iw dev <devname> station del <MAC address> is quiet useful in mesh mode and should be possible.
Signed-off-by: NMarco Porsch <marco.porsch@siemens.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Mac80211 drivers can now pass paged SKBs to mac80211 via
ieee80211_rx{_irqsafe}. The implementation currently use
skb_linearize() in a few places i.e. management frame
handling, software decryption, defragmentation and A-MSDU
process. We will optimize them one by one later.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Cc: Kalle Valo <kalle.valo@iki.fi>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also correct indentation in net/wireless/reg.c.
Signed-off-by: NFrans Pop <elendil@planet.nl>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for basic configuration of a connection quality monitoring to the
nl80211 interface, and basic support for notifying about triggered monitoring
events.

Via this interface a user-space connection manager may configure and receive
pre-warning events of deteriorating WLAN connection quality, and start
preparing for roaming in advance, before the connection is already lost.

An example usage of such a trigger is starting scanning for nearby AP's in
an attempt to find one with better connection quality, and associate to it
before the connection characteristics of the existing connection become too bad
or the association is even lost, leading in a prolonged delay in connectivity.

The interface currently supports only RSSI, but it could be later extended
to include other parameters, such as signal-to-noise ratio, if need for that
arises.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's a wireless.h macro for this, might as well use it.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's a wireless.h macro for this, might as well use it.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The most needed command from nl80211, which Wireless Extensions had,
is support for power save mode. Add a simple command to make it possible
to enable and disable power save via nl80211.

I was also planning about extending the interface, for example adding the
timeout value, but after thinking more about this I decided not to do it.
Basically there were three reasons:

Firstly, the parameters for power save are very much hardware dependent.
Trying to find a unified interface which would work with all hardware, and
still make sense to users, will be very difficult.

Secondly, IEEE 802.11 power save implementation in Linux is still in state
of flux. We have a long way to still to go and there is no way to predict
what kind of implementation we will have after few years. And because we
need to support nl80211 interface a long time, practically forever, adding
now parameters to nl80211 might create maintenance problems later on.

Third issue are the users. Power save parameters are mostly used for
debugging, so debugfs is better, more flexible, interface for this.
For example, wpa_supplicant currently doesn't configure anything related
to power save mode. It's better to strive that kernel can automatically
optimise the power save parameters, like with help of pm qos network
and other traffic parameters.

Later on, when we have better understanding of power save, we can extend
this command with more features, if there's a need for that.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make remaining netlink policies as const.
Fixup coding style where needed.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This implements a new command to register for action frames
that userspace wants to handle instead of the in-kernel
rejection. It is then responsible for rejecting ones that
it decided not to handle. There is no unregistration, but
the socket can be closed for that.

Frames that are not registered for will not be forwarded
to userspace and will be rejected by the kernel, the
cfg80211 API helps implementing that.

Additionally, this patch adds a new command that allows
doing action frame transmission from userspace. It can be
used either to exchange action frames on the current
operational channel (e.g., with the AP with which we are
currently associated) or to exchange off-channel Public
Action frames with the remain-on-channel command.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As discussed in linux-wireless mailing list, adding and removing
stations for mesh topologies is not necessary. Since doing it triggers
bugs, the sugestion was to simply disable it.

Tested using a custom iw command "station new". Works only after using
hostapd. "station del" command also works.
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Simon Raffeiner <sturmflut@lieberbiber.de>
Cc: Andrey Yurovsky <andrey@cozybit.com>
Cc: Javier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Upstream radiotap has adopted the namespace
proposal David Young made and I then took care
of, for which I had adapted the radiotap parser
as a library outside the kernel. This brings
the in-kernel parser up to speed.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Introduce TKIP_HDR_LEN define for code clarity (in the same way as
CCMP_HDR_LEN).

Also odd len variable (not used) dropped from lib80211_tkip_hdr().
Signed-off-by: NAndriy V. Tkachuk <andrit@ukr.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NAndriy V. Tkachuk <andrit@ukr.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds a new regulatory hint to be used when we know all
devices have been disconnected and idle. This can happen
when we suspend, for instance. When we disconnect we can
no longer assume the same regulatory rules learned from
a country IE or beacon hints are applicable so restore
regulatory settings to an initial state.

Since driver hints are cached on the wiphy that called
the hint, those hints are not reproduced onto cfg80211
as the wiphy will respect its own wiphy->regd regardless.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When cfg80211 starts it will send a core regulatory hint. This is
sent to the global workqueue but we force processing of it by
flushing the global workqueue. The flushing was done since
cfg80211 needs last_request to always be populated.

Avoid flushing the global workqueue by processing the work
required immediately instead of putting it into a linked
list and processing it after the flush.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This new function (previously a static function
called just "find_ie" can be used to find a
specific IE in a buffer of IEs.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ieee80211_hdrlen() should account account new HT Control field in 802.11
data frame header introduced by IEEE 802.11n standard.

According to 802.11n-2009 HT Control field is present in data frames
when both of following are met:

   1. It is QoS data frame.
   2. Order bit is set in Frame Control field.

The change might be totally compatible with legacy non-11n aware frames,
because 802.11-2007 standard states that "all QoS STAs set this subfield
to 0".
Signed-off-by: NAndriy V. Tkachuk <andrit@ukr.net>
Acked-by : Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If a device has multiple MAC addresses, userspace will
need to know about that. Similarly, if it allows the
MAC addresses to vary by a bitmask.

If a driver exports multiple addresses, it is assumed
that it will be able to deal with that many different
addresses, which need not necessarily match the ones
programmed into the device; if a mask is set then the
device should deal addresses within that mask based
on an arbitrary "base address".

To test it all and show how it is used, add support
to hwsim even though it can't actually deal with
addresses different from the default.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

nl80211_associate() was rejecting (re)association attempts with EBUSY
in some cases where we are currently associated with an AP that uses
different channel from the destination AP. Fix this by passing the
current wdev to rdev_fixed_channel() in the same way that was already
done for join-IBSS and connect commands. This allows the fixedchan
check to skipped for the current wdev and allows the reassociation to
proceed.
Signed-off-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Future code will need to look up rdev and wdev
within atomic sections, but currently we need
to lock a mutex for such lookups. Change the
list handling for both to be RCU-safe so that
we can look them up in rcu sections instead in
the future.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

__net_init/__net_exit are apparently not going away, so use them
to full extent.

In some cases __net_init was removed, because it was called from
__net_exit code.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In practice APs do not send country IE channel triplets for channels
the AP is not operating on and if they were to do so they would have
to use the regulatory extension which we currently do not process.
No AP has been seen in practice that does this though so just drop
those country IEs.

Additionally it has been noted the first series of country IE
channels triplets are specific to the band the AP sends. Propagate
the band on which the country IE was found on reject the country
IE then if the triplets are ever oustide of the band.

Although we now won't process country IE information with multiple
band information we leave the intersection work as is as it is
technically possible for someone to want to eventually process these
type of country IEs with regulatory extensions.

Cc: Jouni Malinen <jouni.malinen@atheros.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Previous to this and the last patch, titled,

"cfg80211: Fix 2 GHz subband calculation for country IEs"

we would end up treating these IEs as single channel units. These are in
fact just bogus IE triplets so ignore the entire IE if these are found.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Country IEs triplets are getting an extra channel with
the current count. This does not affect regulatory because
we always took the intersection between what the AP gave
and what CRDA believed is correct.

This however does fix processing some Country IEs with multiple
sequential 2 GHz triplets. Since our parser and the spec mandates
all channels be monitonically increasing we would drop the IE after
noticing the second triplet begins on a channel already processed.
APs that send these type of country IEs seems rare though.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Patch fixes the bug at
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2139

Currently we cannot set the channel using wext extension
if we have already associated and disconnected. As
cfg80211_mgd_wext_siwfreq will not switch the channel if ssid is set.
This fixes it by clearing the ssid.
Following is the sequence which it tries to fix.
modprobe iwlagn
iwconfig wlan0 essid ""
ifconfig wlan0 down
iwconfig wlan0 chan X

wext is marked as deprecate.If we use nl80211 we can easily play with
setting the channel.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This enhances the way we parse country IEs to minimize
the number of regulatory rules that we create. It also fixes
our current implementation which treated country IE triplets
with only one channel as one independed regulatory rule even
though adjecent rules were also being provided.

Without this patch APs which send country IE information with
a channel triplet for each individual channel will force cfg80211
to deny HT40 operation as a regulatory rule would have been created
independently for each channel and as such configured only for
20 MHz operation.

Although 802.11n APs which send country IEs triplets in this fassion
are likely rare Benoit reports this against the Ubiquity NanoStation M5,
with Country "FR" and HT40 enabled.

Since we now have a helper which parses the triplets in intermediate
steps we now take care extra care to process padding.
Reported-by: NBenoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The max power from each country IE triplet was being ignored.
This fix isn't critical as CRDA was always being used for the lower
limit, but we should process it in case the AP still wants to
decrease power output even more for whatever reason.
Reported-by: NBenoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Store information elements from Beacon and Probe Response frames in
separate buffers to allow both sets to be made available through
nl80211. This allows user space applications to get access to IEs from
Beacon frames even if we have received Probe Response frames from the
BSS. Previously, the IEs from Probe Response frames would have
overridden the IEs from Beacon frames.

This feature is of somewhat limited use since most protocols include
the same (or extended) information in Probe Response frames. However,
there are couple of exceptions where the IEs from Beacon frames could
be of some use: TIM IE is only included in Beacon frames (and it would
be needed to figure out the DTIM period used in the BSS) and at least
some implementations of Wireless Provisioning Services seem to include
the full IE only in Beacon frames).

The new BSS attribute for scan results is added to allow both the IE
sets to be delivered. This is done in a way that maintains the
previously used behavior for applications that are not aware of the
new NL80211_BSS_BEACON_IES attribute.
Signed-off-by: NJouni Malinen <j@w1.fi>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a new NL80211_CMD_SET_TX_BITRATE_MASK command and related
attributes to provide support for setting TX rate mask for rate
control. This uses the existing cfg80211 set_bitrate_mask operation
that was previously used only with WEXT compat code (SIOCSIWRATE). The
nl80211 command allows more generic configuration of allowed rates as
a mask instead of fixed/max rate.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Extend struct cfg80211_bitrate_mask to actually use a bitfield mask
instead of just a single fixed or maximum rate index. This change
itself does not modify the behavior (except for debugfs files), but it
prepares cfg80211 and mac80211 for a new nl80211 command for setting
which rates can be used in TX rate control.

Since frames are now going through the rate control algorithm
unconditionally, the internal IEEE80211_TX_INTFL_RCALGO flag can now
be removed. The RC implementations can use the rate_idx_mask value to
optimize their behavior if only a single rate is enabled.

The old max_rate_idx in struct ieee80211_tx_rate_control is maintained
(but commented as deprecated) for backwards compatibility with existing
RC implementations. Once these implementations have been updated to
use the more generic rate_idx_mask, the max_rate_idx value can be
removed.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The new attribute NL80211_ATTR_WIPHY_COVERAGE_CLASS sets IEEE 802.11
Coverage Class, which depends on maximum distance of nodes in a
wireless network. It's required for long distance links (more than a few
hundred meters).

The attribute is now ignored by two non-mac80211 drivers, rndis and
iwmc3200wifi, together with WIPHY_PARAM_RETRY_SHORT and
WIPHY_PARAM_RETRY_LONG. If it turns out to be a problem, we could split
set_wiphy_params callback or add new capability bits.
Signed-off-by: NLukas Turek <8an@praha12.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When CONFIG_CFG80211_WEXT is not set, there is
a refcount imbalance with rdev->opencount, fix
that by moving it out of the ifdef.
Reported-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Bad macro definition in "cfg80211: add a regulatory debug print"...
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of sprinkling code with ifdef's define REG_DBG_PRINT() instead.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes a syntax error when setting up the user regulatory
hint. This change yields the same exact binary object though
so it ends up just being a syntax typo fix, fortunately.

Cc: stable@kernel.org
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When, for instance, a new IBSS peer is found, userspace
wants to be notified. Add events for all new stations
that mac80211 learns about.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add new commands for requesting the driver to remain awake
on a specified channel for the specified amount of time
(and another command to cancel such an operation). This
can be used to implement userspace-controlled off-channel
operations, like Public Action frame exchange on another
channel than the operation channel.

The off-channel operation should behave similarly to scan,
i.e. the local station (if associated) moves into power
save mode to request the AP to buffer frames for it and
then moves to the other channel to allow the off-channel
operation to be completed. The duration parameter can be
used to request enough time to receive a response from
the target station.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is no longer needed with the availability of
CONFIG_CFG80211_INTERNAL_REGDB.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>