As there is currently no-one to take care of this old !MMU target and as its
support in recent kernels is a bit rotten, remove this at91x40 support and the
board file associated with it (at91eb01).
There are modern ARM !MMU in Mainline now so this target is not interesting for
building tests anymore. It would be better to start from these modern ARM !MMU
platforms to reintroduce at91x40 support if needed.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NGreg Ungerer <gerg@uclinux.org>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

we will select now the DBGU used by the soc at Kconfig level

For the DEBUG_LL and early_printk this will allow to select which DBGU to use
this will also allow to select them when multiple SOC are enabled
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

to make the soc base specified at runtime instead of compiled time
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The AT91x40 family doesn't have the debug unit like its bigger brothers.
But it does have the ID and extension registers (with the bit meanings
the same). Reorganize at91_dbgu.h to cater for this.

This also affects the load uncompressor, since it outputs to the
debug port.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add support for the Atmel AT91SAM9XE range of processors.  These are
basically AT91SAM9260's with different amounts of internal SRAM and
Flash.

We make use of the existing AT91SAM9260 support, but just perform
run-time detection of the size of the internal SRAM.

Original patch from Nicolas Ferre.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Now that Linux includes support for the Atmel AT91SAM9260 and
AT91SAM9261 processors in addition to the original Atmel AT91RM9200
(with support for more AT91 processors pending), the "mach-at91rm9200"
and "arch-at91rm9200" directories should be renamed to indicate their
more generic nature.

The following git commands should be run BEFORE applying this patch:
  git-mv arch/arm/mach-at91rm9200 arch/arm/mach-at91
  git-mv include/asm-arm/arch-at91rm9200 include/asm-arm/arch-at91
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The AT91RM9200 system header file (at91rm9200_sys.h) has been split into
separate header files for each peripheral.  This was necessary since
some of the system peripherals are also used on AT91SAM9260 and
AT91SAM9261.

The new SAM9-specific register bits have also been defined.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>