* since ide_hwif_t.ide_dma_{host_off,off_quietly} always return '0'
  make these functions void and while at it drop "ide_" prefix
* fix comment for __ide_dma_off_quietly()
* make __ide_dma_{host_off,off_quietly,off}() void and drop "__" prefix

v2:
* while at it rename atiixp_ide_dma_host_off() to atiixp_dma_host_off(),
  sgiioc4_ide_dma_{host_off,off_quietly}() to sgiioc4_dma_{host_off,off_quietly}()
  and sl82c105_ide_dma_off_quietly() to sl82c105_dma_off_quietly()
  [ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* add ide_set_dma() helper and make ide_hwif_t.ide_dma_check return
  -1 when DMA needs to be disabled (== need to call ->ide_dma_off_quietly)
   0 when DMA needs to be enabled  (== need to call ->ide_dma_on)
   1 when DMA setting shouldn't be changed
* fix IDE code to use ide_set_dma() instead if using ->ide_dma_check directly

v2:
* updated for scc_pata
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

All users of ->mmio == 1 are gone so convert ->mmio into flag.

Noticed by Alan Cox.

v2:
* updated for scc_pata
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This results in smaller/faster/simpler code and allows future optimizations.
Also remove no longer needed ide[_mm]_{inl,outl}() and ide_hwif_t.{INL,OUTL}.

v2:
* updated for scc_pata
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* add ide_use_fast_pio() helper for use by host drivers

* add DMA capability and hwif->autodma checks to ide_use_dma()

  - au1xxx-ide/it8213/it821x drivers didn't check for (id->capability & 1)

    [ for the IT8211/2 in SMART mode this check shouldn't be made but since
      in it821x_fixups() we set DMA bit explicitly:

               if(strstr(id->model, "Integrated Technology Express")) {
                       /* In raid mode the ident block is slightly buggy
                          We need to set the bits so that the IDE layer knows
                          LBA28. LBA48 and DMA ar valid */
                       id->capability |= 3;            /* LBA28, DMA */

       we are better off using generic helper if we can ]

  - ide-cris driver didn't set ->autodma

    [ before the patch hwif->autodma was only checked in the chipset specific
      hwif->ide_dma_check implementations, for ide-cris it is cris_dma_check()
      function so there no behavior change here ]

v2:
* updated patch description (thanks to Alan Cox for the feedback)

v3:
* updated for scc_pata driver
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This field is no longer used by the core IDE code so fix ide-{disk,floppy}
drivers to keep openers count in the driver specific objects and remove
it from ide-{cd,scsi,tape} drivers (it was write-only).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

patch 2/2:
  Remove clearing bmdma status from cdrom_decode_status() since ATA devices
  might need it as well.

  (http://lkml.org/lkml/2006/12/4/201 and http://lkml.org/lkml/2006/11/15/94)
Signed-off-by: NAlbert Lee <albertcc@tw.ibm.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: "Adam W. Hawks" <awhawks@us.ibm.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

patch 1/2 (revised):
- Fix drive->waiting_for_dma to work with CDB-intr devices.
- Do the dma status clearing in ide_intr() and add a new
  hwif->ide_dma_clear_irq for Intel ICHx controllers.

Revised per Alan, Sergei and Bart's advice.

Patch against 2.6.20-rc6. Tested ok on my ICH4 and pdc20275 adapters.
Please review/apply, thanks.
Signed-off-by: NAlbert Lee <albertcc@tw.ibm.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: "Adam W. Hawks" <awhawks@us.ibm.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Simplify the memory management and code a bit by representing acls with an
array instead of a linked list.
Signed-off-by: NJ. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix kernel-doc warnings in IRQ management.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Now that disable_irq() defaults to delayed-disable semantics, the IRQ_DISABLED
flag is not needed anymore.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Cleanup and re-enable vsyscall gettimeofday using the generic clocksource
infrastructure.

[akpm@osdl.org: cleanup]
Signed-off-by: NJohn Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch converts x86_64 to use the GENERIC_TIME infrastructure and adds
clocksource structures for both TSC and HPET (ACPI PM is shared w/ i386).

[akpm@osdl.org: fix printk timestamps]
[akpm@osdl.org: fix printk ckeanups]
[akpm@osdl.org: hpet build fix]
Signed-off-by: NJohn Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In preparation for the x86_64 generic time conversion, this patch splits out
TSC and HPET related code from arch/x86_64/kernel/time.c into respective
hpet.c and tsc.c files.

[akpm@osdl.org: fix printk timestamps]
[akpm@osdl.org: cleanup]
Signed-off-by: NJohn Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In preparation for supporting generic timekeeping, this patch cleans up
x86-64's use of vxtime.hpet_address, changing it to just hpet_address as is
also used in i386.  This is necessary since the vxtime structure will be going
away.
Signed-off-by: NJohn Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Provides generic infrastructure for vsyscall-gtod.

[akpm@osdl.org: cleanup]
Signed-off-by: NJohn Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add SysRq-Q to print pending timers and other timer info.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

add /proc/timer_list, which prints all currently pending (high-res) timers,
all clock-event sources and their parameters in a human-readable form.

Sample output:

Timer List Version: v0.1
HRTIMER_MAX_CLOCK_BASES: 2
now at 4246046273872 nsecs

cpu: 0
 clock 0:
  .index:      0
  .resolution: 1 nsecs
  .get_time:   ktime_get_real
  .offset:     1273998312645738432 nsecs
active timers:
 clock 1:
  .index:      1
  .resolution: 1 nsecs
  .get_time:   ktime_get
  .offset:     0 nsecs
active timers:
 #0: <f5a90ec8>, hrtimer_sched_tick, hrtimer_stop_sched_tick, swapper/0
 # expires at 4246432689566 nsecs [in 386415694 nsecs]
 #1: <f5a90ec8>, hrtimer_wakeup, do_nanosleep, pcscd/2050
 # expires at 4247018194689 nsecs [in 971920817 nsecs]
 #2: <f5a90ec8>, hrtimer_wakeup, do_nanosleep, irqbalance/1909
 # expires at 4247351358392 nsecs [in 1305084520 nsecs]
 #3: <f5a90ec8>, hrtimer_wakeup, do_nanosleep, crond/2157
 # expires at 4249097614968 nsecs [in 3051341096 nsecs]
 #4: <f5a90ec8>, it_real_fn, do_setitimer, syslogd/1888
 # expires at 4251329900926 nsecs [in 5283627054 nsecs]
  .expires_next   : 4246432689566 nsecs
  .hres_active    : 1
  .check_clocks   : 0
  .nr_events      : 31306
  .idle_tick      : 4246020791890 nsecs
  .tick_stopped   : 1
  .idle_jiffies   : 986504
  .idle_calls     : 40700
  .idle_sleeps    : 36014
  .idle_entrytime : 4246019418883 nsecs
  .idle_sleeptime : 4178181972709 nsecs

cpu: 1
 clock 0:
  .index:      0
  .resolution: 1 nsecs
  .get_time:   ktime_get_real
  .offset:     1273998312645738432 nsecs
active timers:
 clock 1:
  .index:      1
  .resolution: 1 nsecs
  .get_time:   ktime_get
  .offset:     0 nsecs
active timers:
 #0: <f5a90ec8>, hrtimer_sched_tick, hrtimer_restart_sched_tick, swapper/0
 # expires at 4246050084568 nsecs [in 3810696 nsecs]
 #1: <f5a90ec8>, hrtimer_wakeup, do_nanosleep, atd/2227
 # expires at 4261010635003 nsecs [in 14964361131 nsecs]
 #2: <f5a90ec8>, hrtimer_wakeup, do_nanosleep, smartd/2332
 # expires at 5469485798970 nsecs [in 1223439525098 nsecs]
  .expires_next   : 4246050084568 nsecs
  .hres_active    : 1
  .check_clocks   : 0
  .nr_events      : 24043
  .idle_tick      : 4246046084568 nsecs
  .tick_stopped   : 0
  .idle_jiffies   : 986510
  .idle_calls     : 26360
  .idle_sleeps    : 22551
  .idle_entrytime : 4246043874339 nsecs
  .idle_sleeptime : 4170763761184 nsecs

tick_broadcast_mask: 00000003
event_broadcast_mask: 00000001

CPU#0's local event device:

Clock Event Device: lapic
 capabilities:   0000000e
 max_delta_ns:   807385544
 min_delta_ns:   1443
 mult:           44624025
 shift:          32
 set_next_event: lapic_next_event
 set_mode:       lapic_timer_setup
 event_handler:  hrtimer_interrupt
  .installed:  1
  .expires:    4246432689566 nsecs

CPU#1's local event device:

Clock Event Device: lapic
 capabilities:   0000000e
 max_delta_ns:   807385544
 min_delta_ns:   1443
 mult:           44624025
 shift:          32
 set_next_event: lapic_next_event
 set_mode:       lapic_timer_setup
 event_handler:  hrtimer_interrupt
  .installed:  1
  .expires:    4246050084568 nsecs

Clock Event Device: hpet
 capabilities:   00000007
 max_delta_ns:   2147483647
 min_delta_ns:   3352
 mult:           61496110
 shift:          32
 set_next_event: hpet_next_event
 set_mode:       hpet_set_mode
 event_handler:  handle_nextevt_broadcast
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add /proc/timer_stats support: debugging feature to profile timer expiration.
Both the starting site, process/PID and the expiration function is captured.
This allows the quick identification of timer event sources in a system.

Sample output:

# echo 1 > /proc/timer_stats
# cat /proc/timer_stats
Timer Stats Version: v0.1
Sample period: 4.010 s
  24,     0 swapper          hrtimer_stop_sched_tick (hrtimer_sched_tick)
  11,     0 swapper          sk_reset_timer (tcp_delack_timer)
   6,     0 swapper          hrtimer_stop_sched_tick (hrtimer_sched_tick)
   2,     1 swapper          queue_delayed_work_on (delayed_work_timer_fn)
  17,     0 swapper          hrtimer_restart_sched_tick (hrtimer_sched_tick)
   2,     1 swapper          queue_delayed_work_on (delayed_work_timer_fn)
   4,  2050 pcscd            do_nanosleep (hrtimer_wakeup)
   5,  4179 sshd             sk_reset_timer (tcp_write_timer)
   4,  2248 yum-updatesd     schedule_timeout (process_timeout)
  18,     0 swapper          hrtimer_restart_sched_tick (hrtimer_sched_tick)
   3,     0 swapper          sk_reset_timer (tcp_delack_timer)
   1,     1 swapper          neigh_table_init_no_netlink (neigh_periodic_timer)
   2,     1 swapper          e1000_up (e1000_watchdog)
   1,     1 init             schedule_timeout (process_timeout)
100 total events, 25.24 events/sec

[ cleanups and hrtimers support from Thomas Gleixner <tglx@linutronix.de> ]
[bunk@stusta.de: nr_entries can become static]
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Implement high resolution timers on top of the hrtimers infrastructure and the
clockevents / tick-management framework.  This provides accurate timers for
all hrtimer subsystem users.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The local apic timer calibration has two problem cases:

1.  The calibration is based on readout of the PIT/HPET timer to detect the
   wrap of the periodic tick.  It happens that a box gets stuck in the
   calibration loop due to a PIT with a broken readout function.

2.  CoreDuo boxen show a sporadic PIT runs too slow defect, which results
   in a wrong lapic calibration.  The PIT goes back to normal operation once
   the lapic timer is switched to periodic mode.

Both are existing and unfixed problems in the current upstream kernel and
prevent certain laptops and other systems from booting Linux.

Rework the code to address both problems:

- Make the calibration interrupt driven.  This removes the wait_timer_tick
  magic hackery from lapic.c and time_hpet.c.  The clockevents framework
  allows easy substitution of the global tick event handler for the
  calibration.  This is more accurate than monitoring jiffies.  At this point
  of the boot process, nothing disturbes the interrupt delivery, so the
  results are very accurate.

- Verify the calibration against the PM timer, when available by using the
  early access function.  When the measured calibration period is outside of
  an one percent window, then the lapic timer calibration is adjusted to the
  pm timer result.

- Verify the calibration by running the lapic timer with the calibration
  handler.  Disable lapic timer in case of deviation.

This also removes the "synchronization" of the local apic timer to the global
tick.  This synchronization never worked, as there is no way to synchronize
PIT(HPET) and local APIC timer.  The synchronization by waiting for the tick
just alignes the local APIC timer for the first events, but later the events
drift away due to the different clocks.  Removing the "sync" is just
randomizing the asynchronous behaviour at setup time.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: Zachary Amsden <zach@vmware.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rohit Seth <rohitseth@google.com>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add clockevent drivers for i386: lapic (local) and PIT/HPET (global).  Update
the timer IRQ to call into the PIT/HPET driver's event handler and the
lapic-timer IRQ to call into the lapic clockevent driver.  The assignement of
timer functionality is delegated to the core framework code and replaces the
compile and runtime evalution in do_timer_interrupt_hook()

Use the clockevents broadcast support and implement the lapic_broadcast
function for ACPI.

No changes to existing functionality.

[ kdump fix from Vivek Goyal <vgoyal@in.ibm.com> ]
[ fixes based on review feedback from Arjan van de Ven <arjan@infradead.org> ]
Cleanups-from: Adrian Bunk <bunk@stusta.de>
Build-fixes-from: Andrew Morton <akpm@osdl.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With Ingo Molnar <mingo@elte.hu>

Add functions to provide dynamic ticks and high resolution timers.  The code
which keeps track of jiffies and handles the long idle periods is shared
between tick based and high resolution timer based dynticks.  The dyntick
functionality can be disabled on the kernel commandline.  Provide also the
infrastructure to support high resolution timers.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With Ingo Molnar <mingo@elte.hu>

The tick-management code is the first user of the clockevents layer.  It takes
clock event devices from the clock events core and uses them to provide the
periodic tick.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Architectures register their clock event devices, in the clock events core.
Users of the clockevents core can get clock event devices for their use.  The
clockevents core code provides notification mechanisms for various clock
related management events.

This allows to control the clock event devices without the architectures
having to worry about the details of function assignment.  This is also a
preliminary for high resolution timers and dynamic ticks to allow the core
code to control the clock functionality without intrusive changes to the
architecture code.

[Fixes-by: Ingo Molnar <mingo@elte.hu>]
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The apic code is quite unstructured and missing a lot of comments.

- Restructure the code into helper functions, timer, setup/shutdown,
  interrupt and power management blocks.
- Fixup comments.
- Namespace fixups
- Inline helpers for version and is_integrated
- Combine the ack_bad_irq functions

No functional changes.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: Zachary Amsden <zach@vmware.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rohit Seth <rohitseth@google.com>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Allow early access to the power management timer by exposing the verified read
function and providing a helper function which checks the pmtmr_ioport
variable and returns either the pm timer readout or 0 in case the pm timer is
not available.

Create a new header file and replace also the ifdef'ed extern definition in
arch/i386/kernel/acpi/boot.c

This is a preperatory patch for the rework of the local apic timer
calibration.

No functional changes.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is a preperatory patch for highres/dyntick:

- replace the big #ifdef ARCH_APICTIMER_STOPS_ON_C3 hackery by functions

- remove the double switch in the power verify function (in the worst case
  we switched ipi to apic and 20usec later apic to ipi)

- keep track of the the state which stops local APIC timer
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: Len Brown <len.brown@intel.com>
Cc: <linux-acpi@vger.kernel.org>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Reintroduce ktimers feature "optimized away" by the ktimers review process:
remove the curr_timer pointer from the cpu-base and use the hrtimer state.

No functional changes.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Reintroduce ktimers feature "optimized away" by the ktimers review process:
multiple hrtimer states to enable the running of hrtimers without holding the
cpu-base-lock.

(The "optimized" rbtree hack carried only 2 states worth of information and we
need 4 for high resolution timers and dynamic ticks.)

No functional changes.

Build-fixes-from: Andrew Morton <akpm@osdl.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Improve kernel/hrtimers.c locking: use a per-CPU base with a lock to control
locking of all clocks belonging to a CPU.  This simplifies code that needs to
lock all clocks at once.  This makes life easier for high-res timers and
dyntick.

No functional changes.

[ optimization change from Andrew Morton <akpm@osdl.org> ]
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- hrtimers did not use the hrtimer_restart enum and relied on the implict
  int representation. Fix the prototypes and the functions using the enums.
- Use seperate name spaces for the enumerations
- Convert hrtimer_restart macro to inline function
- Add comments

No functional changes.

[akpm@osdl.org: fix input driver]
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

For CONFIG_NO_HZ we need to calculate the next timer wheel event based on a
given jiffie value.  Extend the existing code to allow the extra 'now'
argument.  Provide a compability function for the existing implementations to
call the function with now == jiffies.  (This also solves the racyness of the
original code vs.  jiffies changing during the iteration.)

No functional changes to existing users of this infrastructure.

[ remove WARN_ON() that triggered on s390, by Carsten Otte <cotte@de.ibm.com> ]
[ made new helper static, Adrian Bunk <bunk@stusta.de> ]
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Uninline irq_enter().  [dynticks adds more stuff to it]

No functional changes.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The Geode can safely use the TSC for highres, since:

1) Does not support frequency scaling,

2) The TSC _does_ count when the CPU is halted.  Furthermore, the Geode
   supports a mode called "suspension on halt", where Suspend mode (which
   interacts with the power management states) is entered.  TSC counting
   during suspend mode is controlled by bit 8 of the Bus Controller
   Configuration Register #0 (thanks Tom!).

3) no SMP :)

Check if "RTSC counts during suspension" and remove the requirement for
verification, so the clocksource code can safely select it as an timesource
for the highres timers subsystem.
Signed-off-by: NMarcelo Tosatti <marcelo@kvack.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The TSC needs to be verified against another clocksource.  Instead of using
hardwired assumptions of available hardware, provide a generic verification
mechanism.  The verification uses the best available clocksource and handles
the usability for high resolution timers / dynticks of the clocksource which
needs to be verified.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The clocksource code allows direct updates of the rating of a given
clocksource now.  Change TSC unstable tracking to use this interface and
remove the update callback.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Using a flag filed allows to encode more than one information into a variable.
Preparatory patch for the generic clocksource verification.

[mingo@elte.hu: convert vmitime.c to the new clocksource flag]
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>