This patch enables the L220 on the RealView/EB MPCore platform.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The kernel originally supported revB only. This patch enables revC by
default and adds a config option for building the kernel for the revB
platform. Since the SCU base address was hard-coded in the proc-v6.S
file (and only valid for RealView/EB revB), this patch also adds a
more generic support for defining the SCU information.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

	MPCore platform

This patch adds the registration of the secondary GIC on the
baseboard, together with the IRQ chaining setup.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The current implementation only assumes one GIC to be present in the
system. However, there are platforms with more than one cascaded interrupt
controllers (RealView/EB MPCore for example).
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds the support for the L210/L220 (outer) cache
controller. The cache range operations are done by index/way since L2
cache controller only accepts physical addresses.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The DMA cache handling functions take virtual addresses, but in the
form of unsigned long arguments.  This leads to a little confusion
about what exactly they take.  So, convert them to take const void *
instead.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The outer cache can be L2 as on RealView/EB MPCore platform or even L3
or further on ARMv7 cores. This patch adds the generic support for
flushing the outer cache in the DMA operations.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

According to ARM ARM, changes to the CP15 registers are only
guaranteed to be visible after an Instruction Synchronization Barrier
(ISB). This patch adds the ISB at the end of set_cr and
set_copro_access functions and also moves them further down in the
file, below the isb macro definition.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The architecture specification states that TLB operations are
guaranteed to be complete only after the execution of a DSB (Data
Synchronisation Barrier, former Data Write Barrier or Drain Write
Buffer). The branch target cache invalidation is also needed. The ISB
(Instruction Synchronisation Barrier, formerly Prefetch Flush) is
needed unless there will be a return from exception before the
corresponding mapping is used (i.e. user mappings).
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The ARM Architecture Reference Manual specifies that a prefetch flush
is needed after changing the DACR register (chapter B2.7.6).
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

There are three barriers - ISB, DMB and DSB for different
scenarious. This patch adds their definitions in the system.h file.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds support for the Gateworks Avila Network Platform in
a separate set of setup files to the IXDP425. This is necessary now
that a driver for the Avila CF card slot is available. It also adds
support for a minor variant on the Avila board known as the Loft,
which has a different number of maximum PCI devices.
Signed-off-by: NMichael-Luke Jones <mlj28@cam.ac.uk>
Signed-off-by: NDeepak Saxena <dsaxena@plexity.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

csum_fold doesn't need two assembly instructions to perform its task,
it can simply add the high and low parts together by rotating by 16
bits, and the carry into the upper-16 bits will automatically happen.

Also, since csum_tcpudp_magic() is just csum_tcpudp_nofold + csum_fold,
use those two functions to achieve this.  Also note that there is a
csum_fold() at the end of ip_fast_csum() as well, so use the real
csum_fold() there as well.

Boot tested on Versatile.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add the glue for ARM11 SMP oprofile support, which also supports the
performance monitor in the coherency unit.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The current lazy saving of the VFP registers is no longer possible
with thread migration on SMP. This patch implements a per-CPU
vfp-state pointer and the saving of the VFP registers at every context
switch. The registers restoring is still performed in a lazy way.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The Trcd* bits of the S3C24xx BANKCON6 and BANKCON7 registers are misspelled in include/asm-arm/arch-s3c2410/regs-mem.h as Trdc*.
Signed-off-by: NMatt Reimer <mreimer@vpop.net>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

GPIO bank A can only be output or a special
function, and the regs-gpio.h header has
mistakenly got this as input or output.

The mistake is carried on into the gpio.c
s3c2410_gpio_cfgpin() call which will set the
wrong value if S3C2410_GPIO_OUTPUT is passed.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

A couple of whitespace cleanups, mainly in the AT91 header files.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix two typo's where AT01_* was used instead of AT91_*.
[Patch from Wojtek Kaniewski]

Fix definition of AT91_SMC_EXNWMODE for the SAM9 processors.
[Patch from Wu Xuan]
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

fuse does not work on ARM due to cache incoherency issues - fuse wants
to use get_user_pages() to copy data from the current process into
kernel space.  However, since this accesses userspace via the kernel
mapping, the kernel mapping can be out of date wrt data written to
userspace.

This can lead to unpredictable behaviour (in the case of fuse) or data
corruption for direct-IO.

This resolves debian bug #402876
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

iop33x gpio offset is correct in include/asm-arm/arch-iop33x/iop33x.h, but
include/asm-arm/hardware/iop3xx.h adds 4.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Of the possible SSP frame formats (FRF bits in SSCR0), only SSCR0_PSP is defined. Other possible formats are Motorola SPI (0<<4), TI SSP (1<<4) and Microwire (2<<4). Attached patch adds a definition SSCR0_TISSP.
This mode is used for the sound codec attached to the PXA272 SSP1 of some HTC PDA phones.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The SSCR0_SlotsPerFrm macro writes a 3-bit value to bits [2:0], while the correct location of FRDC in SSCR0 is at bits [26:24]. This patch adds the missing "<< 24".
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

If PG_dcache_dirty is set for a page, we need to flush the source page
before performing any copypage operation using a different virtual address.

This fixes the copypage implementations for XScale, StrongARM and ARMv6.

This patch fixes segmentation faults seen in the dynamic linker under
the usage patterns in glibc 2.4/2.5.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Since iop13xx defines the PCI I/O spaces with physical resource addresses
the __io macro needs to perform the physical to virtual conversion.  I
incorrectly assumed that this would be handled by ioremap, but drivers
(like e1000) directly dereference the address returned from __io.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The ARM EABI requires doubleword (8-byte) stack alignment at all public entry
points.  The patch below makes the bFLT loader honour this.
It's always safe to start with a doubleword aligned stack so it doesn't seem
worth making this conditional on CONFIG_AEABI.

Paul
Signed-off-by: NPaul Brook <paul@codesourcery.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

As reminded in http://lkml.org/lkml/2006/12/23/26, one should use
asm/hardware.h and asm/irq.h but absent-minded devs like me tends to use
asm/arch/hardware.h and/or asm/arch/irqs.h.
This patch aims at preventing such things.

In order to make it work, I had to modify asm-arm/irq.h too so that it can
be included from assembly files.
Also, as a side effect, I had to modify some headers who were using the
asm/arch/hardware.h or asm/arch/irqs.h.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix incorrect IRQ numbering in arch-ep93xx/irqs.h (source: Applied
Data Systems 2.6.17 kernel tree.)
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

On ixp23xx, it was thought to be necessary to disable coherency to work
around certain silicon errata.  This turns out not to be the case --
none of the documented errata workarounds require disabling coherency,
and disabling coherency does not work around any existing errata.

Furthermore, all ixp23xx models do support coherency, so we should just
unconditionally enable coherency for all ixp23xx.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The phys_io/io_pg_offst machine record variables were being set
to bogus values, causing problems when enabling DEBUG_LL.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add HWCAP_CRUNCH so that the dynamic linker knows whether it can
use Crunch-optimised libraries or not.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Move adjust_cr() into arch/arm/mm/mmu.c, and move irqflags.h to
a more appropriate place in the header file.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Change the include/asm-arm/arch-s3c2410/regs-serial.h
platform data to use the prorper type (upf_t) for the
uart_flags.

Fix all the other parts of arch/arm/mach-s3c2410 to
include <linux/serial_core.h> and all other uses of
the include file.

mach-rx3715.c:101:18: warning: incorrect type in initializer (different base types)
mach-rx3715.c:101:18:    expected unsigned long [unsigned] uart_flags
mach-rx3715.c:101:18:    got restricted unsigned int [usertype] [force] <noident>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove old (and non-shared) VA addresses from the mappings
in arch/arm/mach-s3c2410/map.h and anywhere they are being
mapped in arch/arm/mach-s3c2410
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix address-space conversion errors from passing addresses
generated from include/asm-arm/arch-s3c2410/map.h by adding
an __force argument to the `void __iomem *` for all the
virtual addresses.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix address-space conversion errors from passing addresses
generated from include/asm-arm/arch-s3c2410/map.h by adding
an __force argument to the `void __iomem *` for all the
virtual addresses.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix copyright notices in include/asm-arm/arch-s3c2410
to actually have `Copyright` in the line. This patch
deals with all the core files.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix copyright notices in include/asm-arm/arch-s3c2410
to actually have `Copyright` in the line. This patch
deals with all the core files.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add:
  sys_unshare
  sys_set_robust_list
  sys_get_robust_list
  sys_splice
  sys_arm_sync_file_range
  sys_tee
  sys_vmsplice
  sys_move_pages
  sys_getcpu

Special note about sys_arm_sync_file_range(), which is implemented as:

asmlinkage long sys_arm_sync_file_range(int fd, unsigned int flags,
                                        loff_t offset, loff_t nbytes)
{
        return sys_sync_file_range(fd, offset, nbytes, flags);
}

We can't export sys_sync_file_range() directly on ARM because the
argument list someone picked does not fit in the available registers.
Would be nice if... there was an arch maintainer review mechanism for
new syscalls before they hit the kernel.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Support to change MX1 CPU frequency at runtime.
Tested on PiKRON's PiMX1 board and seems to be fully
stable up to 200 MHz end even as low as 8 MHz.
Signed-off-by: NPavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>