small typo fix in ucode_bt_stats_read debugfs file
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is a uCode bug which cause the tx queue id not match scd_flow
in compressed block ack frame, and it need to be addressed in uCode.
Currently, driver will log the information when it happen.

Since it is possible happen very often and we do not want to fill the syslog,
so don't enable the logging by default.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When iwlwifi is compiled w/o debug, we get
this warning:
iwl-agn.c: In function ‘iwlagn_load_firmware’:
iwl-agn.c:2014: warning: passing argument 3 of ‘iwl_print_hex_dump’ discards qualifiers from pointer target type
iwl-debug.h:73: note: expected ‘void *’ but argument is of type ‘const u8 *’

because the const qualifier is missing in the
inline stub. Fix this.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On AR5008-AR9002, other forms of calibration must not be started while
the noise floor calibration is running, as this can create invalid
readings which were sometimes not even recoverable by any further
calibration attempts.

This patch also ensures that the result of noise floor measurements
are processed faster and also allows the result of the initial
calibration on reset to make it into the NF history buffer
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The noise floor history buffer is currently not kept per channel, which
can lead to problems when changing channels from a clean channel to a
noisy one. Also when switching from HT20 to HT40, the noise floor
history buffer is full of measurements, but none of them contain data
for the extension channel, which it needs quite a bit of time to recover
from.

This patch puts all the per-channel calibration data into a single data
structure, and gives the the driver control over whether that is used
per-channel or even not used for some channels.

For ath9k_htc, I decided to keep this per-channel in order to avoid
creating regressions.

For ath9k, the data is kept only for the operating channel, which saves
some space. ath9k_hw takes care of wiping old data when the operating
channel or its channel flags change.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Previously the software scan callback was used to indicate to the hardware,
when it was safe to calibrate. This didn't really work properly, because it
depends on a specific order of software scan callbacks vs. channel changes.
Also, software scans are not the only thing that triggers off-channel
activity, so it's better to use the newly added indication from mac80211 for
this and not use the software scan callback for anything calibration related.

This fixes at least some of the invalid noise floor readings that I've seen
in AP mode on AR9160
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Writes to the analog shift registers, which are issues by the initval
programming function, require a 100 usec delay (similar to AR9002,
but in a different register range).
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Acked-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When updating the PAPRD table in hardware, PAPRD itself needs to be
disabled first, otherwise the hardware can throw a data bus error,
which upsets at least some platforms.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Acked-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The periodic noise floor calibration is broken on this chip family, because
it keeps triggering a software-filtered noise floor calibration, but never
reads the result before uploading the history buffer value to the hardware.

Fix this with a call to ath9k_hw_getnf(), just like on AR9002.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Acked-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On AR9003 the initial noise floor calibration is currently triggered
at the end of the reset without allowing the hardware to update the
baseband settings. This could potentially make scans in noisy
environments a bit more unreliable, so use the same calibration
sequence that is used on AR9002.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Acked-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Releasing the scan mutex while starting scans
can lead to unexpected things happening, so
we shouldn't do that. Fix that and hold the
mutex across the scan triggering.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

commit f84b29ec
Author: Johannes Berg <johannes.berg@intel.com>
Date:   Tue May 18 02:29:13 2010 -0700

    iwlwifi: queue user-initiated scan when doing internal scan

introduced a potential deadlock because it calls
ieee80211_scan_completed() with the priv->mutex
held, but mac80211 may call back into iwlwifi
which would lead to recursive locking. Move this
out from under the mutex.

Cc: stable@kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Marvell 88ec048 is a derivative of its 88e1121r device.  From the programmer's
perspective, the one major difference is the addition of an additional control
bit in Page 2 Register 16 - used to control the padding of odd nibble
preambles.

This patch adds support for this new device, while inheriting as much code as
possible from the existing 88e1121r implementation.
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch addresses an issue seen on 82580 in which the MDICNFG
register will be reset during a single function reset and as a
result we will be unable to communicate with the PHY.  To correct
the issue, added a call to reset_mdicnfg just prior to the first
access of the MDICNFG register in sgnii_uses_mdio.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MAC-PHY interconnect register set on ICH/PCH parts is accessed through
a peephole mechanism by writing an offset to a CSR register.  The offset
for the interconnect's half-duplex control register (which is used in a
jumbo frame workaround for 82579) is incorrect.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a new product ID to the hso driver.
Signed-off-by: NFilip Aben <f.aben@option.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a driver for esd's USB high speed
CAN interface. The driver supports devices with
multiple CAN interfaces.
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The header file l2tp.h should be exported to the installed include/linux/
tree for userspace programs.

This patch fixes compilation errors in L2TP userspace apps which want to
use the new L2TP support introduced in 2.6.35.
Signed-off-by: NJames Chapman <jchapman@katalix.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit fc6055a5 (net: Introduce
skb_orphan_try()) allows an early orphan of the skb and takes care on
tx timestamping, which needs the sk-reference in the skb on driver level.
So does the can-raw socket, which has not been taken into account here.

The patch below adds a 'prevent_sk_orphan' bit in the skb tx shared info,
which fixes the problem discovered by Matthias Fuchs here:

      http://marc.info/?t=128030411900003&r=1&w=2

Even if it's not a primary tx timestamp topic it fits well into some skb
shared tx context. Or should be find a different place for the information to
protect the sk reference until it reaches the driver level?
Signed-off-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 15e83ed7.

As explained by Johannes Berg, the optimization made here is
invalid.  Or, at best, incomplete.

Not only destructor invocation, but conntract entry releasing
must be executed outside of hw IRQ context.

So just checking "skb->destructor" is insufficient.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit ab95bfe0 replaces bridge and macvlan
hooks in __netif_receive_skb(), so dev.c doesn't need to include their headers.
Signed-off-by: NChangli Gao <xiaosuo@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/e1000e/hw.h
	net/bridge/br_device.c
	net/bridge/br_input.c

This patch adds support for RGMII RX/TX delay configuration on marvell 88e1121
and derivatives.  With this patch, PHY_INTERFACE_MODE_RGMII_*ID modes are now
supported on these devices.
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It was possible to use a negative offset in a u32 match to reference
the ethernet header or other parts of the link layer header.
This fixes the regression caused by:

commit fbc2e7d9
Author: Changli Gao <xiaosuo@gmail.com>
Date:   Wed Jun 2 07:32:42 2010 -0700

    cls_u32: use skb_header_pointer() to dereference data safely
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The typo was causing compilation errors since "dev" was not defined.
Signed-off-by: NHenrique Camargo <henrique.camargo@ensitec.com.br>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Synchronize all IRQs when using MSI-X. Similar to ixgbe.
Issue was reported on e1000e, but the patch is also valid for igb.

CC: Jean Delvare <jdelvare@suse.de>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change corrects an issue that resulted in a null pointer dereference
for the addition of VLAN 0 without any VLANs being registered.  Also this
code removes some unnecessary checks for defines and the unnecessary setting
of VLAN flags since that is now handled within the kernel via the
vlan_features.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on original patch/work from Jean Delvare <jdelvare@suse.de>
Synchronize all IRQs when in MSI-X IRQ mode.

Jean's original patch hard coded the sync with the 3 possible vectors,
this patch incorporates more flexibility for the future and aligns
with how igb stores the number of vectors into the adapter structure.

CC: Jean Delvare <jdelvare@suse.de>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Acked-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The pm_qos_add_request call has to register the pm_qos request with the pm_qos
susbsystem before first use of the pm_qos request via
pm_qos_update_request.

As pm_qos changed to use plists there is no benefit in registering and
unregistering the pm_qos request on ifup/ifdown and thus we move the
registering into e1000_open and the unregistering in e1000_close.

This fixes the following warning:

[    1.786060] WARNING: at kernel/pm_qos_params.c:264
pm_qos_update_request+0x28/0x54()
[    1.786088] Hardware name: Latitude E6500
[    1.787045] pm_qos_update_request() called for unknown object
[    1.787966] Modules linked in:
[    1.788940] Pid: 1, comm: swapper Not tainted 2.6.35-rc5-mmotm0719 #1
[    1.790035] Call Trace:
[    1.791121]  [<ffffffff81037335>] warn_slowpath_common+0x80/0x98
[    1.792205]  [<ffffffff810373e1>] warn_slowpath_fmt+0x41/0x43
[    1.793279]  [<ffffffff81057c14>] pm_qos_update_request+0x28/0x54
[    1.794347]  [<ffffffff8134889e>] e1000_configure+0x421/0x459
[    1.795393]  [<ffffffff8134afbd>] e1000_open+0xbd/0x37c
[    1.796436]  [<ffffffff8105743a>] ? raw_notifier_call_chain+0xf/0x11
[    1.797491]  [<ffffffff8145f948>] __dev_open+0xae/0xe2
[    1.798547]  [<ffffffff8145f997>] dev_open+0x1b/0x49
[    1.799612]  [<ffffffff8146e36e>] netpoll_setup+0x84/0x259
[    1.800685]  [<ffffffff81b5037c>] init_netconsole+0xbc/0x21f
[    1.801744]  [<ffffffff81b5026c>] ? sir_wq_init+0x0/0x35
[    1.802793]  [<ffffffff81b502c0>] ? init_netconsole+0x0/0x21f
[    1.803845]  [<ffffffff810002ff>] do_one_initcall+0x7a/0x12f
[    1.804885]  [<ffffffff81b2ccae>] kernel_init+0x138/0x1c2
[    1.805915]  [<ffffffff81003554>] kernel_thread_helper+0x4/0x10
[    1.806937]  [<ffffffff81590e00>] ? restore_args+0x0/0x30
[    1.807955]  [<ffffffff81b2cb76>] ? kernel_init+0x0/0x1c2
[    1.808958]  [<ffffffff81003550>] ? kernel_thread_helper+0x0/0x10
[    1.809958] ---[ end trace 84b562a00a60539e ]---
Signed-off-by: NFlorian Mickler <florian@mickler.org>
Tested-by: NValdis Kletnieks <valdis.kletnieks@vt.edu>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

6c79bf0f subtracts PPPOE_SES_HLEN from mtu at
the front of ip_fragment(). So the later subtraction should be removed. The
MTU of 802.1q is also 1500, so MTU should not be changed.
Signed-off-by: NChangli Gao <xiaosuo@gmail.com>
Signed-off-by: NBart De Schuymer <bdschuym@pandora.bo>
----
 net/ipv4/ip_output.c |    6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)
Signed-off-by: NBart De Schuymer <bdschuym@pandora.bo>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initial TCP thin-stream commit did not add getsockopt support for the new
socket options: TCP_THIN_LINEAR_TIMEOUTS and TCP_THIN_DUPACK. This adds support
for them.
Signed-off-by: NJosh Hunt <johunt@akamai.com>
Tested-by: NAndreas Petlund <apetlund@simula.no>
Acked-by: NAndreas Petlund <apetlund@simula.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for running the driver on any PCI function.  Mostly this
entails replacing a constant 0 in a number of calls with the variable
function number.
Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The device supports TSO+ECN.
Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Get info about the availability of Tx on-chip queues from FW and if they
are supported set up a memory window for them.  iw_cxgb4 will be using them.
Move the existing window setup later in the init sequence, after we have
collected the new info.
Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 1704d748 ("cxgb4vf: small changes
to message processing structures/macros") was incomplete and causes cxgb4
to write bad TSO descriptors.  Fix that up by reverting the offending part
of that commit and adjusting field accesses now that they are one level
deeper.
Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The checksum provided by the device doesn't include the L3 headers,
as IPv6 expects.
Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>