This is enabled only for ar9285.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make read/only data structures const. Compile tested only.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make the startup and other data parameters that are read/only
const. Compile tested only.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In uCode, BT state machine need to receive open envlope
command before perform calibration; followed by close envlope
command to move to next stage.

Since Linux has two separated uCode, one for init and the second
one for runtime; we use open envlope commands for init uCode to
indicate we are ready to perform calibration operation.
But for runtime uCode, we are not doing any init calibration,
so we issue open/close envlope commands to force uCode move to
"BT COEX ON" state.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

rt2x00usb_watchdog_reset_tx performs the same task
as rt2x00usb_kill_tx_queue, with the only difference
is that it waits for all entries to be returned to
the driver and for all frames the status has been
reported to mac80211.

We can easily split this task by calling rt2x00usb_kill_tx_queue,
sleep for a short period and invoke the TX status reporting
function. By adding the sleep() to the kill_entry we make sure
that even during shutdown we guarentee the entry has been killed when
the function returns. To make this work correctly the interrupt
handlers have to be updated to prevent checking for the RADIO_ENABLED
flag too early which prevents the ownership of the entry to be reset.
Additionally a check for the DEVICE_PRESENT flag is not required but
is nice to prevent race conditions when the device was unplugged.

Additionally rather then calling rt2x00usb_work_txdone() for
status reporting we let the driver perform the TX status reporting
first. If this is not sufficient then rt2x00usb_work_txdone() will
still be used to cleanup the mess.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The watchdog for rt2800usb triggers frequently causing all URB's
to be canceled often enough to interrupt the normal TX flow.
More research indicated that not the URB upload to the USB host
were hanging, but instead the TX status reports.

To correctly detect what is going on, we introduce Q_INDEX_DMA_DONE
which is an index counter between Q_INDEX_DONE and Q_INDEX and indicates
if the frame has been transfered to the device.

This also requires the rt2x00queue timeout functions to be updated
to differentiate between a DMA timeout (time between Q_INDEX and
Q_INDEX_DMA_DONE timeout) and a STATUS timeout (time between
Q_INDEX_DMA_DONE and Q_INDEX_DONE timeout)

All Q_INDEX_DMA_DONE code was taken from the RFC from
Helmut Schaa <helmut.schaa@googlemail.com> for the implementation
for watchdog for rt2800pci.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

USB devices upload their beacon and then automatically send
it out every beacon interval. However when killing a TX queue
we only kill the URB and not the actual transmission of the beacon.

This will reset the Beacon register to prevent any beacons from
being transmitted.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add PWR_PIN_CFG initialization for rt2800usb at the same point
as rt2800pci.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When configuring the MAC_ADDR or MAC_BSSID with an empty address,
the UNICAST_TO_ME_MASK and BSS_ID_MASK must also be reset to prevent
invalid interpretation of the addresses.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

According to the legacy drivers the AUTOWAKEUP_CFG
register must be reset to 0 before loading the firmware.

Instead of during rt2800{pci,usb}_write_firmware it
must actually be done in rt2800_load_firmware() before
resetting the WPDMA_GLO_CFG and PWR_PIN_CFG registers.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of printing a warning when the PID, ACK, or WCID of
an entry don't match the TX status report, we should skip the
entry to search for the entry which actually does match
the TX status data.

This reduces the number of watchdog errors on the TX queues
for rt2800usb, and seems to improve the reliability of the
TX flow a bit.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Similar to rt2800_wait_wpdma_ready() we can add a
function to waiting until the CSR is ready. This
centralizes some additional code into rt2800lib.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Variables containing queue ids are called qid everywhere else, hence
rename the queue field in txentry_desc to qid as well.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

According to the hardware documentation, the MIC failure bit is only
valid if the frame was decrypted using a valid TKIP key and is not a
fragment.
In some setups I've seen hardware-reported MIC failures on an AP that
was configured for CCMP only, so it's clear that additional checks are
necessary.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch was adapted from 06f7bc7d
(from linus's linux-2.6 tree of kernel.org)

here's the original message:
    The queue stopping/waking functionality was broken in a way that could
    cause huge latencies in TX transfers and even cause the TX to stall in the
    right circumstances. Correct these problems.
Signed-off-by: NDenis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Acked-by: NKalle Valo <kvalo@adurom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add the trivial support for runtime interface
type changes to mac80211_hwsim for testing.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While scanning, ANI is triggered unnecessarily where sta is in
unassociated state. And cancelling ani work in ath9k_htc_stop
is not required.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With the scan callback now being callable from
any context, these unlocks/locks can go away.
This makes the code easier to understand, since
callers of these functions must no longer be
aware that the mutex may be dropped.

As Stanislaw is working on iwlwifi scanning, I
didn't change it to take advantage of the new
mac80211 semantics.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All major Atheros customers require the led to be in continuous
ON state rather than the blinking pattern.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If the symbol offset is 46, it will be counted in both
the third and fourth bytes of the mask, and in this
case the shift will be negative which can pollute
high order bits in the mask.  This may negatively impact
OFDM symbol detection.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There was a small misordering here.  In the original code, if we were to
go to err_free_ah then it wouldn't free the irq.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We're now ready to start using multiple contexts.
We do this by keeping track of the valid interface
types per context (exclusive [ibss] and normal)
and checking which context is "free" when a new
interface is added.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

It is necessary that the PAN context always
use the same beacon interval as the BSS
context unless it is in dual-station mode,
ie. the PAN context is a station as well,
so implement that.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The PAN context requires also getting
RXON timing when we send an unassociated
RXON in some cases.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Sometimes we need to send RXON timing even
when we don't have a virtual interface yet,
so pass the context and allow passing one
without a virtual interface pointer.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

In order for the microcode to be able to handle
multiple interfaces, we need to give it the PAN
parameters that state how to allocate the time
between the two interfaces. Do this, and update
it wherever necessary.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Newer AGN microcode requires know the beacon
before starting the AP so that it can start
beaconing right away. Implement that.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The PAN functionality requires us to send the
timing including a valid DTIM period to the
microcode before associating, so request this
data from mac80211 and send it to the device.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Frames for different contexts need to be put
on different queues, and multicast after DTIM
frames have a special queue yet which also
depends on the context, so put all this into
the context.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Since we have the beacon context now, we no
longer need to rely on iw_mode but can check
the beacon context interface's type. However,
that check must be in the work item instead
due to locking constraints (mutex must be
held when dereferencing beacon_ctx pointer).
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Detect whether or not the ucode is PAN
capable and adjust the valid contexts
accordingly. To be able to do this, add
the PAN context to the array as well.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Define the new host commands and notifications
	REPLY_WIPAN_PARAMS
	REPLY_WIPAN_RXON
	REPLY_WIPAN_RXON_TIMING
	REPLY_WIPAN_RXON_ASSOC
	REPLY_WIPAN_QOS_PARAM
	REPLY_WIPAN_WEPKEY
	REPLY_WIPAN_P2P_CHANNEL_SWITCH
	REPLY_WIPAN_NOA_NOTIFICATION

and their corresponding structures along with the PAN
station flag, the PAN AP sta ID and new dev types for
the second context.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Only one context can be beaconing at a time,
but we need to track which one. Introduce a
new variable priv->beacon_ctx to do that.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

A lot of HT configuration semantically belongs into
the context, even if right now it will never be
different between contexts. Move it so we're better
prepared for future changes in mac80211.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Sometimes we only pass around station
pointers but need to find the context
they belong to, so store it in there.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Since the default context is initialised to zero,
and the default flags are zero, no more code is
needed to initialise them right now, but another
context can have different default flags.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

HW crypto needs to be aware of the context, and there
are different command IDs for the WEP keys per context,
so move the key tracking variables and command IDs into
the context structure.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Each context needs to use a different AP sta
ID, so we need to move that into the context
struct instead of hardcoding it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The dwell time should at least fit into all
context's beacon intervals.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>