Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 03 4月, 2008 4 次提交
    • M
      [POWERPC] Fix rtas_flash procfs interface · 74848398
      由 Maxim Shchetynin 提交于 
      Handling of the proc_dir_entry->count was changed in 2.6.24-rc5.
After this change, the default value for pde->count is 1 and not 0 as
before.  Therefore, if we want to check whether our procfs file is
already opened (already in use), we have to check if pde->count is
greater than 2 rather than 1.
Signed-off-by: NMaxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: NJens Osterkamp <jens@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      74848398
    • B
      [POWERPC] Fix deadlock with mmu_hash_lock in hash_page_sync · b991f05f
      由 Benjamin Herrenschmidt 提交于 
      hash_page_sync() takes and releases the low level mmu hash
lock in order to sync with other processors disposing of page
tables.  Because that lock can be needed to service hash misses
triggered by interrupt handlers, taking it must be done with
interrupts off.  However, hash_page_sync() appears to be called
with interrupts enabled, thus causing occasional deadlocks.

We fix it by making sure hash_page_sync() masks interrupts while
holding the lock.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      b991f05f
    • B
      [POWERPC] Fix iSeries hard irq enabling regression · ff3da2e0
      由 Benjamin Herrenschmidt 提交于 
      A subtle bug sneaked into iSeries recently.  On this platform, we must
not normally clear MSR:EE (the hardware external interrupt enable)
except for short periods of time.  Taking an interrupt while
soft-disabled doesn't cause us to clear it for example.

The iSeries kernel expects to mostly run with MSR:EE enabled at all
times except in a few exception entry/exit code paths.  Thus
local_irq_enable() doesn't check if it needs to hard-enable as it
expects this to be unnecessary on iSeries.

However, hard_irq_disable() _does_ cause MSR:EE to be cleared,
including on iSeries.  A call to it was recently added to the
context switch code, thus causing interrupts to become disabled
for a long periods of time, causing the iSeries watchdog to kick
in under some circumstances and other nasty things.

This patch fixes it by making local_irq_enable() properly re-enable
MSR:EE on iSeries.  It basically removes a return statement here
to make iSeries use the same code path as everybody else.  That does
mean that we might occasionally get spurious decrementer interrupts
but I don't think that matters.

Another option would have been to make hard_irq_disable() a nop
on iSeries but I didn't like it much, in case we have good reasons
to hard-disable.

Part of the patch is fixes to make sure the hard_enabled PACA field
is properly set on iSeries as it used not to be before, since it
was mostly unused.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      ff3da2e0
    • L
      [POWERPC] Fix CPM2 SCC1 clock initialization. · 025306f3
      由 Laurent Pinchart 提交于 
      A missing break statement in a switch caused cpm2_clk_setup() to initialize
SCC2 instead of SCC1.
Signed-off-by: NLaurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
      025306f3
  3. 01 4月, 2008 2 次提交
  5. 31 3月, 2008 33 次提交
  7. 30 3月, 2008 1 次提交