In current vblank-wait implementation, if we turn off VGA output,
drm_wait_vblank will still wait on the disabled pipe until timeout,
because vblank on the pipe is assumed be enabled. This would cause
slow system response on some system such as moblin.

This patch resolve the issue by adding a drm helper function
drm_vblank_off which explicitly clear vblank_enabled[crtc], wake up
any waiting queue and save last vblank counter before turning off
crtc. It also slightly change drm_vblank_get to ensure that we will
will return immediately if trying to wait on a disabled pipe.
Signed-off-by: NLi Peng <peng.li@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[anholt: hand-applied for conflicts with overlay changes]
Signed-off-by: NEric Anholt <eric@anholt.net>

Only update the render-clock on transition from busy to idle and vice
versa, or else we burn a significant percentage of the cpu just rewriting
the register -- not quite as power-friendly as intended ;-)
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

Signed-off-by: NEric Anholt <eric@anholt.net>

Acked-by: NJakob Bornecrantz <jakob@vmware.com>
Acked-by: NThomas Hellström <thomas@shipmail.org>
Review-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJesse "Orange Smoothie" Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NKristian Høgsberg <krh@bitplanet.net>
Signed-off-by: NEric Anholt <eric@anholt.net>

PineView only has 2 ports for LVDS and CRT. Don't enable other
ports for it.

Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Otherwise the chip may scribble over free memory.
Signed-off-by: NKristian Høgsberg <krh@bitplanet.net>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

This also extends the mutex to cover fbc disabling, which is safe.
Signed-off-by: NKristian Høgsberg <krh@bitplanet.net>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

20ms delay is quite big and the routine isn't called in atomic context.
better use msleep to let other tasks run. This can reduce cpu time used
by Xorg, so potentially boost boot.
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

In disable sequence, all output ports on PCH have to be disabled
before PCH transcoder, but LVDS port was left always enabled. This
one fixes that by disable LVDS port properly during pipe disable
process, and resolved stability issue seen on Ironlake. Also move
panel fitting disable time just after pipe disable to align with
the spec.
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

The DPLL calculation logic for 9xx platform is changed in:
commit 652c393a
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Mon Aug 17 13:31:43 2009 -0700

    drm/i915: add dynamic clock frequency control

Maybe we will get the different M/N/P combination with that by using the
previous dpll calculation logic.

So restore the DPLL calculation logic for 9xx platform.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

If more than one mode with the same resolution defined in EDID has different
refresh rate, it is thought that the downclock is found for LVDS.
We will program the different FPx0/1 register so that we can select dynamically
between the low and high frequency.

On the g4x platform we will use the CxSR feature to switch the different
refresh rate if the LVDS downclock feature is supported.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

Somehow the case for G33 got dropped while porting from ums code.
This made a 400MHz chip into a 133MHz one which resulted in the
unnecessary enabling of double wide pipe mode which in turn
screwed up the overlay code.

Nothing else (than the overlay code) seems to be affected.

This fixes fdo.org bug #24835
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NEric Anholt <eric@anholt.net>

Need to calculate the SR watermark and enable it.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

Signed-off-by: NKristian Høgsberg <krh@redhat.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Replace the DRM_DEBUG with DRM_DEBUG_KMS in output device code.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Replace the DRM_DEBUG with DRM_DEBUG_DRIVER in generic i915 driver.
Then the debug info can be obtained by adding the boot option of
"drm.debug=0x02".

At the same time the debug info in increase/decrease clock is also
printed by using DRM_DEBUG_DRIVER instead of DRM_DEBUG_KMS.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

At least for the common case of userspace ioctls. When doing a
modeset operation, the wait is still uninterruptible. But considering
that failing to turn off the overlay when switching off the crtc it's
running on hangs the chip, it doesn't complicate matters _very_
much. There's just an unkillable X in addition to a black screen.
BUG() about it and explain in the code.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NEric Anholt <eric@anholt.net>

This implements intel overlay support for kms via a device-specific
ioctl. Thomas Hellstrom brought up the idea of a general ioctl (on
dri-devel). We've reached the conclusion that such an infrastructure
only makes sense when multiple kms overlay implementations exists,
which atm don't (and it doesn't look like this is gonna change).

Open issues:
- Runs in sync with the gpu, i.e. unnecessary waiting. I've decided
  to wait on this because the hw tends to hang when changing something
  in this area. I left some dummy functions as infrastructure.
- polyphase filtering uses a static table.
- uses uninterruptible sleeps. Unfortunately the alternatives may
  unnecessarily wedged the hw if/when we timeout too early (and
  userspace only overloaded the batch buffers with stuff worth a few
  secs of gpu time).

Changes since v1:
- fix off-by-one misconception on my side. This fixes fullscreen
  playback.
Changes since v2:
- add underrun detection as spec'ed for i965.
- flush caches properly, fixing visual corruptions.
Changes since v4:
- fix up cache flushing of overlay memory regs.
- killed require_pipe_a logic - it hangs the chip.

Tested-By: diego.abelenda@gmail.com (on a 865G)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
[anholt: Resolved against the MADVISE ioctl going in before this one]
Signed-off-by: NEric Anholt <eric@anholt.net>

It is identical to I85X. Use that one instead.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
[anholt: fix conflicts against the display function pointer stuff]
Signed-off-by: NEric Anholt <eric@anholt.net>

Render standy allows the GPU to power down the render unit when idle.
In order for this to work, it needs a page of graphics memory to save
state.  This patch allocates that page and enables the feature on
supported chipsets.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

When the ideal error range can't be reached, this will safely use
a most closed one. Clean up some dumb codes in DPLL function too.

This fixes DPLL clock issue against one monitor at 1680x1050@60hz.
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Initialize clock.vco to silence gcc.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

When coming back from DPMS or turning on a display, make sure we have
the watermarks set up before turning on the display plane, otherwise we
may get underruns.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NDirk Hohndel <hohndel@infradead.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

Turns out G4x needs to have sensible watermarks set, especially for
self-refresh enabled modes.  Add support for it.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NDirk Hohndel <hohndel@infradead.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

Must set filter selection as hardcoded coefficients for medium 3x3
filtering, which matches vbios setting for Ironlake.

This fixes display corrupt issue on HP arrandale with new vbios.

Cc: Stable Team <stable@kernel.org>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

For new stepping of PCH, the display reference clock
is fully under driver's control. This one trys to setup
all needed reference clock for different outputs. Older
stepping of PCH chipset should be ignoring this.

This fixes output failure issue on newer PCH which requires
driver to take control of reference clock enabling.

Cc: Stable Team <stable@kernel.org>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

To enable framebuffer compression on a g4x, we not only need the buffer
to tiled (X only), we also need to hold a fence register for the buffer.
Currently we only install a fence register for pre-i965s when setting up
the scanout buffer. Rather than adding some convoluted logic to
g4x_enable_fbc() to acquire a fence register, and perhaps to
g4x_disable_fbc() to release it again, we can extend the acquisition
during setup to all chipsets.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

FDI M/N calculation hasn't taken the current pipe color depth into account,
but always set as 24bpp. This one checks current pipe color depth setting,
and change FDI M/N calculation a little to use bits_per_pixel first, then
convert to bytes_per_pixel later.

This fixes display corrupt issue on Arrandle LVDS with 1600x900 panel
in 18bpp dual-channel mode.

Cc: Stable Team <stable@kernel.org>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Until we figure out the right setting for powersave features on
Ironlake, disable it for now. Also disable watermark update,
which has new registers for it on Ironlake too.
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[anholt: Resolved against the Pineview FBC changes]
Signed-off-by: NEric Anholt <eric@anholt.net>

According to the spec the LVDS_BORDER_ENABLE bit decides whether the border
data should be included in the active display and data sent to the panel.
Border should be used when in VGA centered (un-scaled) mode or when scaling
a 4:3 source image to a wide screen panel (typical 16:9).

So when the LVDS scaling is used, decide whether the LVDS_BORDER should be
enabled or not according to the current scaling mode.

At the same time fix the typo error in LVDS center scaling mode.

https://bugs.freedesktop.org/show_bug.cgi?id=23789Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
tested-by: NZhao Jian <jian.zhao@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

The previous patches had some unwanted side effects, I've fixed
the lack of 32bpp working, and fixed up 16bpp so it should also work.

this also adds the interface to allow the driver to set a preferred
console depth so for example low memory rn50 can set it to 8bpp.
It also catches 24bpp on cards that can't do it and forces 32bpp.

Tested on r100/r600/i945.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This adds support for the setcmap api and fixes the 8bpp
support at least on radeon hardware. It adds a new load_lut
hook which can be called once the color map is setup.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Commit 74dff282 exposed this unnecessary call by causing a change in
the failure path on i965 where framebuffer compression will be turned
on and off on every cursor update. If you don't have the xf86-video-intel
fix to avoid the blinking cursor effect, this is very slow.

Symptoms were a far more noticeable cursor blink with every cursor image
change combined with severe slowdown for animated cursors.
Signed-off-by: NBrian Rogers <brian@xyzw.org>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

Add support for framebuffer compression on GM45 and above.  Removes
some unnecessary I915_HAS_FBC checks as well (this is now part of the
FBC display function).
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

This patch splits out several of the display functions into a separate
display function table to avoid tons of chipset specific if..else
if..else if blocks all over.  There are more opportunities for this
(some noted in the structure defintition); so more cleanup patches will
follow.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

VGA arb requires DRM support for non-kms drivers, to turn on/off
irqs when disabling the mem/io regions.

VGA arb requires KMS support for GPUs where we can turn off VGA
decoding. Currently we know how to do this for intel and radeon
kms drivers, which allows them to be removed from the arbiter.

This patch comes from Fedora rawhide kernel.
Signed-off-by: NDave Airlie <airlied@redhat.com>

We usually don't have an SAREA, and we always want to update the FBC
status anyway, so move the update up above the various master/sarea
checks.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

A very high dotclock (e.g. 229500kHz as reported by Anton) can cause
the entries_required variable to overflow, potentially leading to a
FIFO watermark value that's too low to support the given mode.  Split
the division across the calculation to avoid this.

Cc: stable@kernel.org
Reported-by: NAnton Khirnov <wyskas@gmail.com>
Tested-by: NAnton Khirnov <wyskas@gmail.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

By handling latency variable efficiently we also get rid of this warning :

  CC [M]  drivers/gpu/drm/i915/intel_display.o
drivers/gpu/drm/i915/intel_display.c: In function ‘igd_enable_cxsr’:
drivers/gpu/drm/i915/intel_display.c:1918: warning: ‘latency’ may be used uninitialized in this function
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Due to a bogus FBC support check and failing to check for FBC support
in the right places, mode setting on non-mobile platforms could fail
and hang in the FBC disable routine.  Fix it up.

This fix highlights the need for cleanups in this area (function
pointers and better feature support checks).  Patches for that to
follow.
Tested-by: NKenny Graunke <kenny@whitecape.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>