ftdi_sio: Update RTS and DTR simultaneously, using a single control URB
instead of separate control URBs for RTS and DTR.  Reinhard Bergmann
observed time differences of up to 680 ms with his application on a
2.4.22 kernel when RTS and DTR were updated using separate control
URBs, which is unacceptable.
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The attached patch adds the following new devices to the ftdi_sio driver:

* microHAM USB-Y6 and USB-Y8 devices submitted by Justin Burket (KL1RL).
* Evolution Robotics ER1 Control Module submitted by Shawn M.  Lavelle.
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

In the patch from:

http://www.uwsg.iu.edu/hypermail/linux/kernel/0506.3/0985.html

Is the the following line suppose inside the if CONFIG_PCI=n

  #define pci_dma_burst_advice(pdev, strat, strategy_parameter) do { } while (0)
Signed-off-by: NKumar Gala <kumar.gala@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The setup-bus code doesn't work correctly for configurations
with more than one display adapter in the same PCI domain.
This stuff actually is a leftover of an early 2.4 PCI setup code
and apparently it stopped working after some "bridge_ctl" changes.
So the best thing we can do is just to remove it and rely on the fact
that any firmware *has* to configure VGA port forwarding for the boot
display device properly.

But then we need to ensure that the bus->bridge_ctl will always
contain valid information collected at the probe time, therefore
the following change in pci_scan_bridge() is needed.
Signed-off-by: NIvan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

There are ROMs reporting that their size exceeds their PCI ROM
resource window. This patch returns the minimum of the resource window
size or the size in the ROM.  An example of this breakage is the XGI
Volari Z7.
Signed-off-by: NJon Smirl <jonsmirl@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Patch against 2.6.12 to unhide SMBus on Toshiba Centrino laptops using
Intel 82855PM chipset.  Tested on Toshiba Tecra M2.
Signed-off-by: NDaniele Gaffuri <d.gaffuri@reply.it>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch was sent first time very long time ago,
but magically was disapeared, it probably exists
in your queue, but to be sure, I resend it.
If can not be applied cleanly after your w1 queue is flushed
into upstrem tree, just drop it.
Thanks.

Patch from Michael Farmbauer <michl@baldrian.franken.de>.
Signed-off-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The 24RF08 corruption prevention in the eeprom and max6875 drivers wasn't
complete. For one thing, the additional quick write should happen as soon
as possible and unconditionally, while both drivers had error paths before.
For another, when a given chip is forced, the core does not emit a quick
write, so a second quick write would cause the corruption rather than
prevent it.

I plan to move the corruption prevention in the core in the long run, so
that individual drivers don't have to care anymore. But I need to merge
i2c_probe and i2c_detect before I do (work in progress).
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Two log messages lack their trailing new line in i2c-core. I'd swear I had
fixed them already, but it seems not. Bonus: improved coding style.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

A few i2c drivers were not updated to use time_after() yet.
Signed-off-by: NMarcelo Feitoza Parisi <marcelo@feitoza.com.br>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

A few split string in i2c (and now hwmon) drivers lack a joining space,
causing them to display incorrectly. This trivial patch fixes that up.
Please apply, thanks.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

DS1339 manual, page 6, chapter Date and time operation:
  The DS1339 can be run in either 12-hour or 24-hour mode. Bit 6 of the
  hours register is defined as the 12-hour or 24-hour mode-select bit.
  When high, the 12-hour mode is selected.

Patch below makes ds1337 driver work as documented in manual.
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

I2C-MPC: Restore code removed

A previous patch to remove support for the OCP device model was way
to generious and moved some of the platform device model code, oops.
Signed-off-by: NKumar Gala <kumar.gala@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This was the last agreed upon set of rules, it's probably time we actually add
them to the kernel tree to make them "official".
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

CONFIG_DEBUG_FS=y and CONFIG_SYSFS=n results in the following compile
error:

<--  snip  -->

...
  LD      vmlinux
fs/built-in.o: In function `debugfs_init':
inode.c:(.init.text+0x31be): undefined reference to `kernel_subsys'
make: *** [vmlinux] Error 1

<--  snip  -->
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

o sysfs_dirent's s_mode field should also be updated in sysfs_setattr(), else
  there could be inconsistency in the two fields. s_mode is used while
  ->readdir so as not to bring in the inode to cache.
Signed-off-by: NManeesh Soni <maneesh@in.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

o sysfs_chmod_file() must update the new iattr field in sysfs_dirent else
  the mode change will not be persistent in case of inode evacuation from
  cache.
Signed-off-by: NManeesh Soni <maneesh@in.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NDaniel Walker <dwalker@mvista.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Use the standard hardware page table manipulation macros.
This is possible now that linux works with all 4 levels
of the page tables.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

In an uncensored copy of code from i386 to x86_64 I wound up
with inline assembly with the wrong constraints.  Use input
constraints instead of output constraints.

So I know the assembler will do the right thing specify the size
of the operand lidtq and lgdtq instead of just lidt and lgdt.

Make load_segments use an input constraint, and delete the macro fun.
Without having to reload %cs like I do on i386 this code is noticeably
simpler.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

For some reason I was telling my inline assembly that the
input argument was an output argument.

Playing in the trampoline code I have seen a couple of
instances where lgdt get the wrong size (because the
trampolines run in 16bit mode) so use lgdtl and lidtl to
be explicit.

Additionally gcc-3.3 and gcc-3.4 want's an lvalue for a
memory argument and it doesn't think an array of characters
is an lvalue so use a packed structure instead.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If device_suspend(PMSG_FREEZE) is not ready to be called in
kernel_restart it is definitely not ready to be called in the even more
fickle kernel_kexec.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Some edge problems with the original C rewrite.

Thanks go to Cal Peake, who pinpointed the breakage to the rewrite, and
tested this fixed version.
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

From: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: NDave Jones <davej@redhat.com>

Since the secondary CPUs will not be operating in symetric mode
while they are held in the pen, we need to ensure that the write
to pen_release is visible to them, by flushing the cache.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch fixes the address length checks in the selinux_socket_connect
hook to be no more restrictive than the underlying ipv4 and ipv6 code;
otherwise, this hook can reject valid connect calls.  This patch is in
response to a bug report where an application was calling connect on an
INET6 socket with an address that didn't include the optional scope id and
failing due to these checks.
Signed-off-by: NStephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: NJames Morris <jmorris@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix a buffer overflow vunerabilty in previous cmap patch
Signed-off-by: NJon Smirl <jonsmirl@gmail.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Somewhere recently, the TSC got re-enabled for timekeeping on NUMAQ
machines.  However, the hardware makes these get unsynchronized quite
badly.  So badly, in fact, that the code to fix up the skew can just hang
on boot.

This patch re-disables them.  It's nicely confined to the numaq.c file.  It
would be great if this could make it into 2.6.13, I think it counts as a
bugfix.

Tested on a 16-proc 4-node NUMAQ.
Signed-off-by: NDave Hansen <haveblue@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

(We found this (after a customer complained) and it is in the kernel.org
kernel.  Seems that for CLOCK_MONOTONIC absolute timers and clock_nanosleep
calls both the request time and wall_to_monotonic are subtracted prior to
the normalize resulting in an overflow in the existing normalize test.
This causes the result to be shifted ~4 seconds ahead instead of ~2 seconds
back in time.)

The normalize code in posix-timers.c fails when the tv_nsec member is ~1.2
seconds negative.  This can happen on absolute timers (and
clock_nanosleeps) requested on CLOCK_MONOTONIC (both the request time and
wall_to_monotonic are subtracted resulting in the possibility of a number
close to -2 seconds.)

This fix uses the set_normalized_timespec() (which does not have an
overflow problem) to fix the problem and as a side effect makes the code
cleaner.
Signed-off-by: NGeorge Anzinger <george@mvista.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Actually implement the hostfs "sync" method.
Signed-off-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

printk() calls should include appropriate KERN_* constant.
Signed-off-by: NChristophe Lucas <clucas@rotomalug.org>
Signed-off-by: NDomen Puncer <domen@coderock.org>
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix a typo in wait_stub_done.
Signed-off-by: NBodo Stroesser <bstroesser@fujitsu-siemens.com>
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

update_process_times was missing its irq_enter/irq_exit wrapper.  This caused
ksoftirqd to be scheduled on every clock tick.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

By this point, .is_user has already been set, so this assignment is useless.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

It's wrong to pop a fixed number of words from stack before calling sigreturn,
as the number depends on what code is generated by the compiler for the start
of stub_segv_handler().  What we need is esp containing the address of
sigcontext.  So we explicitly load that pointer into esp.
Signed-off-by: NBodo Stroesser <bstroesser@fujitsu-siemens.com>
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>