Instead of using physical addresses for accounting of extra memory
areas available for ballooning switch to pfns as this is much less
error prone regarding partial pages.
Reported-by: NRoger Pau Monné <roger.pau@citrix.com>
Tested-by: NRoger Pau Monné <roger.pau@citrix.com>
Signed-off-by: NJuergen Gross <jgross@suse.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

When a pv-domain (including dom0) is started it tries to size it's
p2m list according to the maximum possible memory amount it ever can
achieve. Limit the initial maximum memory size to the architectural
limit of the hardware in order to avoid overflows during remapping
of memory.

This problem will occur when dom0 is started with an initial memory
size being a multiple of 1GB, but without specifying it's maximum
memory size. The kernel must be configured without
CONFIG_XEN_BALLOON_MEMORY_HOTPLUG for the problem to happen.
Reported-by: NRoger Pau Monné <roger.pau@citrix.com>
Tested-by: NRoger Pau Monné <roger.pau@citrix.com>
Signed-off-by: NJuergen Gross <jgross@suse.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

Commit b1c9f169047b ("xen: split counting of extra memory pages...")
introduced an error when dom0 was started with limited memory occurring
only on some hardware.

The problem arises in case dom0 is started with initial memory and
maximum memory being the same. The kernel must be configured without
CONFIG_XEN_BALLOON_MEMORY_HOTPLUG for the problem to happen. If all
of this is true and the E820 map of the machine is sparse (some areas
are not covered) then the machine might crash early in the boot
process.

An example E820 map triggering the problem looks like this:

[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009d7ff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009d800-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000cf7fafff] usable
[    0.000000] BIOS-e820: [mem 0x00000000cf7fb000-0x00000000cf95ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000cf960000-0x00000000cfb62fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000cfb63000-0x00000000cfd14fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000cfd15000-0x00000000cfd61fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000cfd62000-0x00000000cfd6cfff] ACPI data
[    0.000000] BIOS-e820: [mem 0x00000000cfd6d000-0x00000000cfd6ffff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000cfd70000-0x00000000cfd70fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000cfd71000-0x00000000cfea8fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000cfea9000-0x00000000cfeb9fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000cfeba000-0x00000000cfecafff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000cfecb000-0x00000000cfecbfff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000cfecc000-0x00000000cfedbfff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000cfedc000-0x00000000cfedcfff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000cfedd000-0x00000000cfeddfff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000cfede000-0x00000000cfee3fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000cfee4000-0x00000000cfef6fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000cfef7000-0x00000000cfefffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec10000-0x00000000fec10fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed40000-0x00000000fed44fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed61000-0x00000000fed70fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed80000-0x00000000fed8ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100001000-0x000000020effffff] usable

In this case the area a0000-dffff isn't present in the map. This will
confuse the memory setup of the domain when remapping the memory from
such holes to populated areas.

To avoid the problem the accounting of to be remapped memory has to
count such holes in the E820 map as well.
Reported-by: NBoris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: NJuergen Gross <jgross@suse.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

Commit b1c9f169047b ("xen: split counting of extra memory pages...")
introduced an error when dom0 was started with limited memory.

The problem arises in case dom0 is started with initial memory and
maximum memory being the same and exactly a multiple of 1 GB. The
kernel must be configured without CONFIG_XEN_BALLOON_MEMORY_HOTPLUG
for the problem to happen. In this case it will crash very early
during boot due to the virtual mapped p2m list not being large
enough to be able to remap any memory:

(XEN) Freed 304kB init memory.
mapping kernel into physical memory
about to get started...
(XEN) traps.c:459:d0v0 Unhandled invalid opcode fault/trap [#6] on VCPU 0 [ec=0000]
(XEN) domain_crash_sync called from entry.S: fault at ffff82d080229a93 create_bounce_frame+0x12b/0x13a
(XEN) Domain 0 (vcpu#0) crashed on cpu#0:
(XEN) ----[ Xen-4.5.2-pre  x86_64  debug=n Not tainted ]----
(XEN) CPU:    0
(XEN) RIP:    e033:[<ffffffff81d120cb>]
(XEN) RFLAGS: 0000000000000206   EM: 1 CONTEXT: pv guest (d0v0)
(XEN) rax: ffffffff81db2000   rbx: 000000004d000000   rcx: 0000000000000000
(XEN) rdx: 000000004d000000   rsi: 0000000000063000   rdi: 000000004d063000
(XEN) rbp: ffffffff81c03d78   rsp: ffffffff81c03d28   r8:  0000000000023000
(XEN) r9:  00000001040ff000   r10: 0000000000007ff0   r11: 0000000000000000
(XEN) r12: 0000000000063000   r13: 000000000004d000   r14: 0000000000000063
(XEN) r15: 0000000000000063   cr0: 0000000080050033   cr4: 00000000000006f0
(XEN) cr3: 0000000105c0f000   cr2: ffffc90000268000
(XEN) ds: 0000   es: 0000   fs: 0000   gs: 0000   ss: e02b   cs: e033
(XEN) Guest stack trace from rsp=ffffffff81c03d28:
(XEN)   0000000000000000 0000000000000000 ffffffff81d120cb 000000010000e030
(XEN)   0000000000010006 ffffffff81c03d68 000000000000e02b ffffffffffffffff
(XEN)   0000000000000063 000000000004d063 ffffffff81c03de8 ffffffff81d130a7
(XEN)   ffffffff81c03de8 000000000004d000 00000001040ff000 0000000000105db1
(XEN)   00000001040ff001 000000000004d062 ffff8800092d6ff8 0000000002027000
(XEN)   ffff8800094d8340 ffff8800092d6ff8 00003ffffffff000 ffff8800092d7ff8
(XEN)   ffffffff81c03e48 ffffffff81d13c43 ffff8800094d8000 ffff8800094d9000
(XEN)   0000000000000000 ffff8800092d6000 00000000092d6000 000000004cfbf000
(XEN)   00000000092d6000 00000000052d5442 0000000000000000 0000000000000000
(XEN)   ffffffff81c03ed8 ffffffff81d185c1 0000000000000000 0000000000000000
(XEN)   ffffffff81c03e78 ffffffff810f8ca4 ffffffff81c03ed8 ffffffff8171a15d
(XEN)   0000000000000010 ffffffff81c03ee8 0000000000000000 0000000000000000
(XEN)   ffffffff81f0e402 ffffffffffffffff ffffffff81dae900 0000000000000000
(XEN)   0000000000000000 0000000000000000 ffffffff81c03f28 ffffffff81d0cf0f
(XEN)   0000000000000000 0000000000000000 0000000000000000 ffffffff81db82e0
(XEN)   0000000000000000 0000000000000000 0000000000000000 0000000000000000
(XEN)   ffffffff81c03f38 ffffffff81d0c603 ffffffff81c03ff8 ffffffff81d11c86
(XEN)   0300000100000032 0000000000000005 0000000000000020 0000000000000000
(XEN)   0000000000000000 0000000000000000 0000000000000000 0000000000000000
(XEN)   0000000000000000 0000000000000000 0000000000000000 0000000000000000
(XEN) Domain 0 crashed: rebooting machine in 5 seconds.

This can be avoided by allocating aneough space for the p2m to cover
the maximum memory of dom0 plus the identity mapped holes required
for PCI space, BIOS etc.
Reported-by: NBoris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: NJuergen Gross <jgross@suse.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

Since VPMU code emulates RDPMC instruction with RDMSR and because hypervisor
does not emulate it there is no reason to try setting CR4's PCE bit (and the
hypervisor will warn on seeing it set).
Signed-off-by: NBoris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

Add PMU emulation code that runs when we are processing a PMU interrupt.
This code will allow us not to trap to hypervisor on each MSR/LVTPC access
(of which there may be quite a few in the handler).
Signed-off-by: NBoris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

Provide interfaces for recognizing accesses to PMU-related MSRs and
LVTPC APIC and process these accesses in Xen PMU code.

(The interrupt handler performs XENPMU_flush right away in the beginning
since no PMU emulation is available. It will be added with a later patch).
Signed-off-by: NBoris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

AMD and Intel PMU register initialization and helpers that determine
whether a register belongs to PMU.

This and some of subsequent PMU emulation code is somewhat similar to
Xen's PMU implementation.
Signed-off-by: NBoris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

Map shared data structure that will hold CPU registers, VPMU context,
V/PCPU IDs of the CPU interrupted by PMU interrupt. Hypervisor fills
this information in its handler and passes it to the guest for further
processing.

Set up PMU VIRQ.

Now that perf infrastructure will assume that PMU is available on a PV
guest we need to be careful and make sure that accesses via RDPMC
instruction don't cause fatal traps by the hypervisor. Provide a nop
RDPMC handler.

For the same reason avoid issuing a warning on a write to APIC's LVTPC.

Both of these will be made functional in later patches.
Signed-off-by: NBoris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

Set Xen's PMU mode via /sys/hypervisor/pmu/pmu_mode. Add XENPMU hypercall.
Signed-off-by: NBoris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

Cleanup by removing arch/x86/xen/p2m.h as it isn't needed any more.

Most definitions in this file are used in p2m.c only. Move those into
p2m.c.

set_phys_range_identity() is already declared in
arch/x86/include/asm/xen/page.h, add __init annotation there.

MAX_REMAP_RANGES isn't used at all, just delete it.

The only define left is P2M_PER_PAGE which is moved to page.h as well.
Signed-off-by: NJuergen Gross <jgross@suse.com>
Acked-by: NKonrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

64 bit pv-domains under Xen are limited to 512 GB of RAM today. The
main reason has been the 3 level p2m tree, which was replaced by the
virtual mapped linear p2m list. Parallel to the p2m list which is
being used by the kernel itself there is a 3 level mfn tree for usage
by the Xen tools and eventually for crash dump analysis. For this tree
the linear p2m list can serve as a replacement, too. As the kernel
can't know whether the tools are capable of dealing with the p2m list
instead of the mfn tree, the limit of 512 GB can't be dropped in all
cases.

This patch replaces the hard limit by a kernel parameter which tells
the kernel to obey the 512 GB limit or not. The default is selected by
a configuration parameter which specifies whether the 512 GB limit
should be active per default for domUs (domain save/restore/migration
and crash dump analysis are affected).

Memory above the domain limit is returned to the hypervisor instead of
being identity mapped, which was wrong anyway.

The kernel configuration parameter to specify the maximum size of a
domain can be deleted, as it is not relevant any more.
Signed-off-by: NJuergen Gross <jgross@suse.com>
Acked-by: NKonrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

Check whether the hypervisor supplied p2m list is placed at a location
which is conflicting with the target E820 map. If this is the case
relocate it to a new area unused up to now and compliant to the E820
map.

As the p2m list might by huge (up to several GB) and is required to be
mapped virtually, set up a temporary mapping for the copied list.

For pvh domains just delete the p2m related information from start
info instead of reserving the p2m memory, as we don't need it at all.

For 32 bit kernels adjust the memblock_reserve() parameters in order
to cover the page tables only. This requires to memblock_reserve() the
start_info page on it's own.
Signed-off-by: NJuergen Gross <jgross@suse.com>
Acked-by: NKonrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

Some special pages containing interfaces to xen are being reserved
implicitly only today. The memblock_reserve() call to reserve them is
meant to reserve the p2m list supplied by xen. It is just reserving
not only the p2m list itself, but some more pages up to the start of
the xen built page tables.

To be able to move the p2m list to another pfn range, which is needed
for support of huge RAM, this memblock_reserve() must be split up to
cover all affected reserved pages explicitly.

The affected pages are:
- start_info page
- xenstore ring (might be missing, mfn is 0 in this case)
- console ring (not for initial domain)
Signed-off-by: NJuergen Gross <jgross@suse.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

Check whether the initrd is placed at a location which is conflicting
with the target E820 map. If this is the case relocate it to a new
area unused up to now and compliant to the E820 map.
Signed-off-by: NJuergen Gross <jgross@suse.com>
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>
Acked-by: NKonrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

Check whether the page tables built by the domain builder are at
memory addresses which are in conflict with the target memory map.
If this is the case just panic instead of running into problems
later.
Signed-off-by: NJuergen Gross <jgross@suse.com>
Acked-by: NKonrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

Checks whether the pre-allocated memory of the loaded kernel is in
conflict with the target memory map. If this is the case, just panic
instead of run into problems later, as there is nothing we can do
to repair this situation.
Signed-off-by: NJuergen Gross <jgross@suse.com>
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>
Acked-by: NKonrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

For being able to relocate pre-allocated data areas like initrd or
p2m list it is mandatory to find a contiguous memory area which is
not yet in use and doesn't conflict with the memory map we want to
be in effect.

In case such an area is found reserve it at once as this will be
required to be done in any case.
Signed-off-by: NJuergen Gross <jgross@suse.com>
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>
Acked-by: NKonrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

Provide a service routine to check a physical memory area against the
E820 map. The routine will return false if the complete area is RAM
according to the E820 map and true otherwise.
Signed-off-by: NJuergen Gross <jgross@suse.com>
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>
Acked-by: NKonrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

Memory pages in the initial memory setup done by the Xen hypervisor
conflicting with the target E820 map are remapped. In order to do this
those pages are counted and remapped in xen_set_identity_and_remap().

Split the counting from the remapping operation to be able to setup
the needed memory sizes in time but doing the remap operation at a
later time. This enables us to simplify the interface to
xen_set_identity_and_remap() as the number of remapped and released
pages is no longer needed here.

Finally move the remapping further down to prepare relocating
conflicting memory contents before the memory might be clobbered by
xen_set_identity_and_remap(). This requires to not destroy the Xen
E820 map when the one for the system is being constructed.
Signed-off-by: NJuergen Gross <jgross@suse.com>
Acked-by: NKonrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

Instead of using a function local static e820 map in xen_memory_setup()
and calling various functions in the same source with the map as a
parameter use a map directly accessible by all functions in the source.
Signed-off-by: NJuergen Gross <jgross@suse.com>
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>
Acked-by: NKonrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

Direct Xen to place the initial P->M table outside of the initial
mapping, as otherwise the 1G (implementation) / 2G (theoretical)
restriction on the size of the initial mapping limits the amount
of memory a domain can be handed initially.

As the initial P->M table is copied rather early during boot to
domain private memory and it's initial virtual mapping is dropped,
the easiest way to avoid virtual address conflicts with other
addresses in the kernel is to use a user address area for the
virtual address of the initial P->M table. This allows us to just
throw away the page tables of the initial mapping after the copy
without having to care about address invalidation.

It should be noted that this patch won't enable a pv-domain to USE
more than 512 GB of RAM. It just enables it to be started with a
P->M table covering more memory. This is especially important for
being able to boot a Dom0 on a system with more than 512 GB memory.
Signed-off-by: NJuergen Gross <jgross@suse.com>
Based-on-patch-by: NJan Beulich <jbeulich@suse.com>
Acked-by: NKonrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

In case the Xen tools indicate they don't need the p2m 3 level tree
as they support the virtual mapped linear p2m list, just omit building
the tree.
Signed-off-by: NJuergen Gross <jgross@suse.com>
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>
Acked-by: NKonrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

The virtual address of the linear p2m list should be stored in the
shared info structure read by the Xen tools to be able to support
64 bit pv-domains larger than 512 GB. Additionally the linear p2m
list interface includes a generation count which is changed prior
to and after each mapping change of the p2m list. Reading the
generation count the Xen tools can detect changes of the mappings
and re-read the p2m list eventually.
Signed-off-by: NJuergen Gross <jgross@suse.com>
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>
Acked-by: NKonrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

xen_has_pv_devices() has no parameters, so use the normal void
parameter convention to make it match the prototype in the header file
include/xen/platform_pci.h.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

Since commit feb44f1f (x86/xen:
Provide a "Xen PV" APIC driver to support >255 VCPUs) Xen guests need
a full APIC driver and thus should depend on X86_LOCAL_APIC.

This fixes an i386 build failure with !SMP && !CONFIG_X86_UP_APIC by
disabling Xen support in this configuration.

Users needing Xen support in a non-SMP i386 kernel will need to enable
CONFIG_X86_UP_APIC.
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Cc: <stable@vger.kernel.org>

It turns out that a PV domU also requires the "Xen PV" APIC
driver. Otherwise, the flat driver is used and we get stuck in busy
loops that never exit, such as in this stack trace:

(gdb) target remote localhost:9999
Remote debugging using localhost:9999
__xapic_wait_icr_idle () at ./arch/x86/include/asm/ipi.h:56
56              while (native_apic_mem_read(APIC_ICR) & APIC_ICR_BUSY)
(gdb) bt
 #0  __xapic_wait_icr_idle () at ./arch/x86/include/asm/ipi.h:56
 #1  __default_send_IPI_shortcut (shortcut=<optimized out>,
dest=<optimized out>, vector=<optimized out>) at
./arch/x86/include/asm/ipi.h:75
 #2  apic_send_IPI_self (vector=246) at arch/x86/kernel/apic/probe_64.c:54
 #3  0xffffffff81011336 in arch_irq_work_raise () at
arch/x86/kernel/irq_work.c:47
 #4  0xffffffff8114990c in irq_work_queue (work=0xffff88000fc0e400) at
kernel/irq_work.c:100
 #5  0xffffffff8110c29d in wake_up_klogd () at kernel/printk/printk.c:2633
 #6  0xffffffff8110ca60 in vprintk_emit (facility=0, level=<optimized
out>, dict=0x0 <irq_stack_union>, dictlen=<optimized out>,
fmt=<optimized out>, args=<optimized out>)
    at kernel/printk/printk.c:1778
 #7  0xffffffff816010c8 in printk (fmt=<optimized out>) at
kernel/printk/printk.c:1868
 #8  0xffffffffc00013ea in ?? ()
 #9  0x0000000000000000 in ?? ()

Mailing-list-thread: https://lkml.org/lkml/2015/8/4/755Signed-off-by: NJason A. Donenfeld <Jason@zx2c4.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

The update_va_mapping hypercall can fail if the VA isn't present
in the guest's page tables.  Under certain loads, this can
result in an OOPS when the target address is in unpopulated vmap
space.

While we're at it, add comments to help explain what's going on.

This isn't a great long-term fix.  This code should probably be
changed to use something like set_memory_ro.
Signed-off-by: NAndy Lutomirski <luto@kernel.org>
Cc: Andrew Cooper <andrew.cooper3@citrix.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: David Vrabel <dvrabel@cantab.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jan Beulich <jbeulich@suse.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: security@kernel.org <security@kernel.org>
Cc: <stable@vger.kernel.org>
Cc: xen-devel <xen-devel@lists.xen.org>
Link: http://lkml.kernel.org/r/0b0e55b995cda11e7829f140b833ef932fcabe3a.1438291540.git.luto@kernel.orgSigned-off-by: NIngo Molnar <mingo@kernel.org>

Migrate xen driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.

This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.

Callbacks aren't implemented for modes where we weren't doing anything.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Cc: linaro-kernel@lists.linaro.org
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: xen-devel@lists.xenproject.org (moderated list:XEN HYPERVISOR INTERFACE)
Link: http://lkml.kernel.org/r/881eea6e1a3d483cd33e044cd34827cce26a57fd.1437042675.git.viresh.kumar@linaro.orgSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

We've had ->read_tsc() and ->read_tscp() paravirt hooks since
the very beginning of paravirt, i.e.,

  d3561b7f ("[PATCH] paravirt: header and stubs for paravirtualisation").

AFAICT, the only paravirt guest implementation that ever
replaced these calls was vmware, and it's gone. Arguably even
vmware shouldn't have hooked RDTSC -- we fully support systems
that don't have a TSC at all, so there's no point for a paravirt
implementation to pretend that we have a TSC but to replace it.

I also doubt that these hooks actually worked. Calls to rdtscl()
and rdtscll(), which respected the hooks, were used seemingly
interchangeably with native_read_tsc(), which did not.

Just remove them. If anyone ever needs them again, they can try
to make a case for why they need them.

Before, on a paravirt config:
  text    	data     bss     dec     hex filename
  12618257      1816384 1093632 15528273 ecf151 vmlinux

After:
  text		data     bss     dec     hex filename
  12617207      1816384 1093632 15527223 eced37 vmlinux
Signed-off-by: NAndy Lutomirski <luto@kernel.org>
Signed-off-by: NBorislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Cc: virtualization@lists.linux-foundation.org
Link: http://lkml.kernel.org/r/d08a2600fb298af163681e5efd8e599d889a5b97.1434501121.git.luto@kernel.orgSigned-off-by: NIngo Molnar <mingo@kernel.org>

The 'system_call' entry points differ starkly between native 32-bit and 64-bit
kernels: on 32-bit kernels it defines the INT 0x80 entry point, while on
64-bit it's the SYSCALL entry point.

This is pretty confusing when looking at generic code, and it also obscures
the nature of the entry point at the assembly level.

So unangle this by splitting the name into its two uses:

	system_call (32) -> entry_INT80_32
	system_call (64) -> entry_SYSCALL_64

As per the generic naming scheme for x86 system call entry points:

	entry_MNEMONIC_qualifier

where 'qualifier' is one of _32, _64 or _compat.

Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NIngo Molnar <mingo@kernel.org>

x86/asm/entry: Untangle 'ia32_sysenter_target' into two entry points: entry_SYSENTER_32 and entry_SYSENTER_compat

So the SYSENTER instruction is pretty quirky and it has different behavior
depending on bitness and CPU maker.

Yet we create a false sense of coherency by naming it 'ia32_sysenter_target'
in both of the cases.

Split the name into its two uses:

	ia32_sysenter_target (32)    -> entry_SYSENTER_32
	ia32_sysenter_target (64)    -> entry_SYSENTER_compat

As per the generic naming scheme for x86 system call entry points:

	entry_MNEMONIC_qualifier

where 'qualifier' is one of _32, _64 or _compat.

Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NIngo Molnar <mingo@kernel.org>

Rename the following system call entry points:

	ia32_cstar_target       -> entry_SYSCALL_compat
	ia32_syscall            -> entry_INT80_compat

The generic naming scheme for x86 system call entry points is:

	entry_MNEMONIC_qualifier

where 'qualifier' is one of _32, _64 or _compat.

Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NIngo Molnar <mingo@kernel.org>

In the case when PAT is disabled on the command line with
"nopat" or when virtualization doesn't support PAT (correctly) -
see

  9d34cfdf ("x86: Don't rely on VMWare emulating PAT MSR correctly").

we emulate it using the PWT and PCD cache attribute bits. Get
rid of boot_pat_state while at it.

Based on a conglomerate patch from Toshi Kani.
Signed-off-by: NBorislav Petkov <bp@suse.de>
Reviewed-by: NToshi Kani <toshi.kani@hp.com>
Acked-by: NJuergen Gross <jgross@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Elliott@hp.com
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: arnd@arndb.de
Cc: hch@lst.de
Cc: hmh@hmh.eng.br
Cc: konrad.wilk@oracle.com
Cc: linux-mm <linux-mm@kvack.org>
Cc: linux-nvdimm@lists.01.org
Cc: stefan.bader@canonical.com
Cc: yigal@plexistor.com
Link: http://lkml.kernel.org/r/1433436928-31903-3-git-send-email-bp@alien8.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

Nothing in <asm/io.h> uses anything from <linux/vmalloc.h>, so
remove it from there and fix up the resulting build problems
triggered on x86 {64|32}-bit {def|allmod|allno}configs.

The breakages were triggering in places where x86 builds relied
on vmalloc() facilities but did not include <linux/vmalloc.h>
explicitly and relied on the implicit inclusion via <asm/io.h>.

Also add:

  - <linux/init.h> to <linux/io.h>
  - <asm/pgtable_types> to <asm/io.h>

... which were two other implicit header file dependencies.
Suggested-by: NDavid Miller <davem@davemloft.net>
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
[ Tidied up the changelog. ]
Acked-by: NDavid Miller <davem@davemloft.net>
Acked-by: NTakashi Iwai <tiwai@suse.de>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Colin Cross <ccross@android.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: James E.J. Bottomley <JBottomley@odin.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Kristen Carlson Accardi <kristen@linux.intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Suma Ramars <sramars@cisco.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: NIngo Molnar <mingo@kernel.org>

After the latest round of cleanups, fpu__cpu_init() has become
a simple call to fpu__init_cpu().

Rename fpu__init_cpu() to fpu__cpu_init() and remove the
extra layer.
Reviewed-by: NBorislav Petkov <bp@alien8.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@kernel.org>

fpu_init() is a bit of a misnomer in that it (falsely) creates the
impression that it's related to the (old) fpu_finit() function,
which initializes FPU ctx state.

Rename it to fpu__cpu_init() to make its boot time initialization
clear, and to move it to the fpu__*() namespace.

Also fix and extend its comment block to point out that it's
called not only on the boot CPU, but on secondary CPUs as well.
Reviewed-by: NBorislav Petkov <bp@alien8.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@kernel.org>

Valentin Rothberg reported that we use CONFIG_QUEUED_SPINLOCKS
in arch/x86/kernel/paravirt_patch_32.c, while the symbol is
called CONFIG_QUEUED_SPINLOCK. (Note the extra 'S')

But the typo was natural: the proper English term for such
a generic object would be 'queued spinlocks' - so rename
this and related symbols accordingly to the plural form.
Reported-by: NValentin Rothberg <valentinrothberg@gmail.com>
Cc: Douglas Hatch <doug.hatch@hp.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <Waiman.Long@hp.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NIngo Molnar <mingo@kernel.org>

32-bit code has PER_CPU_VAR(cpu_current_top_of_stack).
64-bit code uses somewhat more obscure: PER_CPU_VAR(cpu_tss + TSS_sp0).

Define the 'cpu_current_top_of_stack' macro on CONFIG_X86_64
as well so that the PER_CPU_VAR(cpu_current_top_of_stack)
expression can be used in both 32-bit and 64-bit code.
Signed-off-by: NDenys Vlasenko <dvlasenk@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Drewry <wad@chromium.org>
Link: http://lkml.kernel.org/r/1429889495-27850-3-git-send-email-dvlasenk@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

PER_CPU_VAR(kernel_stack) is redundant:

  - On the 64-bit build, we can use PER_CPU_VAR(cpu_tss + TSS_sp0).
  - On the 32-bit build, we can use PER_CPU_VAR(cpu_current_top_of_stack).

PER_CPU_VAR(kernel_stack) will be deleted by a separate change.
Signed-off-by: NDenys Vlasenko <dvlasenk@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Drewry <wad@chromium.org>
Link: http://lkml.kernel.org/r/1429889495-27850-1-git-send-email-dvlasenk@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>