Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 25 5月, 2011 10 次提交
  3. 16 3月, 2011 3 次提交
  5. 23 10月, 2010 3 次提交
  7. 12 8月, 2010 1 次提交
    • A
      mmc: add erase, secure erase, trim and secure trim operations · dfe86cba
      由 Adrian Hunter 提交于 
      SD/MMC cards tend to support an erase operation.  In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.

SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.

"erase_size" is the minimum size, in bytes, of an erase operation.  For
MMC, "erase_size" is the erase group size reported by the card.  Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector.  For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.

SD/MMC cards can erase an arbitrarily large area up to and
including the whole card.  When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:

    1. A single erase command will make all other I/O on the card
       wait.  This is not a problem if the whole card is being erased, but
       erasing one partition will make I/O for another partition on the
       same card wait for the duration of the erase - which could be a
       several minutes.

    2. To be able to inform the user of erase progress.

    3. The erase timeout becomes too large to be very useful.
       Because the erase timeout contains a margin which is multiplied by
       the size of the erase area, the value can end up being several
       minutes for large areas.

"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.

For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.

For SD, "preferred_erase_size" is the allocation unit size specified by
the card.

"preferred_erase_size" is in bytes.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Acked-by: NJens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      dfe86cba
  9. 11 8月, 2010 3 次提交
  11. 07 3月, 2010 1 次提交
  13. 23 9月, 2009 3 次提交
  15. 09 11月, 2008 1 次提交
  17. 27 7月, 2008 1 次提交
    • H
      mmc: Add per-card debugfs support · f4b7f927
      由 Haavard Skinnemoen 提交于 
      For each card successfully added to the bus, create a subdirectory under
the host's debugfs root with information about the card.

At the moment, only a single file is added to the card directory for
all cards: "state". It reflects the "state" field in struct mmc_card,
indicating whether the card is present, readonly, etc.

For MMC and SD cards (not SDIO), another file is added: "status".
Reading this file will ask the card about its current status and
return it. This can be useful if the card just refuses to respond to
any commands, which might indicate that the card state is not what the
MMC core thinks it is (due to a missing stop command, for example.)
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
      f4b7f927
  19. 24 9月, 2007 5 次提交
  21. 01 5月, 2007 5 次提交
  23. 05 2月, 2007 1 次提交
    • P
      mmc: Add support for SDHC cards · fba68bd2
      由 Philip Langdale 提交于 
      Thanks to the generous donation of an SDHC card by John Gilmore, and
the surprisingly enlightened decision by the SD Card Association to
publish useful specs, I've been able to bash out support for SDHC. The
changes are not too profound:

i) Add a card flag indicating the card uses block level addressing and
check it in the block driver. As we never took advantage of byte-level
addressing, this simply involves skipping the block -> byte
translation when sending commands.

ii) The layout of the CSD is changed - a set of fields are discarded
to make space for a larger C_SIZE. We did not reference any of the
discarded fields except those related to the C_SIZE.

iii) Read and write timeouts are fixed values and not calculated from
CSD values.

iv) Before invoking SEND_APP_OP_COND, we must invoke the new
SEND_IF_COND to inform the card we support SDHC.
Signed-off-by: NPhilipl Langdale <philipl@overt.org>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
      fba68bd2
  25. 02 12月, 2006 2 次提交
    • P
      mmc: Support for high speed SD cards · 7ccd266e
      由 Pierre Ossman 提交于 
      Modern SD cards support a clock speed of 50 MHz. Make sure we test for
this capability and do the song and dance required to activate it.

Activating high speed support actually modifies the TRAN_SPEED field
of the CSD. But as the spec says that the cards must report 50 MHz,
we might as well skip re-reading the CSD.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
      7ccd266e
    • P
      [PATCH] mmc: Add support for mmc v4 high speed mode · bce40a36
      由 Philip Langdale 提交于 
      This adds support for the high-speed modes defined by mmc v4
(assuming the host controller is up to it). On a TI sdhci controller,
it improves read speed from 1.3MBps to 2.3MBps. The TI controller can
only go up to 24MHz, but everything helps. Another person has taken
this basic patch and used it on a Nokia 770 to get a bigger boost
because that controller can run at 48MHZ.
Signed-off-by: NPhilip Langdale <philipl@overt.org>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
      bce40a36
  27. 03 5月, 2006 1 次提交