X722 hardware requires using the admin queue to configure RSS. This
function was previously re-written in commit e69ff813 ("i40e: rework
the functions to configure RSS with similar parameters").
However, the previous refactor did not work correctly for a few reasons

(a) it does not check whether seed is NULL before using it, resulting in
a NULL pointer dereference

[  402.954721] BUG: unable to handle kernel NULL pointer dereference at           (null)
[  402.955568] IP: [<ffffffffa0090ccf>] i40e_config_rss_aq.constprop.65+0x2f/0x1c0 [i40e]
[  402.956402] PGD ad610067 PUD accc0067 PMD 0
[  402.957235] Oops: 0000 [#1] SMP
[  402.958064] Modules linked in: ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 xt_conntrack ip_set nfnetlink ebtable_filter ebtable_
broute bridge stp llc ebtable_nat ebtables ip6table_mangle ip6table_raw ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv
6 ip6table_security ip6table_filter ip6_tables iptable_mangle iptable_raw iptable_nat nf_conntrack_ipv4_ nf_defrag_ipv4_ nf_nat_ip
v4_ nf_nat nf_conntrack iptable_security intel_rapl i86_kg_temp_thermal coretemp kvm_intel kvm irqbypass crct10dif_clMl crc32_
pclMl ghash_clMlni_intel iTCO_wdt iTCO_vendor_support shpchp sb_edac dcdbas pcspkr joydev ipmi_devintf wmi edac_core ipmi_ssif
 acpi_ad acpi_ower_meter ipmi_si ipmi_msghandler mei_me nfsd lpc_ich mei ioatdma tpm_tis auth_rpcgss tpm nfs_acl lockd grace s
unrpc ifs nngag200 i2c_algo_bit drm_kms_helper ttm drm iigbe bnx2x i40e dca mdio ptp pps_core libcrc32c fjes crc32c_intel
[  402.965563] CPU: 22 PID: 2461 Conm: ethtool Not tainted 4.6.0-rc7_1.2-ABNidQ+ #20
[  402.966719] Hardware name: Dell Inc. PowerEdge R720/0C4Y3R, BIOS 2.5.2 01/28/2015
[  402.967862] task: ffff880219b51dc0 ti: ffff8800b3408000 task.ti: ffff8800b3408000
[  402.969046] RIP: 0010:[<ffffffffa0090ccf>]  [<ffffffffa0090ccf>] i40e_config_rss_aq.constprop.65+0x2f/0x1c0 [i40e]
[  402.970339] RSP: 0018:ffff8800b340ba90  EFLAGS: 00010246
[  402.971616] RAX: 0000000000000000 RBX: ffff88042ec14000 RCX: 0000000000000200
[  402.972961] RDX: ffff880428eb9200 RSI: 0000000000000000 RDI: ffff88042ec14000
[  402.974312] RBP: ffff8800b340baf8 R08: ffff880237ada8f0 R09: ffff880428eb9200
[  402.975709] R10: ffff880428eb9200 R11: 0000000000000000 R12: ffff88042ec2e000
[  402.977104] R13: ffff88042ec2e000 R14: ffff88042ec14000 R15: ffff88022ea00800
[  402.978541] FS:  00007f84fd054700(0000) GS:ffff880237ac0000(0000) knlGS:0000000000000000
[  402.980003] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  402.981508] CR2: 0000000000000000 CR3: 000000003289e000 CR4: 00000000000406e0
[  402.983028] Stack:
[  402.984578]  0000000002000200 0000000000000000 ffff88023ffeda68 ffff88023ffef000
[  402.986187]  0000000000000268 ffff8800b340bbf8 ffff88023ffedd80 0000000088ce4f1d
[  402.987844]  ffff88042ec14000 ffff88022ea00800 ffff88042ec2e000 ffff88042ec14000
[  402.989509] Call Trace:
[  402.991200]  [<ffffffffa009636f>] i40e_config_rss+0x11f/0x1c0 [i40e]
[  402.992924]  [<ffffffffa00a1ae0>] i40e_set_rifh+0ic0/0x130 [i40e]
[  402.994684]  [<ffffffff816d54b7>] ethtool_set_rifh+0x1f7/0x300
[  402.996446]  [<ffffffff8136d02b>] ? cred_has_capability+0io6b/0x100
[  402.998203]  [<ffffffff8136d102>] ? selinux_capable+0x12/0x20
[  402.999968]  [<ffffffff8136277b>] ? security_capable+0x4b/0x70
[  403.001707]  [<ffffffff816d6da3>] dev_ethtool+0x1423/0x2290
[  403.003461]  [<ffffffff816eab41>] dev_ioctl+0x191/0io630
[  403.005186]  [<ffffffff811cf80a>] ? lru_cache_add+0x3a/0i80
[  403.006942]  [<ffffffff817f2a8e>] ? _raw_spin_unlock+0ie/0x20
[  403.008691]  [<ffffffff816adb95>] sock_do_ioctl+0x45/0i50
[  403.010421]  [<ffffffff816ae229>] sock_ioctl+0x209/0x2d0
[  403.012173]  [<ffffffff81262194>] do_vfs_ioctl+0u4/0io6c0
[  403.013911]  [<ffffffff81262829>] SyS_ioctl+0x79/0x90
[  403.015710]  [<ffffffff817f2e72>] entry_SYSCALL_64_fastpath+0x1a/0u4
[  403.017500] Code: 90 55 48 89 e5 41 57 41 56 41 55 41 54 53 48 89 fb 48 83 ec 40 4c 8b a7 e0 05 00 00 65 48 8b 04 25 28 00 00 00 48 89 45 d0 31 c0 <48> 8b 06 41 0f b7 bc 24 f2 0f 00 00 48 89 45 9c 48 8b 46 08 48
[  403.021454] RIP  [<ffffffffa0090ccf>] i40e_config_rss_aq.constprop.65+0x2f/0x1c0 [i40e]
[  403.023395]  RSP <ffff8800b340ba90>
[  403.025271] CR2: 0000000000000000
[  403.027169] ---[ end trace 64561b528cf61cf0 ]---

(b) it does not even bother to use the passed in *lut parameter which
defines the requested lookup table. Instead it uses its own round robin
table.

Fix these issues by re-writing it to be similar to i40e_config_rss_reg
and i40e_get_rss_aq.

Fixes: e69ff813 ("i40e: rework the functions to configure RSS with similar parameters", 2015-10-21)
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move this function below the two functions related to configuring RSS
via the admin queue. This helps co-locate the two functions, and made it
easier to spot a bug in the first i40e_config_rss_aq function as
compared to the i40e_get_rss_aq function.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This new firmware for the qed* adpaters fixes several issues:
 - Better blocking of malicious VFs.
 - After FLR, Tx-switching [internal routing] of packets might
   be incorrect.
 - Deletion of unicast MAC filters would sometime have side-effect
   of corrupting the MAC filters configred for a device.
It also contains fixes for future qed* drivers that *hopefully* would be
sent for review in the near future.

In addition, it would allow driver some new functionality, including:
 - Allowing PF/VF driver compaitibility with old drivers [running
   pre-8.10.5.0 firmware].
 - Better debug facilities.

This would also bump the qed* driver versions to 8.10.9.20.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An upcoming feature of IBM VNIC protocol is the ability to configure
redundant backing devices for a VNIC client. In case of a failure
on the current backing device, the driver will receive a signal
from the hypervisor indicating that a failover will occur. The driver
will then wait for a message from the backing device before
establishing a new connection.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It added reset function for RoCE driver. RoCE is a feature of hns.
In hip06 SoC, in RoCE reset process, it's needed to configure dsaf
channel reset, port and sl map info. Reset function of RoCE is
located in dsaf module, we only call it in RoCE driver when needed.

This patch is used to fix the conflict, please refer to this link:
  https://www.spinics.net/lists/linux-rdma/msg39114.htmlSigned-off-by: NWei Hu <xavier.huwei@huawei.com>
Signed-off-by: NNenglong Zhao <zhaonenglong@hisilicon.com>
Signed-off-by: NLijun Ou <oulijun@huawei.com>
Signed-off-by: NSheng Li <lisheng011@huawei.com>
Reviewed-by: NYisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAtul Gupta <atul.gupta@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new commmon infrastructure to allocate reosurces dynamically to
Upper layer driver's(ULD) when they register with cxgb4 driver and free
them during unregistering. All the queues and the interrupts for
them will be allocated during ULD probe only and freed during remove.
Signed-off-by: NAtul Gupta <atul.gupta@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It doesn't really change anything as BGMAC_CHIPCTL_1_IF_TYPE_RMII is
equal to 0. It make code a bit clener, so far when reading it one could
think we forgot to set a proper mode. It also keeps this mode code in
sync with other ones.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BCM53573 is a new series of Broadcom's SoCs. It's based on ARM and can
be found in two packages (versions): BCM53573 and BCM47189. It shares
some code with the Northstar family, but also requires some new quirks.

First of all there can be up to 2 Ethernet cores on this SoC. If that is
the case, they are connected to two different switch ports allowing some
more complex/optimized setups. It seems the second unit doesn't come
fully configured and requires some IRQ quirk.

Other than that only the first core is connected to the PHY. For the
second one we have to register fixed PHY (similarly to the Northstar),
otherwise generic PHY driver would get some invalid info.

This has been successfully tested on Tenda AC9 (BCM47189B0).
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

trivial fix to spelling mistake in dev_err message
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The division is already being done properly in efx_ef10_get_timer_config
which returns zero-on-success, unlike the old efx_ef10_get_sysclk_freq.

Fixes: d95e329a ("sfc: get timer configuration from adapter")
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While '0xdead' and '0xbeef' are "great" values, we should
use the correct SPEED_* values instead.

Fixes: 054c67d1 ("qed*: Add support for ethtool link_ksettings callbacks")
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When moving into using ethtool's link_ksetting, qed started
supplying its own bitmask of speed/capabilities, but qede
is still checking for the SUPPORTED value to determine whether
it supports pause.

Fixes: 054c67d1 ("qed*: Add support for ethtool link_ksettings callbacks")
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use atomic bitwise operations when setting and checking reset
requests. This should help with possible races in the service task.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Following a write the VFTXDCTL.ENABLE bit is set only when the Tx queue
is actually enabled, which may not happen during the configure phase even
if we waited for it. Make this check debug only since this is causing
confusion with users who notice the warning in dmesg.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Instead of the home brewed macro make use of netdev_dbg same as
the ixgbe driver.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Following a write the TXDCTL.ENABLE bit is set only when the Tx queue
is actually enabled, which may not happen during the configure phase even
if we waited for it. Make this check debug only since this is causing
confusion with users who notice the warning in dmesg.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use error "rmgr: Cannot insert RX class rule: Operation not supported" is
more meaningful than "rmgr: Cannot insert RX class rule: Unknown error 524"
Signed-off-by: NGangfeng Huang <gangfeng.huang@ni.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to allow for RX network flow classification to insert
and remove VLAN priority filter by ethtool

Example:
Add an VLAN priority filter:
$ ethtool -N eth0 flow-type ether vlan 0x6000 vlan-mask 0x1FFF action 2 loc 1

Show all filters:
$ ethtool -n eth0
4 RX rings available
Total 1 rules

Filter: 1
	Flow Type: Raw Ethernet
	Src MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
	Dest MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
	Ethertype: 0x0 mask: 0xFFFF
	VLAN EtherType: 0x0 mask: 0xffff
	VLAN: 0x6000 mask: 0x1fff
	User-defined: 0x0 mask: 0xffffffffffffffff
	Action: Direct to queue 2

Delete the filter by location:
$ ethtool -N delete 1
Signed-off-by: NRuhao Gao <ruhao.gao@ni.com>
Signed-off-by: NGangfeng Huang <gangfeng.huang@ni.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to allow for RX network flow classification to insert
and remove ethertype filter by ethtool

Example:
Add an ethertype filter:
$ ethtool -N eth0 flow-type ether proto 0x88F8 action 2

Show all filters:
$ ethtool -n eth0
4 RX rings available
Total 1 rules

Filter: 15
	Flow Type: Raw Ethernet
	Src MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
	Dest MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
	Ethertype: 0x88F8 mask: 0x0
	Action: Direct to queue 2

Delete the filter by location:
$ ethtool -N delete 15
Signed-off-by: NRuhao Gao <ruhao.gao@ni.com>
Signed-off-by: NGangfeng Huang <gangfeng.huang@ni.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to allow for RX network flow classification to insert
and remove Rx filter by ethtool. Ethtool interface has it's own rules
manager

Show all filters:
$ ethtool -n eth0
4 RX rings available
Total 2 rules
Signed-off-by: NRuhao Gao <ruhao.gao@ni.com>
Signed-off-by: NGangfeng Huang <gangfeng.huang@ni.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The patch adds driver support for sending the NCSI statistics to the
MFW. This is an asynchronous request from MFW. Upon receiving this, driver
populates the required data and send it to MFW.
Signed-off-by: NSudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch adds driver support for capturing stats ttl0_discard and
packet_too_big_discard in "ethtool -S" display.
Signed-off-by: NSudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of the platforms like zynqmp ultrascale+ has a
separate clock gate for the rx clock. Add an optional
rx_clk so that the clock can be enabled.
Signed-off-by: NShubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This enables
	ip -d l
to indicate if trust is on or off for VFs.
Signed-off-by: NSridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We shifted the locking around a bit but forgot to delete this unlock so
now it can unlock twice.

Fixes: cd3be169 ('i40e: Move the mutex lock in i40e_client_unregister')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBimmy Pujari <Bimmy.pujari@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch implements a feature change which allows using ethtool to set
RSS hash opts using less than four parameters if desired.

Change-ID: I0fbb91255d81e997c456697c21ac39cc9754821b
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NKiran Patil <kiran.patil@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When we allocate memory, we must free it. It's simple courtesy.

Change-ID: Id007294096fb53344f1a8b9a0f78eddf9853c5d6
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the bug which causes RSS to continue to work
after being disabled.  After disabling RSS, traffic would continue
to be assigned to different queues instead of falling back to a
single queue. Without this patch, attempting to disable RSS would
not work as expected. This patch fixes the bug by clearing the
lookup table used by RSS such that all traffic is assigned to a
single queue.  This patch also addresses the issue of reinstating
 the lookup table should RSS then be re-enabled.

Change-ID: Ib20c7c6a7e9f1f772bb787370f8a8c664796b141
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

VF goes through reset path during VF creation which happens to also
have notification of VF reset to client. Adding conditional check to
avoid wrongly notifying VF reset during VF creation.

Also changing the call order of VF enable, calling it after VF creation
rather than before.

Change-ID: I96eabd99deae746a2f0fc465194c886f196178ce
Signed-off-by: NAvinash Dayanand <avinash.dayanand@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is a fix for the bug i.e. unable to create iwarp device
in VF. This is a sync issue and the iwarp device open is called even
before the PCI register writes are done.

Forcing the PCI register writes to happen just before it exits the
function.

Change-ID: I60c6a2c709da89e845f2764cc50ce8b7373c8c44
Signed-off-by: NAvinash Dayanand <avinash.dayanand@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If a driver is unable to maintain all current user supplied settings
from ethtool (or other sources), it is not ok for a user request to
succeed and silently trample over previous configuration.

To that end, if you change the number of channels, it must not be
allowed to reduce the number of channels (queues) below the current
flow director filter rules targets. In this case, return -EINVAL when
a request to reduce the number of channels would do so. In addition
log a warning to the kernel buffer explaining why we failed, and report
the rules which prevent us from lowering the number of channels.

Change-ID: If41464d63d7aab11cedf09e4f3aa1a69e21ffd88
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a problem where a static analysis tool generates
a warning for "INVARIANT_CONDITION: Expression 'enabled_tc' used
in the condition always yields the same result."

Without this patch, the driver will not pass the static analysis
tool checks without generating warnings.

This patch fixes the problem by eliminating the irrelevant check
and redundant assignment for the value of enabled_tc.

Change-ID: Ia7d44cb050f507df7de333e96369d322e08bf408
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The function calls netif_set_real_num_(tx|rx)_queues, both of which
should be done only under rntl lock. Unfortunately the
i40evf_init_task did not hold the rtnl_lock as necessary. This patch
adds the locking needed.

Change-ID: Ib72a21c3ce22b71a226b16f9bbe0f5f8cc3e849b
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When we are resetting the pf stats we should also reset the RX csum
error stat.

Change-ID: I7af5ee0ec81a10f6deee1a7b8c2082ea068ef620
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When we do a reset, all the VLAN filters get added again. Therefore we also
want to reset the VLAN count to 0 or we quickly run out of filters.

Change-ID: I459f26851e22204dc8b8999928ad87cde8170119
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The client->open call in this path was not protected with the
client instance mutex, and hence the client->close can get initiated
before the open completes.

Change-Id: I0ed60c38868dd3f44966b6ed49a063d0e5b7edf5
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Using list_move() instead of list_del() + list_add().
Signed-off-by: NWei Yongjun <weiyj.lk@gmail.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>