk>

{g|s}etnumtcs() today returns a u8 that is only used by the DCB code
to verify no error occurred. Today the driver implementations return
negative error codes which end up being non-zero so the logic works
out but triggers some sparse warnings.

To fix the sparse warnings convert the return value to an int.

CC: Eilon Greenstein <eilong@broadcom.com>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

dcb netlink code calls setup_tc to init hardware traffic classes
to use for DCB. At some call sites the return values are not
checked for errors and in one case may return -EINVAL back to
the net/dcbnl.c caller which is expecting a u8.

This fixes some smatch hits and although failures are never
seen in practive its best to check return codes.
Reported-by: NDan Carenter <dan.carpenter@oracle.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBen Greear <greearb@candelatech.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The old code would += the total errors every time
stats were gathered.  Instead, keep a count of short-pkt
and long-pkt counters and then simply add them together
for the rx-over-length stat.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Conflicts:
	drivers/net/ethernet/broadcom/tg3.c

Conflicts in the statistics regression bug fix from 'net',
but happily Matt Carlson originally posted the fix against
'net-next' so I used that to resolve this.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

"num_vfs" is a u32 but we only use the high 16 bits and the low 16bits
are left as zero.  That isn't a problem for little endian systems but it
will break on big endian ones.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pch_gbe_validate_option() modifies 32 bits of memory but we pass
&hw->phy.autoneg_advertised which only has 16 bits and &hw->mac.fc
which only has 8 bits.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRoland Dreier <roland@purestorage.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add comments for ethtool_cmd::phy_address and
ethtool_cmd::mdio_support, and definitions of the flags currently
used in mdio_support.

In the mdio library, assert that its own flags continue to match those
in the ethtool interface.

In the mii library, use the ethtool flag definition and stop
including <linux/mdio.h>.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ID packing definitions are needed by userland and the register
definitions may also be useful there.

Do not export mdio_phy_id_{is_c45,prtad,devad}() as the use of bool is
problematic and it's not that useful to export only a subset of these.

Do not export MDIO_SUPPORTS_{C22,C45} directly; these flags are only
exposed to userland through struct ethtool_cmd so they should be
defined alongside that with appropriate names.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add VF spoof check to IFLA policy.  The original patch I submitted to
add the spoof checking feature to rtnl failed to add the proper policy
rule that identifies the data type and len.  This patch corrects that
oversight.  No bugs have been reported against this but it may cause
some problem for the netlink message parsing that uses the policy
table.

CC: stable@vger.kernel.org
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch corrects several comments that are either incorrect or formatted
incorrectly for multiline comments.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Correct spelling error caught with codespell.py.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to address several minor issues in
ixgbe_xmit_frame_ring.  Specifically it adds a comment explaining the TXSW
flag, and correctly wraps a line over 80 characters.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The e1000_link_stall_workaround_lv() function is always called in non-
atomic context so it should use msleep instead of mdelay.  Also, remove
unnecessary #include <linux/delay.h>.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This allows the NIC to receive packets with bad FCS
and other errors.  Good for sniffing packets on flakey
networks.

v4:  Only flax rx-over-length errors if pkt is beyond
   maximum expected packet size, not just beyond the MTU.
   This matches the existing logic for this counter.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>