In the following functions, rename the generic 'out' goto label to the more
descriptive 'release' to indicate the type of common work that is done
before exiting the functions.  No functional change, cosmetic only.

e1000_sw_lcd_config_ich8lan()
e1000_oem_bits_config_ich8lan()
e1000_init_phy_wakeup()
e1000e_write_phy_reg_bm()
e1000e_read_phy_reg_bm()
e1000e_read_phy_reg_bm2()
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

To ease searching for debug message strings, concatenate strings that span
multiple lines even if the resulting line exceeds 80 columns; these will
not cause checkpatch warnings.

Also, add '\n' and remove unnecessary '\r' from a few debug strings.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Moves the Intel wired LAN drivers into drivers/net/ethernet/intel/ and
the necessary Kconfig and Makefile changes.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

after review of all intel drivers, found several instances where
drivers had the incorrect pattern of:
memory mapped write();
delay();

which should always be:
memory mapped write();
write flush(); /* aka memory mapped read */
delay();

explanation:
The reason for including the flush is that writes can be held
(posted) in PCI/PCIe bridges, but the read always has to complete
synchronously and therefore has to flush all pending writes to a
device.  If a write is held and followed by a delay, the delay
means nothing because the write may not have reached hardware
(maybe even not until the next read)
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Doing a PHY page select can take a long time, relatively speaking. This
can cause a significant delay when updating a number of PHY registers on
the same page by unnecessarily setting the page for each PHY access. For
example when going to Sx, all the PHY wakeup registers (WUC, RAR[], MTA[],
SHRAR[], IP4AT[], IP6AT[], etc.) on 82577/8/9 need to be updated which
takes a long time which can cause issues when suspending.

This patch introduces new PHY ops function pointers to allow callers to
set the page directly and do any number of PHY accesses on that page.
This feature is currently only implemented for 82577, 82578 and 82579
PHYs for both the normally addressed registers as well as the special-
case addressing of the PHY wakeup registers on page 800. For the latter
registers, the existing function for accessing the wakeup registers has
been divided up into three- 1) enable access to the wakeup register page,
2) perform the register access and 3) disable access to the wakeup register
page. The two functions that enable/disable access to the wakeup register
page are necessarily available to the caller so that the caller can restore
the value of the Port Control (a.k.a. Wakeup Enable) register after the
wakeup register accesses are done.

All instances of writing to multiple PHY registers on the same page are
updated to use this new method and to acquire any PHY locking mechanism
before setting the page and performing the register accesses, and release
the locking mechanism afterward.

Some affiliated magic number cleanup is done as well.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

With durations less than 20ms, the jiffies or legacy timer backed msleep()
may sleep ~20ms which might not be what the caller expects.  Instead, it
is recommended to use the hrtimers backed usleep_range().  For more, see
Documentation/timers/timers-howto.txt.  Issues reported by checkpatch.

In addition, remove unnecessary sleep in e1000e_write_nvm_spi().
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Static analysis of the driver code found some variables for which the scope
can be reduced, or remove the variable altogether.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some minor comment errors and whitespace issues discovered while looking
into this are also addressed.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Cleans up the code a bit by using the driver-specific e1e_rphy and
e1e_wphy macros instead of the full function pointer variants.  Fix
a couple whitespace issue with two already existing calls to e1e_wphy.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

WARNING: braces {} are not necessary for any arm of this statement
WARNING: braces {} are not necessary for single statement blocks
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ERROR: that open brace { should be on the previous line
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

During init, reading the 2 PHY ID registers back-to-back in the default
fast mode could return invalid data (all F's) and in slow mode could
return data to the second read the data from the first read.  To resolve
the issue in fast mode, set to slow mode before any PHY accesses; to
resolve the issue in slow mode, put in a delay for every 82579 PHY access.
Since this PHY is currently only paired with the pch2lan MAC and the PHY
type is not known before the first PHY access which can fail this way,
check for this based on MAC-type.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on work by Joe Perches <joe@perches.com>

Using static const to decrease data and overall object size.

CC: Joe Perches <joe@perches.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NEmil Tantilov <emil.s.tantilov@intel.com>

"gadget", "through", "command", "maintain", "maintain", "controller", "address",
"between", "initiali[zs]e", "instead", "function", "select", "already",
"equal", "access", "management", "hierarchy", "registration", "interest",
"relative", "memory", "offset", "already",
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The force_speed_duplex function pointer was incorrectly set.  Instead of
calling the 82577-specific version it was calling the m88 version which,
among other incorrect things, reset the PHY causing autonegotiation to be
re-enabled in the PHY resulting in the link defaulting to half-duplex.
The 82577-specific force_speed_duplex function also had an issue where
it disabled Auto-MDI-X which caused the link to not come up.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A previous 82577 workaround that set the MDIO access speed to slow mode for
every PHY register read/write when the cable is unplugged should instead
set the access mode to always be slow before any PHY register access.
Since the mode bit gets cleared when the PHY is reset, set the mode after
every PHY reset.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some function pointers for a few PHY operations (for 82578 and 82567) and
were set incorrectly causing functions to be executed that were accessing
incorrect PHY register offsets for that particular device.  This patch also
moves a few PHY-specific functions from ich8lan.c to the more appropriate
phy.c.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The workaround that detects the correct PHY ID when an initial read of the
PHY ID registers returns an invalid one should retry up to ten times with
a small delay between attempts using a single PHY address and then repeat
using the remaining possible PHY addresses.  Do this instead of trying each
possible PHY address repeating that up to 100 times.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the case for 82577 because it does not support the ability to check
for downshift.  Add case for e1000_phy_bm which can do this.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add some helpful debug messages.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The different families (80003es2lan, 8257x, ICHx/PCH) supported by the
driver each have their own conditions when the PHY can be powered down.
This patch rewrites the PHY power up/down code to fit with the family-
specific style used in the driver.  All pre-existing calls to power up or
down the PHY remain untouched.  A new call to power down the PHY when
removing the driver when the interface is down replaces the current call
to reset the PHY in order to reduce power consumption.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set booleans to 'true' or 'false' to make it clear it is a boolean.  Also
change instances of TRUE/FALSE in comments to lowercase true/false.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The phy and nvm operations structures have function pointers that contain
"phy" and "nvm" in the pointer names which are redundant since the
structures are already obviously in phy and nvm structures.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch depends on a previous one that cleans up redundant #includes.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The e1000_get_cable_length_82577() should return a negative value upon
error.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A workaround for pre-release versions of 82577 is causing link issues on
some switches.  The workaround is no longer needed on production parts so
remove it.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove unnecessary workaround that mistakenly does not perform a page
select operation for PHY registers 29 and 30 (assuming these are the PHY
debug port address and data registers) on 82578 which can cause reads
of the Transmit with No Carrier Sense statistics register on page 778 to be
read from an incorrect page.  Also error out if the page select operation
fails.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch reworks a previous workaround (commit 7d3cabbc) for an issue
in hardware where noise on the interconnect between the MAC and PHY could
be generated by a lower power mode (K1) at 1000Mbps resulting in bad
packets.  Disable K1 while at 1000 Mbps but keep it enabled for 10/100Mbps
and when the cable is disconnected.  The original version of this
workaround was found to be incomplete.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PCH-based parts (82577/82578) and some ICH8-based parts (82566) need to
hold the swflag (sw/fw/hw hardware semaphore) over consecutive PHY accesses
in order to perform sw-driven PHY configuration during initialization to
workaround known hardware issues (see follow-on patch).  This patch
provides new PHY read/write functions (and function pointers) that will
allow accessing the PHY registers assuming the swflag has already been
acquired.  The actual PHY register access code has moved into helper
functions that are called with a flag indicating whether or not the swflag
has already been acquired and acquires/releases it if not.

The functions called from within the updated PHY access functions had to be
updated to assume the swflag was already acquired, and other functions that
called those functions were also updated to acquire/release the swflag.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some PHYs may require two reads of the PHY_STATUS register to determine the
link status.  If the PHY is being accessed by another thread it is possible
the first read could timeout and fail.  In this case, put a delay in so
the second read will pick up the correct link status.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PHY loopback on 82578 fails to work as a result of flushing the packets
in the FIFO buffer in the link stall workaround.  Don't perform the
workaround if in PHY loopback mode.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>