The LAN_WAKE_EN is not used to determine if the device could support
WOL. It is used to signal a GPIO pin when a WOL event occurs. The WOL
still works even though it is disabled.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RTL8152 doesn't have U1U2 and U2P3 features, so use different
runtime functions for RTL812 and RTL8153 by adding autosuspend_en()
to rtl_ops.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

LINK_OFF_WAKE_EN should be cleared after autoresume, otherwise after
system suspend, the system would wake up when linking off occurs.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The rx early size should be

	(agg_buf_sz - packet size) / 8
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reset the BMU to clear the rx/tx fifo. This avoids that the unexpected
data remains in the hw.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Disable MAC clock speed down. It may casue the first control
transfer to contain the wrong data, when the power state change
from U1 to U0.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow for SS+ USB
Signed-off-by: NOliver Neukum <ONeukum@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace disable_aldps() and enable_aldps() with aldps_en().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace test_bit() followed by clear_bit() with test_and_clear_bit().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the autosuspend is enabled and occurs before system suspend, we should
wake the device before running system syspend. Then, we could change the wake
event for system suspend. Otherwise, the device would resume the system when
receiving any packet.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the reset_resume() is called, the flag of SELECTIVE_SUSPEND should be
cleared and reinitialize the device, whether the SELECTIVE_SUSPEND is set
or not. If reset_resume() is called, it means the power supply is cut or the
device is reset. That is, the device wouldn't be in runtime suspend state and
the reinitialization is necessary.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.

This patch:
  - Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
    NETIF_F_ALL_CSUM is being used as a mask).
  - Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
    use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When an interface is brought up which was previously suspended (via
runtime PM), it would hang. This happens because napi_disable is called
before napi_enable.

Solve this by avoiding napi_enable in the resume during open function
(netif_running is true when open is called, IFF_UP is set after a
successful open; netif_running is false when close is called, but IFF_UP
is then still set).

While at it, remove WORK_ENABLE check from rtl8152_open (introduced with
the original change) because it cannot happen:

 - After this patch, runtime resume will not set it during rtl8152_open.
 - When link is up, rtl8152_open is not called.
 - When link is down during system/auto suspend/resume, it is not set.

Fixes: 41cec84c ("r8152: don't enable napi before rx ready")
Link: https://lkml.kernel.org/r/20151205105912.GA1766@alSigned-off-by: NPeter Wu <peter@lekensteyn.nl>
Acked-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the runtime suspend issues result from the linking change.

Case 1:
a) link down occurs.
b) driver disable tx/rx.
c) autosuspend occurs.
d) hw linking up.
e) device suspends without enabling tx/rx.
f) couldn't wake up when receiving packets.

Case 2:
a) Nway results in linking down.
b) autosuspend occurs.
c) device suspends.
d) device may not wake up when linking up.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Split DRIVER_VERSION into NETNEXT_VERSION and NET_VERSION. Then,
according to the value of DRIVER_VERSION, we could know which
patches are used generally without comparing the source code.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The UEFI driver would enable zero length, and the Linux driver doesn't
need it. Zero length let the hw complete the transfer with length 0,
when there is no received packet. It would add the load of USB host
controller and reduce the performance.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The device reset is necessary if the hw becomes abnormal and stops
transmitting packets.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add rtl8152_pre_reset() and rtl8152_post_reset() which are used when
calling usb_reset_device(). The two functions could reduce the time
of reset when calling usb_reset_device() after probe().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adjust napi_disable() and napi_enable() to avoid r8152_poll() start
working before rx ready. Otherwise, it may have race condition for
rx_agg.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid the driver to enable WOL if the device doesn't support it.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Disable U1/U2 during initialization.
- Disable lpm when linking is on, and enable it when linking is off.
- Disable U1/U2 when enabling runtime suspend.

It is possible to let hw stop working, if the U1/U2 request occurs
during some situations. The patch is used to avoid it.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support the new USB gigabit ethernet.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This device is sold as 'NVIDIA Tegra USB 3.0 Ethernet'.
Chipset is RTL8153 and works with r8152.
Signed-off-by: NZheng Liu <zhliu@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This device is sold as 'Lenovo OneLink Pro Dock'.
Chipset is RTL8153 and works with r8152.
Signed-off-by: NVasily Titskiy <qehgt0@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This device is sold as 'Lenovo Tinkpad USB 3.0 Ethernet 4X90E51405'.
Chipset is RTL8153 and works with r8152.
Signed-off-by: NChristian Hesse <mail@eworm.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support setting the rx coalesce. Then someone could change the rx
agg timeout value through ethtool.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The rx early size is calculated with the mtu, so it has to be
re-calculated when the mtu is changed.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Separate USB_RX_EARLY_AGG into USB_RX_EARLY_TIMEOUT and USB_RX_EARLY_SIZE.

Replace r8153_set_rx_agg() with r8153_set_rx_early_timeout() and
r8153_set_rx_early_size().

Set the default timeout value according to the USB speed.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a capability which let the hw could change the settings
automatically when the power change to ON. However, the USB reset
would reset the settings to the hw default, so the driver has to
restore the relative settings. Otherwise, it would influence the
functions of the hw, and the compatibility for the USB hub and
USB host controller.

The relative settings are as following.
 - set the power down scale to 96.
 - enable the power saving function of USB 2.0.
 - disable the ALDPS of ECM mode.
 - set burst mode depending on the burst size.
 - enable the flow control of endpoint full.
 - set fifo empty boundary to 32448 bytes.
 - enable the function of exiting LPM when Rx OK occurs.
 - set the connect timer to 1.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use BIT macro to replace (1 << bits).
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

vlan_get_protocol() has been defined and use it to replace
get_protocol().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Keep NETIF_F_HW_VLAN_CTAG_RX and NETIF_F_HW_VLAN_CTAG_TX at the
same line.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is unnecessary to accress the hw register if the device is unplugged.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace (tp->speed & LINK_STATUS) with netif_carrier_ok().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set LPM timer to 500us, except for RTL_VER_04 which doesn't link at
USB 3.0.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a error occurs when submitting rx, skip the remaining submissions
and try to submit them again next time.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Read OCP register 0xa43a~0xa43b would clear some flags which the hw
would use, and it may let the device lost. However, the unit of
reading is 4 bytes. That is, it would read 0xa438~0xa43b when calling
sram_read() to read OCP_SRAM_DATA.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For ocp_write_word() and ocp_write_byte(), there is a generic_ocp_read()
which is used to read the whole 4 byte data, keep the unchanged bytes,
and modify the expected bytes. However, the "byen" could be used to
determine which bytes of the 4 bytes to write, so the action could be
removed.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace tasklet with NAPI.

Add rx_queue to queue the remaining rx packets if the number of the
rx packets is more than the request from poll().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The same macros are used for rx as well. So rename it.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>