Doing min_t(int, foo, INT_MAX) doesn't work correctly, because if foo
is bigger than INT_MAX, then when treated as a signed integer, it will
become negative and hence such an expression is just an elaborate NOP.

Fix such cases in ehca to do min_t(unsigned, foo, INT_MAX) instead.
This fixes negative reported values for max_cqe, max_pd and max_ah:

Before:

        max_cqe:                        -64
        max_pd:                         -1
        max_ah:                         -1

After:
        max_cqe:                        2147483647
        max_pd:                         2147483647
        max_ah:                         2147483647

Based on a bug report and fix from Anton Blanchard <anton@samba.org>.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Firmware commands are sent to the HCA by writing multiple words to a
command register block.  Access to this block of registers is
serialized with a mutex.  However, on large SGI systems, problems were
seen with multiple CPUs issuing FW commands at the same time, because
the writes to the register block may be reordered within the system
interconnect and reach the HCA in a different order than they were
issued (even with the mutex).  Fix this by adding an mmiowb() before
dropping the mutex.
Tested-by: NArthur Kepner <akepner@sgi.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Increase the number of QPs allowed per multicast group from 8 to 56.
This allows for one QP per core on 16-core systems, which are now
quite common, and allows some space for future growth.

This is basically the same patch that Jack Morgenstein
<jackm@dev.mellanox.co.il> just supplied for mlx4.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Implement FMRs for mlx4.  This is an adaptation of code from mthca.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NMichael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Write MTT entries directly to ICM from the driver (eliminating use of
WRITE_MTT command).  This reduces the number of FW commands needed to
register an MR by at least a factor of 2 and speeds up memory
registration significantly.  This code will also be used to implement
FMRs.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NMichael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Totally forgot this.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NHoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NHoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

display the following device information under /sys/class/infiniband/mlx4_X:
board_id, fw_ver, hw_rev, hca_type.

This patch makes this information available to userspace utilities
such as ibstat and ibv_devinfo.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

* Replace {un}register_cpu_notifier with {un}register_hotcpu_notifier
  thereby losing a couple of #ifdef HOTPLUG_CPU pairs.
* Move comp_pool_callback_nb declaration to below that of callback
  function so that initialization of .notifier_call and .priority can
  occur at build time itself and not runtime.
* Mark the notifier_block (and callback function, and another static
  function used by it) as __cpuinit{data} for the sake of consistency
  and remove enclosing #ifdef. (This may increase size for modular
  build of this module, however, because these are no longer dropped
  unconditionally now.)
Signed-off-by: NSatyam Sharma <satyam@infradead.org>
Acked-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

...because, on virtualized hardware like System p, we can't be sure
that the physical pages behind them are contiguous otherwise.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Nobody needed the SVNEHCA_ prefix anyway.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

We can use raw_smp_processor_id() here because the processor ID is
only used for debug output and therefore our use is preemption-unsafe.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Some firmware levels exhibit a race condition between H_ALLOC_RESOURCE(MR)
and H_FREE_RESOURCE(MR).  Work around this problem by locking these hvCalls
against each other.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix some modify_qp() issues related to path migration.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

...because -12 is easier to read than FFFFFFF4.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Change hvcall trace output towards better readability: reg numbers
instead of argument numbers, return code as signed decimal instead of
unsigned hex.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Use Paul's new remap_4k_pfn() function to map our 4K firmware contexts
into user space on 64K-page machines without exposing neighboring
firmware contexts. Return the context's offset within a 64K page to
user space so it can determine the proper virtual address.

For details about remap_4k_pfn(), see commit 721151d0 or
http://patchwork.ozlabs.org/linuxppc/patch?id=10281Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

These driver changes incorporate the proposed PCI-X / PCI-Express read
byte count interface.  Reading and setting those values doesn't take
place "manually", instead wrapping functions are called to allow
quirks for some PCI bridges.

Signed-off by: Peter Oruba <peter.oruba@amd.com>
Based on work by Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

At the moment the ehca module parameters are not exported in sysfs.
Export them with 0444 permissions.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Acked-by: NHoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

ehca spits out a lot of debugging information. I had to look closely to
see the "Port 1 is not active" message within all the debug:

eHCA Infiniband Device Driver (Rel.: SVNEHCA_0022)
eHCA scaling code enabled
ehca D.001.DQDXYCB-P1-C9: PU0006 EHCA_ERR:ehca_define_sqp Port 1 is not active.
ehca D.001.DQDXYCB-P1-C9: PU0006 EHCA_ERR:ehca_create_qp ehca_define_sqp() failed rc=ffffffffffffffff
ib_mad: Couldn't create ib_mad QP1
ib_mad: Couldn't open ehca0 port 1
ehca D.001.DQDXYCB-P1-C9: PU0006 EHCA_ERR:ehca_alloc_fmr unsupported fmr_attr->page_shift=9
ehca D.001.DQDXYCB-P1-C9: PU0006 EHCA_ERR:ehca_alloc_fmr rc=ffffffffffffffea pd=c000000b4b5b2420 mr_access_flags=7 fmr_attr=c0000005afd37394
fmr_create failed for FMR 0

Remove a few debug statements so that things are clearer:

eHCA Infiniband Device Driver (Rel.: SVNEHCA_0022)
eHCA scaling code enabled
ehca D.001.DQDXYCB-P1-C9: PU0006 EHCA_ERR:ehca_define_sqp Port 1 is not active.
ib_mad: Couldn't create ib_mad QP1
ib_mad: Couldn't open ehca0 port 1
ehca D.001.DQDXYCB-P1-C9: PU0006 EHCA_ERR:ehca_alloc_fmr unsupported fmr_attr->page_shift=9
fmr_create failed for FMR 0
Signed-off-by: NAnton Blanchard <anton@samba.org>
Acked-by: NHoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

mlx4_srq_query() returns a big-endian 16-bit value through an int *,
which screws up sparse checking.  Fix this so that a CPU-endian value
is returned.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Recover from MSI-X errors by automatically falling back on regular
interrupt, instead of asking the user to do this manually.  This makes
it possible to enable MSI-X by default, and will make it possible to
get rid of the msi_x module option in the future.
Signed-off-by: NMichael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

ehca_classes.h uses struct mutex, so while <linux/mutex.h> seems to be
pulled in indirectly by one of the headers it includes, the right
thing is to include <linux/mutex.h> directly.
Signed-off-by: NMichael S. Tsirkin <mst@dev.mellanox.co.il>
Acked-by: NStefan Roscher <stefan.roscher@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Use a __set_data_seg() helper in mlx4_ib_post_recv() too; in addition
to making the code easier to read, this also allows gcc to generate
better code -- on x86_64:

add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-8 (-8)
function                                     old     new   delta
mlx4_ib_post_recv                            359     351      -8
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Allow changing parameter values without having to reload the module.
This is safe because these parameters are only looked at when a new
connection is established.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This is an addendum to commit 0e6e7416 ("IB/mlx4: Handle new FW
requirement for send request prefetching").  We also need to handle
prefetch marking properly for S/G segments, or else the HCA may end up
processing S/G segments that are not fully written and end up sending
the wrong data.  This can actually cause data corruption in practice,
especially on systems with relatively slow CPUs (where the HCA is more
likely to prefetch while the CPU is in the middle of writing a work
request into memory).

We write S/G segments in reverse order into the WQE, in order to
guarantee that the first dword of all cachelines containing S/G
segments is written last (overwriting the headroom invalidation
pattern).  The entire cacheline will thus contain valid data when the
invalidation pattern is overwritten.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix ehca SRQ support so that IPoIB connected mode works:

 - Report max_srq > 0 if SRQ is supported
 - Report "last wqe reached" asynchronous event when base QP dies;
   this is required by the IB spec and IPoIB CM relies on receiving it
   when cleaning up.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The new Small QP code had a few bugs that would also make it trigger
for non-Small QPs.  Fix them.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

cxgb3 used netdev_priv() and dev->priv for different purposes.
In 2.6.23, netdev_priv() == dev->priv, cxgb3 needs a fix.
This patch is a partial backport of Dave Miller's changes in the
net-2.6.24 git branch.

Without this fix, cxgb3 crashes on 2.6.23.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

A stray semicolon makes us inadvertently ignore the value of err.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Current code has a cut-and-paste error and returns IB_WC_SEND when it
should return IB_WC_RDMA_READ.
Signed-off-by: NVu Pham <vu@mellanox.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This avoids deadlocks.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

One patch for two trivial typos of 'error' with three R's, appearing in message strings.

There's a bunch more of the same in comments, not dealt with here.
Signed-off-by: NEddy L O Jansson <eddy@klopper.net>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On some system hardware, we are seeing moderately common cases of the
chip errormask register being overwritten due to a chip bug in iba6120
that is triggered by a vendor-specific PCIe broadcast message.  This
patch merely checks periodically, and corrects it if needed (the
overwrite can cause us to not get error and hardware error
interrupts).  Also, make dd->ipath_errormask the one, true canonical
source for kr_errormask, and remove references to ipath_ignorederrs as
it is currently unused.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NJohn Gregor <john.gregor@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>