This is part of the workaround for AM35x advisory Advisory 1.1.20.
The advisory says that the IPSS bridge can't handle 8 & 16 bit read
access. An 16bit read access to MUSB_INTRTXE results in an 32bit read
access which also reads INTRRX and therefore may lose interrupts.
This patch uses a shadow register of MUSB_INTRTXE so we only perform
write access to it.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This is part of the workaround for AM35x advisory Advisory 1.1.20.
The advisory says that the IPSS bridge can't handle 8 & 16 bit read
access. An 16bit read access to MUSB_INTRRXE results in an 32bit read
access which also reads INTRUSB and therefore may lose interrupts.
This patch uses a shadow register of MUSB_INTRRXE so we only perform
write access to it.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This is part of the workaround for AM35x advisory Advisory 1.1.20.
The advisory says that the IPSS bridge can't handle 8 & 16 bit read
access. An 8bit read access to FADDR results in an 32bit read
access which also reads INTRTX and therefore may lose interrupts.
This patch removes any reads to FADDR as they are not really required.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This reverts commit 4f3e8d26.

it turns out that current implementation of Mode 1
DMA added a few regressions to some users, so we
need to revert this patch and let author work on
a better version of Mode 1 DMA support.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Remove unnecessary if condition. No change in logic.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

we are compiling the driver always with full OTG
capabilities, so that board_mode trick becomes
useless.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Do not rely on any hints from gadget drivers and use DMA mode 1
whenever we expect data of at least the endpoint's packet size and
have not yet received a short packet.

The last packet if short is always transferred using DMA mode 0.

This patch fixes USB throughput issues in mass storage mode for
host to device transfers.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This is to reduce the overhead of dma programming for zero byte
transmit as same can be done using pio mode.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In rxstate(), improper types are given to 'fifo_count' and 'len' variables, and
these variables are not used in accordance to their names (up to the certain
point), i.e. 'len' to hold the size of a packet in the RX FIFO, and 'fifo_count'
to hold a difference between 'request->length' and 'request->actual'...
Interchange the variables up to the point where their use starts to make sense
again.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

usb_ep_ops.disable must clear external copy of the endpoint descriptor,
otherwise musb crashes after loading/unloading several gadget modules
in a row:

Unable to handle kernel paging request at virtual address bf013730
pgd = c0004000
[bf013730] *pgd=8f26d811, *pte=00000000, *ppte=00000000
Internal error: Oops: 7 [#1]
Modules linked in: g_cdc [last unloaded: g_file_storage]
CPU: 0    Not tainted  (3.2.17 #647)
PC is at musb_gadget_enable+0x4c/0x24c
LR is at _raw_spin_lock_irqsave+0x4c/0x58
[<c027c030>] (musb_gadget_enable+0x4c/0x24c) from [<bf01b760>] (gether_connect+0x3c/0x19c [g_cdc])
[<bf01b760>] (gether_connect+0x3c/0x19c [g_cdc]) from [<bf01ba1c>] (ecm_set_alt+0x15c/0x180 [g_cdc])
[<bf01ba1c>] (ecm_set_alt+0x15c/0x180 [g_cdc]) from [<bf01ecd4>] (composite_setup+0x85c/0xac4 [g_cdc])
[<bf01ecd4>] (composite_setup+0x85c/0xac4 [g_cdc]) from [<c027b744>] (musb_g_ep0_irq+0x844/0x924)
[<c027b744>] (musb_g_ep0_irq+0x844/0x924) from [<c027a97c>] (musb_interrupt+0x79c/0x864)
[<c027a97c>] (musb_interrupt+0x79c/0x864) from [<c027aaa8>] (generic_interrupt+0x64/0x7c)
[<c027aaa8>] (generic_interrupt+0x64/0x7c) from [<c00797cc>] (handle_irq_event_percpu+0x28/0x178)
...

Cc: stable@vger.kernel.org # v3.1+
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

User can trigger disabling of gadget at run time while the
transfers are going on.
Eg: 1: rmmod of musb driver while transfers are going on

Eg: 2: On android doing:
 echo 0       > /sys/class/android_usb/android0/enable
While a big file transfer is going on via PTP/MTP.

In such a case, musb_gadget_disable() calls nuke()
but the dma interrupt may still happen for an endpoint since hw
would raise the interrupt in anycase.

This can result in a NULL pointer access crash:

[  314.030426] PC is at txstate+0x74/0x20c
[  314.034759] LR is at musb_g_tx+0x140/0x204
[  314.039489] pc : [<c03506f4>]    lr : [<c0350bcc>]    psr: 20000193
[  314.039520] sp : c783bc68  ip : 00000002  fp : c783bc9c
[  314.052429] r10: 00000018  r9 : 00000000  r8 : 00000200
[  314.058258] r7 : 00000000  r6 : fc0ab130  r5 : c781a410  r4 : c6caf640
[  314.065643] r3 : 00000000  r2 : 00000000  r1 : 00000000  r0 : c781a000
[  315.083251] Backtrace:
[  315.086242] [<c0350680>] (txstate+0x0/0x20c) from [<c0350bcc>] (musb_g_tx+0x140/0x204)
[  315.095123] [<c0350a8c>] (musb_g_tx+0x0/0x204) from [<c034eb00>] (musb_dma_completion+0x40/0x54)
[  315.104980] [<c034eac0>] (musb_dma_completion+0x0/0x54) from [<c0351e6c>] (dma_controller_irq+0x118/0x184)
[  315.115661] [<c0351d54>] (dma_controller_irq+0x0/0x184) from [<c00d86b8>] (handle_irq_event_percpu+0x54/0x188)

So put protection in code to handle possiblity of getting an interrupt for an
endpoint that might have been already nuked.
Reported-by: NTodd Poynor <toddpoynor@google.com>
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There's really no point in having hcd->irq as a
signed integer when we consider the fact that
IRQ 0 means NO_IRQ. In order to avoid confusion,
make hcd->irq unsigned and fix users who were
passing -1 as the IRQ number to usb_add_hcd.
Tested-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This changes the otg functions so that they receive struct
otg instead of struct usb_phy as parameter and
converts all users of these functions to pass the otg member
of their usb_phy.

Includes fixes to IMX code from Sascha Hauer.

[ balbi@ti.com : fixed a compile warning on ehci-mv.c ]
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
Acked-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: NLi Yang <leoli@freescale.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Reviewed-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use the new usb_phy_* functions with transceiver
operations instead of the old otg functions.

Includes fixes from Sascha Hauer.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: NLi Yang <leoli@freescale.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Reviewed-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

musb INDEX register is getting modified/corrupted during temporary
un-locking in a SMP system. Set this register with proper value
after re-acquiring the lock

Scenario:
---------
CPU1 is handling a data transfer completion interrupt received for
the CLASS1 EP
CPU2 is handling a CLASS2 thread which is queuing data to musb for
transfer

Below is the error sequence:

         CPU1                   |             CPU2
--------------------------------------------------------------------
Data transfer completion inter- |
rupt recieved.                  |
                                |
musb INDEX reg set to CLASS1 EP |
                                |
musb LOCK is acquired.          |
                                |
                                | CLASS2 thread queues data.
                                |
                                | CLASS2 thread tries to acquire musb
                                | LOCK but lock is already taken by
                                | CLASS1, so CLASS2 thread is
                                | spinning.
                                |
From Interrupt Context musb     |
giveback function is called     |
                                |
The giveback function releases  | CLASS2 thread now acquires LOCK
LOCK                            |
                                |
ClASS1 Request's completion cal-| ClASS2 schedules the data transfer and
lback is called                 | sets the MUSB INDEX to Class2 EP number
                                |
Interrupt handler for CLASS1 EP |
tries to acquire LOCK and is    |
spinning                        |
                                |
Interrupt for Class1 EP acquires| Class2 completes the scheduling etc and
the MUSB LOCK                   | releases the musb LOCK
                                |
Interrupt for Class1 EP schedul-|
es the next data transfer       |
but musb INDEX register is still|
set to CLASS2 EP                |

Since the MUSB INDEX register is set to a different endpoint, we
read and modify the wrong registers. Hence data transfer will not
happen properly. This results in unpredictable behavior

So, the MUSB INDEX register is set to proper value again when
interrupt re-acquires the lock

Cc: stable@vger.kernel.org
Signed-off-by: NSupriya Karanth <supriya.karanth@stericsson.com>
Signed-off-by: NPraveena Nadahally <praveen.nadahally@stericsson.com>
Reviewed-by: Nsrinidhi kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use struct usb_otg members with OTG specific functions instead
of usb_phy members.

[ balbi@ti.com: added a missing change on musb_gadget.c to avoid
	a compile error on a later patch ]
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There's really no point in doing all that
initcall trickery when we can safely let
udev handle module probing for us.

Remove all of that trickery, by moving everybody
to module_init() and making proper use of
platform_device_register() rather than
platform_device_probe().
Tested-by: NRajashekhara, Sudhakar <sudhakar.raj@ti.com>
Tested-by: NTasslehoff Kjappfot <tasskjapp@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Remove a few unnecessary headers from a
few files.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This commit renames the “speed” field of the usb_gadget_driver
structure to “max_speed”.  This is so that to make it more
apparent that the field represents the maximum speed gadget
driver can support.

This also make the field look more like fields with the same
name in usb_gadget and usb_composite_driver structures.  All
of those represent the *maximal* speed given entity supports.

After this commit, there are the following fields in various
structures:
* usb_gadget::speed - the current connection speed,
* usb_gadget::max_speed - maximal speed UDC supports,
* usb_gadget_driver::max_speed - maximal speed gadget driver
  supports, and
* usb_composite_driver::max_speed - maximal speed composite
  gadget supports.
Signed-off-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This commit replaces usb_gadget's is_dualspeed field with
a max_speed field.

[ balbi@ti.com : Fixed DWC3 driver ]
Signed-off-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Several UDC drivers had a gadget driver's speed sanity check of the
form of:

	driver->speed != USB_SPEED_HIGH

or:

	driver->speed != USB_SPEED_HIGH && driver->speed != USB_SPEED_FULL

As more and more gadget drivers support USB SuperSpeed, driver->speed
may be set to USB_SPEED_SUPER and UDC driver should handle such gadget
correctly.  The above checks however fail to recognise USB_SPEED_SUPER
as a valid speed.

This commit changes the two checks to:

	driver->speed < USB_SPEED_HIGH

or:

	driver->speed < USB_SPEED_FULL

respectively.
Signed-off-by: NMichal Nazarewicz <mina86@mina86.com>
Reported-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

that has already being done by udc-core.c. It's
unnecessary and might cause issues with some gadget
drivers.

Tested: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NJustin P. Mattock <justinmattock@gmail.com>
Signed-off-by: NVitaliy Ivanov <vitalivanov@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This patch enables DMA mode1 for the RX path when we know
there won't be any short packets. We check that by looking
into the short_no_ok flag, if it's true we enable mode1, otherwise
we use mode0 to transfer the data.

This will result in a throughput performance gain of around
40% for USB mass-storage/mtp use cases.

[ balbi@ti.com : updated commit log and code comments slightly ]
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NMoiz Sonasath <m-sonasath@ti.com>
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Tested-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Now ${LINUX}/drivers/usb/* can use usb_endpoint_maxp(desc) to get maximum packet size
instead of le16_to_cpu(desc->wMaxPacketSize).
This patch fix it up

Cc: Armin Fuerst <fuerst@in.tum.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Johannes Erdfelt <johannes@erdfelt.com>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: David Kubicek <dave@awk.cz>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Brad Hards <bhards@bigpond.net.au>
Acked-by: NFelipe Balbi <balbi@ti.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Thomas Dahlmann <dahlmann.thomas@arcor.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: David Lopo <dlopo@chipidea.mips.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Xie Xiaobo <X.Xie@freescale.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Jiang Bo <tanya.jiang@freescale.com>
Cc: Yuan-hsin Chen <yhchen@faraday-tech.com>
Cc: Darius Augulis <augulis.darius@gmail.com>
Cc: Xiaochen Shen <xiaochen.shen@intel.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: OKI SEMICONDUCTOR, <toshiharu-linux@dsn.okisemi.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Herbert Pötzl <herbert@13thfloor.at>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Roman Weissgaerber <weissg@vienna.at>
Acked-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: Florian Floe Echtler <echtler@fs.tum.de>
Cc: Christian Lucht <lucht@codemercs.com>
Cc: Juergen Stuber <starblue@sourceforge.net>
Cc: Georges Toth <g.toth@e-biz.lu>
Cc: Bill Ryder <bryder@sgi.com>
Cc: Kuba Ober <kuba@mareimbrium.org>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In case one "forgot" to load the receiver i.e. doing
|modprobe omap2430
|modprobe musb_hdrc

he ends up with:

|musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
|HS USB OTG: no transceiver configured
|musb-hdrc musb-hdrc: musb_init_controller failed with status -19
|(NULL device *): gadget not registered.
|Unable to handle kernel NULL pointer dereference at virtual address 0000001c
|Internal error: Oops: 17 [#1] SMP
|[<c011383c>] (sysfs_find_dirent+0x4/0x60) from [<c01138c0>] (sysfs_get_dirent+0x28/0x78)
|[<c01138c0>] (sysfs_get_dirent+0x28/0x78) from [<c0115b78>] (sysfs_unmerge_group+0x1c/0x90)
|[<c0115b78>] (sysfs_unmerge_group+0x1c/0x90) from [<c0179ba4>] (dpm_sysfs_remove+0x14/0x3c)
|[<c0179ba4>] (dpm_sysfs_remove+0x14/0x3c) from [<c01742f8>] (device_del+0x40/0x1b4)
|[<c01742f8>] (device_del+0x40/0x1b4) from [<c0174478>] (device_unregister+0xc/0x18)
|[<c0174478>] (device_unregister+0xc/0x18) from [<bf0489b4>] (musb_free+0x24/0x88 [musb_hdrc])
|[<bf0489b4>] (musb_free+0x24/0x88 [musb_hdrc]) from [<bf057d18>] (musb_probe+0xb50/0xe3c [musb_hdrc])
|[<bf057d18>] (musb_probe+0xb50/0xe3c [musb_hdrc]) from [<c01779c4>] (platform_drv_probe+0x1c/0x24)

The problem is that musb_free() tries to figure out what was
initializued and what wasn't and clean up only the initialized part.
This works well for usb_del_gadget_udc() but device_unregister() can't
deal with it. Therefore we rely on the fact the we always have a parent
device and only then remove the device.
I broke this in 0f91349b ("usb: gadget: convert all users to the new udc
infrastructure")
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

an 'unhandled fault' is causes when a gadget driver calls
usb_gadget_connect() while the USB cable isn't plugged into
the OTG port.

the fault is caused by an access to MUSB's memory space
while its clock is turned off due to pm_runtime kicking
in.

in order to fix the fault, we enclose musb_gadget_pullup()
with pm_runtime_get_sync() ... pm_runtime_put() calls to
be sure we will always reach that path with clock turned on.

[ balbi@ti.com : simplified commit log; removed few things
	which didn't belong there ]

Cc: stable@kernel.org
Reported-by: NZach Pfeffer <zach.pfeffer@linaro.org>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

an 'unhandled fault' is causes when a gadget driver calls
usb_gadget_connect() while the USB cable isn't plugged into
the OTG port.

the fault is caused by an access to MUSB's memory space
while its clock is turned off due to pm_runtime kicking
in.

in order to fix the fault, we enclose musb_gadget_pullup()
with pm_runtime_get_sync() ... pm_runtime_put() calls to
be sure we will always reach that path with clock turned on.

[ balbi@ti.com : simplified commit log; removed few things
	which didn't belong there ]

Cc: stable@kernel.org
Reported-by: NZach Pfeffer <zach.pfeffer@linaro.org>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

udc-core checks for valid callbacks so there is no need for the driver
to do so. Also "can-be-bound-once" is verified by udc-core. The pull-up
callback is called by udc-core afterwords.

[ balbi@ti.com : keep holding gadget_driver pointer for now
		 remove the stupid check for gadget_driver otherwise
		  we don't handle IRQs ]
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

the MUSB IP is always OTG, so there's no point
in adding so many ifdefs on the code. Drop those
and always compile the driver for OTG support.

This also allows us to drop the useless "driver
mode" choice. For doing that, we need to make
musb depend on both Host and Peripheral side.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

peripheral drivers are using usb_add_gadget()/usb_del_gadget() to
register/unregister to the udc-core.

The udc-core will take the first available gadget driver and attach
function driver which is calling usb_gadget_register_driver(). This is
the same behaviour we have right now.

Only dummy_hcd was tested, the others were compiled tested.

Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Anton Tikhomirov <av.tikhomirov@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Darius Augulis <augulis.darius@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Pavankumar Kondeti <pkondeti@codeaurora.org>
Cc: Roy Huang <roy.huang@analog.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Cc: Xiaochen Shen <xiaochen.shen@intel.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Cc: Yuan-Hsin Chen <yhchen@faraday-tech.com>
Cc: cxie4 <cxie4@marvell.com>
Cc: linux-geode@lists.infradead.org
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixes mis-use of MUSB's hardware feature where it won't
flush FIFOs when TXPKTRDY flag was set before and we are
flushing setting both FLUSHFIFO and TXPKTRDY.

In other words, we need to ensure that when we try to
flush FIFOs, we don't accidentaly set TXPKTRDY bit too
due to a read-back of the register.

The MUSB Programming Guide says "May be set simultaneously
with TxPktRdy to abort the packet that is currently being
loaded into the FIFO". This is a situation where TXPKTRDY
hasn't been set yet, but some data already loaded into the
fifo. It looks, that if TXPKTRDY has been set before, and
there is no loading in progress, but we set FLUSHFIFO with
the TXPKTRDY, controller tries to use the same logic to
abort loading and as the result just does nothing (because
there is no packet been loaded currently)
Signed-off-by: NYauheni Kaliuta <yauheni.kaliuta@nokia.com>

[ balbi@ti.com : fixed one whitespace git complained about
		 improved the commit log slightly ]
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Although U8500 and U5500 platforms use paltform dma, Inventra dma specific code
can work for them for the most part. Only difference is for the Rx path where
this patch is making use of request->short_not_ok to select dma mode.
Signed-off-by: NMian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Call VBUS pulsing API when there is SRP initiation from user space.
Signed-off-by: NHema HK <hemahk@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We have a generic way of enabling/disabling
different debug messages on a driver called
DYNAMIC_PRINTK. Anyone interested in enabling
just part of the debug messages, please read
the documentation under:

Documentation/dynamic-debug-howto.txt

for information on how to use that great
infrastructure.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Commit 3dacdf11 "usb: factor out state_string() on otg drivers"
broke building musb drivers since there is already another
otg_state_string() function in musb drivers, but with different
prototype. Fix musb drivers to use common otg_state_string(), too.

Also provide a nop for otg_state_string() if CONFIG_USB_OTG_UTILS
is not defined.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If cable is not connected to peripheral only board when initializing the
gadget driver, then runtime pm calls are out-of-sync and the musb cannot
idle with omap2430.c. This was noted on Nokia N900 where musb prevented the
CPU to be able to enter deeper retention idle state.

This was working in 2.6.38 before runtime pm conversions but there musb
smart standby/idle modes were configured statically where they are now
updated runtime depending on use and cable status.

Reason for out-of-sync is that runtime pm is activated in function
musb_gadget.c: usb_gadget_probe_driver but suspended only in OTG mode if
cable is not connected when initializing. In peripheral only mode this leads
to out-of-sync runtime pm since runtime pm remain active and is activated
another time in omap2430.c: musb_otg_notifications for VBUS Connect event
and thus cannot suspend for VBUS Disconnect event since the use count remains
active.

Fix this by moving cable status check and pm_runtime_put call in
usb_gadget_probe_driver out of is_otg_enabled block.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We are now using our own list_head, so we should
be checking against that, not the gadget driver's
list_head.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

On the completion of tx dma, dma is disabled by clearing MUSB_TXCSR_DMAENAB in
TXCSR. If MUSB_TXCSR_AUTOSET was set in txstate() it will remain set although
it is not needed in PIO mode. Clear it as soon as it is not needed.
Signed-off-by: NMian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There was conflict while merging 2 patches. Enabling vbus code
is wrongly moved to error check if loop.

This is a fix to resolve the merge issue.
Signed-off-by: NHema HK <hemahk@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>