The drm core _really_ likes to frob around with the crtc timings and
put halfed vertical timings (in fields) in there. Which confuses the
overlay code, resulting in it's refusal to display anything at the
lower half of an interlaced pipe.
Tested-by: NChristopher Egert <cme3000@gmail.com>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NPeter Ross <pross@xvid.org>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NChristopher Egert <cme3000@gmail.com>
Tested-by: NAlfonso Fiore <alfonso.fiore@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NPeter Ross <pross@xvid.org>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NChristopher Egert <cme3000@gmail.com>
Tested-by: NAlfonso Fiore <alfonso.fiore@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The hw seems to use this to correctly insert the required delay
before/after an even/odd interlaced field. This might also explain
why we need to substract 1 half-line from vtotal - if the hw just
adds the delay programmend in VSYNCSHIFT the total frame time would be
about that too long.

These registers seems to only exist on gen4 and later. For paranoia
also program it to 0 for progressive modes, but according to
documentation the hw should just ignore it in this case.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NAlfonso Fiore <alfonso.fiore@gmail.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

gen2 doesn't support it, so be a bit more paranoid and add a check to
ensure that we never ever set an unsupported interlaced bit.

Ensure that userspace can't set an interlaced mode by resetting
interlace_allowed for the crt on gen2. dvo and lvds are the only other
encoders that gen2 supports and these already disallow interlaced
modes.
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

According to Paulo Zanoni, this is what windows does.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NAlfonso Fiore <alfonso.fiore@gmail.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

According to bspec, we need to subtract an additional line from vtotal
for interlaced modes and vblank_end needs to equal vtotal. All other
timing fields do not need this special treatment, so kill it.

Bspec says that this is irrespective of whether the interlaced mode
has an odd or even vtotal, both modes are supported.
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NChristopher Egert <cme3000@gmail.com>
Tested-by: NAlfonso Fiore <alfonso.fiore@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We have a pretty decent confusion about vertical timings of interlaced
modes. Peter Ross has written a patch that makes interlace modes work
on a lot more platforms/output combinations by doubling the vertical
timings.

The issue with that patch is that core drm _does_ support specifying
whether we want these vertical timings in fields or frames, we just
haven't managed to consistently use this facility. The relavant
function is drm_mode_set_crtcinfo, which fills in the crtc timing
information.

The first thing to note is that the drm core keeps interlaced modes in
frames, but displays modelines in fields. So when the crtc modeset
helper copies over the mode into adjusted_mode it will already contain
vertical timings in half-frames. The result is that the fixup code in
intel_crtc_mode_fixup doesn't actually do anything (in most cases at
least).

Now gen3+ natively supports interlaced modes and wants the vertical
timings in frames. Which is what sdvo already fixes up, at least under
some conditions.

There are a few other place that demand vertical timings in fields
but never actually deal with interlaced modes, so use frame timings
for consistency, too. These are:
- lvds panel,
- dvo encoders - dvo is the only way gen2 could support interlaced
  mode, but currently we don't support any encoders that do.
- tv out - despite that the tv dac sends out an interlaced signal it
  expects a progressive mode pipe configuration.
All these encoders enforce progressive modes by resetting
interlace_allowed.

Hence we always want crtc vertical timings in frames. Enforce this in
our crtc mode_fixup function and rip out any redudant timing
computations from the encoders' mode_fixup function.

v2-4: Adjust the vertical timings a bit.

v5: Split out the 'subtract-one for interlaced' fixes.

v6: Clarify issues around tv-out and gen2.
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NChristopher Egert <cme3000@gmail.com>
Tested-by: NAlfonso Fiore <alfonso.fiore@gmail.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

- Clarify which bits are for which chips.
- Note that gen2 can't do interlaced directly (only via dvo tv chips).
- Move the mask to the top to make it clearer how wide this field is.
- Add defintions for all possible values.

This patch doesn't change any code.

v2: Paulo Zanoni pointed out that the pixel doubling modes do no
longer exist on ivb.

Cc: Peter Ross <pross@xvid.org>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NChristopher Egert <cme3000@gmail.com>
Tested-by: NAlfonso Fiore <alfonso.fiore@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Back-merge from drm-fixes into drm-intel-next to sort out two things:

- interlaced support: -fixes contains a bugfix to correctly clear
  interlaced configuration bits in case the bios sets up an interlaced
  mode and we want to set up the progressive mode (current kernels
  don't support interlaced). The actual feature work to support
  interlaced depends upon (and conflicts with) this bugfix.

- forcewake voodoo to workaround missed IRQ issues: -fixes only enabled
  this for ivybridge, but some recent bug reports indicate that we
  need this on Sandybridge, too. But in a slightly different flavour
  and with other fixes and reworks on top. Additionally there are some
  forcewake cleanup patches heading to -next that would conflict with
  currrent -fixes.
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Merge branch 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux into drm-fixes

* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux:
  drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT (v2)
  drm/i915: no lvds quirk for AOpen MP45
  drm/i915: Force explicit bpp selection for intel_dp_link_required
  drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT
  drm/i915:: Disable FBC on SandyBridge

We want to unconditionally enable ppgtt for two reasons:
- Windows uses this on snb and later.
- We need the basic hw support to work before we can think about real
  per-process address spaces and other cool features we want.

But Chris Wilson was complaining all over irc and intel-gfx that this
will blow up if we don't have a module option to disable it. Hence add
one, to prevent this.

ppgtt support seems to slightly change the timings and make crashy
things slightly more or less crashy. Now in my testing and the testing
this got on troublesome snb machines, it seems to have improved things
only. But on ivb it makes quite a few crashes happen much more often,
see

https://bugs.freedesktop.org/show_bug.cgi?id=41353

Luckily Eugeni Dodonov seems to have a set of workarounds that fix
this issue.

v2: Don't try to enable ppgtt on pre-snb.

v3: Pimp commit message and make Chris Wilson less grumpy by adding a
module option.

v4: New try at making Chris Wilson happy.
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Tested-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This was pretty usefull for debugging, might be useful for diagnosing
issues.
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Tested-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Split out for easier cross-checking of the boring pieces with bspec.
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Tested-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This adds support to bind/unbind objects and wires it up. Objects are
only put into the ppgtt when necessary, i.e. at execbuf time.

Objects are still unconditionally put into the global gtt.

v2: Kill the quick hack and explicitly pass cache_level to ppgtt_bind
like for the global gtt function. Noticed by Chris Wilson.
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Tested-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This just adds the setup and teardown code for the ppgtt PDE and the
last-level pagetables, which are fixed for the entire lifetime, at
least for the moment.

v2: Kill the stray debug printk noted by and improve the pte
definitions as suggested by Chris Wilson.

v3: Clean up the aperture stealing code as noted by Ben Widawsky.

v4: Paint the init code in a more pleasing colour as suggest by Chris
Wilson.

v5: Explain the magic numbers noticed by Ben Widawsky.
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Tested-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need this because ppgtt page directory entries need to be in the
global gtt pagetable.
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Tested-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

To implement a PPGTT for drm/i915 that fully aliases the GTT, we also
need to properly alias the scratch page.
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Tested-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Chris Wilson and me have again stared at funny error states and it's
been pretty clear from the start that something was seriously amiss.
The seqnos last seen by the cpu were a few hundred behind those that
the gpu could have possibly emitted last before it died ...

Chris now tracked it down (hopefully, definit verdict's still out),
but in hindsight we'd have found the bug by simply dumping the cpu
side tracking of the ring head and tail registers.

Fix this and prevent an identical time-waster in the future.

Because the hangs always involved semaphores in one way or another,
we've tried to dump the mbox registers, but couldn't find any
inconsistencies. Still, dump them too.
Reviewed-and-wanted-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

These are all user-trigerable, so tune down their loudness a notch.
For some of these we have i-g-t tests (because they prevent
newly-discovered bugs), without this patches running the test suite
leaves behind a dirty dmesg.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On gen5 we also need to correctly set up swizzling in the display
scanout engine, but only there. Consolidate this into the same
function.

This has a small effect on ums setups - the kernel now also sets this
bit in addition to userspace setting it. Given that this code only
runs when userspace either can't (resume, gpu reset) or explicitly
won't(gem_init) touch the hw this shouldn't have an adverse effect.
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We have to do this manually. Somebody had a Great Idea.

I've measured speed-ups just a few percent above the noise level
(below 5% for the best case), but no slowdows. Chris Wilson measured
quite a bit more (10-20% above the usual snb variance) on a more
recent and better tuned version of sna, but also recorded a few
slow-downs on benchmarks know for uglier amounts of snb-induced
variance.

v2: Incorporate Ben Widawsky's preliminary review comments and
elaborate a bit about the performance impact in the changelog.

v3: Add a comment as to why we don't need to check the 3rd memory
channel.

v4: Fixup whitespace.
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NEric Anholt <eric@anholt.net>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

An identical patch has been merged for i9xx_crtc_mode_set:

Commit 59df7b17
Author: Christian Schmidt <schmidt@digadd.de>
Date:   Mon Dec 19 20:03:33 2011 +0100

    drm/intel: Fix initialization if startup happens in interlaced mode [v2]

But that one neglected to fix up the ironlake+ path.

This should fix the issue reported by Alfonso Fiore where booting with
only a HDMI cable connected to his TV failed to display anything. The
issue is that the bios set up things for 1080i and used the pannel
fitter to scale up the lower progressive resolutions. We failed to
clear the interlace bit in the PIPEACONF register, resulting in havoc.

v2: Be more paranoid and just unconditionally clear the field before
setting new values.

Cc: Peter Ross <pross@xvid.org>
Cc: Alfonso Fiore <alfonso.fiore@gmail.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NKeith Packard <keithp@keithp.com>

According to a bug report, it doesn't have one.

Cc: stable@kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44263Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NKeith Packard <keithp@keithp.com>

It is never correct to use intel_crtc->bpp in intel_dp_link_required,
so instead pass an explicit bpp in to this function. This patch
only supports 18bpp and 24bpp modes, which means that 10bpc modes will
be computed incorrectly. Fixing that will require more extensive
changes, and so must be addressed separately from this bugfix.

intel_dp_link_required is called from intel_dp_mode_valid and
intel_dp_mode_fixup.

* intel_dp_mode_valid is called to list supported modes; in this case,
  the current crtc values cannot be relevant as the modes in question
  may never be selected. Thus, using intel_crtc->bpp is never right.

* intel_dp_mode_fixup is called during mode setting, but it is run
  well before ironlake_crtc_mode_set is called to set intel_crtc->bpp,
  so using intel_crtc-bpp in this path can only ever get a stale
  value.

Cc: Lubos Kolouch <lubos.kolouch@gmail.com>
Cc: Adam Jackson <ajax@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=42263
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44881Tested-by: NDave Airlie <airlied@redhat.com>
Tested-by: camalot@picnicpark.org (Dell Latitude 6510)
Tested-by: NRoland Dreier <roland@digitalvampire.org>
Signed-off-by: NKeith Packard <keithp@keithp.com>

This return statement got dropped while fixing the conflicts introduced
in 7a7e8734.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The c32 structure is allocated on the stack and its idx field is not
initialized before copying it to user level.  This patch takes the value
from the result of the ioctl, as done for the other fields.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDave Airlie <airlied@redhat.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  rbd: fix safety of rbd_put_client()
  rbd: fix a memory leak in rbd_get_client()
  ceph: create a new session lock to avoid lock inversion
  ceph: fix length validation in parse_reply_info()
  ceph: initialize client debugfs outside of monc->mutex
  ceph: change "ceph.layout" xattr to be "ceph.file.layout"

Signed-off-by: NJosh Triplett <josh@joshtriplett.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The rbd_client structure uses a kref to arrange for cleaning up and
freeing an instance when its last reference is dropped.  The cleanup
routine is rbd_client_release(), and one of the things it does is
delete the rbd_client from rbd_client_list.  It acquires node_lock
to do so, but the way it is done is still not safe.

The problem is that when attempting to reuse an existing rbd_client,
the structure found might already be in the process of getting
destroyed and cleaned up.

Here's the scenario, with "CLIENT" representing an existing
rbd_client that's involved in the race:

 Thread on CPU A                | Thread on CPU B
 ---------------                | ---------------
 rbd_put_client(CLIENT)         | rbd_get_client()
   kref_put()                   |   (acquires node_lock)
     kref->refcount becomes 0   |   __rbd_client_find() returns CLIENT
     calls rbd_client_release() |   kref_get(&CLIENT->kref);
                                |   (releases node_lock)
       (acquires node_lock)     |
       deletes CLIENT from list | ...and starts using CLIENT...
       (releases node_lock)     |
       and frees CLIENT         | <-- but CLIENT gets freed here

Fix this by having rbd_put_client() acquire node_lock.  The result
could still be improved, but at least it avoids this problem.
Signed-off-by: NAlex Elder <elder@dreamhost.com>
Signed-off-by: NSage Weil <sage@newdream.net>

This fixes the race in process_vm_core found by Oleg (see

  http://article.gmane.org/gmane.linux.kernel/1235667/

for details).

This has been updated since I last sent it as the creation of the new
mm_access() function did almost exactly the same thing as parts of the
previous version of this patch did.

In order to use mm_access() even when /proc isn't enabled, we move it to
kernel/fork.c where other related process mm access functions already
are.
Signed-off-by: NChris Yeoh <yeohc@au1.ibm.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If an existing rbd client is found to be suitable for use in
rbd_get_client(), the rbd_options structure is not being
freed as it should.  Fix that.
Signed-off-by: NAlex Elder <elder@dreamhost.com>
Signed-off-by: NSage Weil <sage@newdream.net>

Lockdep was reporting a possible circular lock dependency in
dentry_lease_is_valid().  That function needs to sample the
session's s_cap_gen and and s_cap_ttl fields coherently, but needs
to do so while holding a dentry lock.  The s_cap_lock field was
being used to protect the two fields, but that can't be taken while
holding a lock on a dentry within the session.

In most cases, the s_cap_gen and s_cap_ttl fields only get operated
on separately.  But in three cases they need to be updated together.
Implement a new lock to protect the spots updating both fields
atomically is required.
Signed-off-by: NAlex Elder <elder@dreamhost.com>
Reviewed-by: NSage Weil <sage@newdream.net>

"len" is read from network and thus needs validation.  Otherwise, given
a bogus "len" value, p+len could be an out-of-bounds pointer, which is
used in further parsing.
Signed-off-by: NXi Wang <xi.wang@gmail.com>
Signed-off-by: NSage Weil <sage@newdream.net>

Initializing debufs under monc->mutex introduces a lock dependency for
sb->s_type->i_mutex_key, which (combined with several other dependencies)
leads to an annoying lockdep warning.  There's no particular reason to do
the debugfs setup under this lock, so move it out.

It used to be the case that our first monmap could come from the OSD; that
is no longer the case with recent servers, so we will reliably set up the
client entry during the initial authentication.

We don't have to worry about racing with debugfs teardown by
ceph_debugfs_client_cleanup() because ceph_destroy_client() calls
ceph_msgr_flush() first, which will wait for the message dispatch work
to complete (and the debugfs init to complete).

Fixes: #1940
Signed-off-by: NSage Weil <sage@newdream.net>

The virtual extended attribute named "ceph.layout" is meaningful
only for regular files.  Change its name to be "ceph.file.layout" to
more directly reflect that in the ceph xattr namespace.  Preserve
the old "ceph.layout" name for the time being (until we decide it's
safe to get rid of it entirely).

Add a missing initializer for "readonly" in the terminating entry.
Signed-off-by: NAlex Elder <elder@dreamhost.com>
Reviewed-by: NSage Weil <sage@newdream.net>

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon/kms/blit: fix blit copy for very large buffers
  drm/radeon/kms: fix TRAVIS panel setup
  drm/radeon: fix use after free in ATRM bios reading code.
  drm/radeon/kms: Fix device tree linkage of DP i2c buses too
  drm/radeon: Set DESKTOP_HEIGHT register to the framebuffer (not mode) height.
  drm/radeon/kms: disable output polling when suspended
  drm/nv50/pm: signedness bug in nv50_pm_clocks_pre()
  drm/nouveau/gem: fix fence_sync race / oops
  drm/nouveau: fix typo on mxmdcb option
  drm/nouveau/mxm: pretend to succeed, even if we can't shadow the MXM-SIS
  drm/nouveau/disp: check that panel power gpio is enabled at init time

* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
  Revert "microblaze: Add topology init"

Merge branches 'core-urgent-for-linus', 'perf-urgent-for-linus', 'sched-urgent-for-linus' and 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  bugs, x86: Fix printk levels for panic, softlockups and stack dumps

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf top: Fix number of samples displayed
  perf tools: Fix strlen() bug in perf_event__synthesize_event_type()
  perf tools: Fix broken build by defining _GNU_SOURCE in Makefile
  x86/dumpstack: Remove unneeded check in dump_trace()
  perf: Fix broken interrupt rate throttling

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/rt: Fix task stack corruption under __ARCH_WANT_INTERRUPTS_ON_CTXSW
  sched: Fix ancient race in do_exit()
  sched/nohz: Fix nohz cpu idle load balancing state with cpu hotplug
  sched/s390: Fix compile error in sched/core.c
  sched: Fix rq->nr_uninterruptible update race

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/reboot: Remove VersaLogic Menlow reboot quirk
  x86/reboot: Skip DMI checks if reboot set by user
  x86: Properly parenthesize cmpxchg() macro arguments