Instead of doing two 16-bit operations for the source/destination
ports, we can do one 32-bit operation to take care both.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently skb_gro_header is used for packets which put the hardware
header in skb->data with the rest in frags.  Since the drivers that
need this optimisation all provide completely non-linear packets,
we can gain extra optimisations by only performing the frag0
optimisation for completely non-linear packets.

In particular, we can simply test frag0 (instead of skb_headlen)
to see whether the optimisation is in force.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch stores the offset/headlen in local variables as they're
used repeatedly in skb_gro_offset.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function skb_gro_header is called four times per packet which
quickly adds up at 10Gb/s.  This patch inlines it to allow better
optimisations.

Some architectures perform multiplication for page_address, which
is done by each skb_gro_header invocation.  This patch caches that
value in skb->cb to avoid the unnecessary multiplications.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gcc does a poor job at generating code for the memcpy of the frags
array in skb_gro_receive, which is the primary purpose of that
function when merging frags.  In particular, it can't utilise the
alignment information of the source and destination.  This patch
open-codes the copy so we process words instead of bytes.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's going away.  Just leave the constant "20" here so that
behavior doesn't change.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BUS_ID_SIZE is really no more, and device names are dynamically
allocated and thus can be any necessary size.

So remove the BUG check here making sure BUS_ID_SIZE is at least
as large as IFNAMSIZ.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We would like to get rid of netdev->trans_start = jiffies; that about all net
drivers have to use in their start_xmit() function, and use txq->trans_start
instead.

This can be done generically in core network, as suggested by David.

Some devices, (particularly loopback) dont need trans_start update, because
they dont have transmit watchdog. We could add a new device flag, or rely
on fact that txq->tran_start can be updated is txq->xmit_lock_owner is
different than -1. Use a helper function to hide our choice.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Right-shifts of signed integers are implementation-defined so unportable.

With feedback from: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All drivers are already converted to new net_device_ops API
and nobody uses old API anymore.
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hi:

skbuff: Copy csum instead of csum_start/csum_offset

It's easier to copy the u32 csum instead of its two u16
constituents.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Cheers,
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hi:

skbuff: Move new __skb_clone code into __copy_skb_header

It seems that people just keep on adding stuff to __skb_clone
instead __copy_skb_header.  This is wrong as it means your brand-new
attributes won't always get copied as you intended.

This patch moves them to the right place, and adds a comment to
prevent this from happening again.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Thanks,
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch moves some utility functions from mac80211 to cfg80211.
Because these functions are doing generic 802.11 operations so they
are not mac80211 specific. The moving allows some fullmac drivers
to be also benefit from these utility functions.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NSamuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

My first patch submission used 200ms, which I then somehow
managed to revert back to the earlier 50ms I had used for
some tests in the second patch submission -- but that was
wrong, I should have used 200ms here. Correct that.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In "mac80211: split out and decrease probe wait time" I tried
to reduce the time waiting for a probe response, but failed to
take into account the case where we are detecting beacon loss
in software -- in that case we still wait the monitoring time
rather than the probe wait time. Fix this by refactoring the
mod_timer() calls in ieee80211_associated().
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The requirement for wireless stats to be atomic is now mostly
artificial since we hold the rtnl _and_ the dev_base_lock for
iterating the device list. Doing that is not required, just the
rtnl is sufficient (and the rtnl is required for other reasons
outlined in commit "wext: fix get_wireless_stats locking").

This will fix http://bugzilla.kernel.org/show_bug.cgi?id=13344
and make things easier for drivers.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sinec the TCPv6 GRO functions are used in the same file where
they are defined, we do not need to export them.  This was a
cut-n-paste from the IPv4 code which does need to export them.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reproted by Stephen Rothwell.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use genl_register_family_with_ops() instead of a copy.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use genl_register_family_with_ops() instead of a copy. This fixes genetlink
family leak on error path.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use genl_register_family_with_ops() instead of a copy.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use genl_register_family_with_ops() instead of a copy. This also changes
netlink related variable names to be kernel-wide unique for consistency
with other users.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use genl_register_family_with_ops() instead of a copy.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Cc: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This introduces genl_register_family_with_ops() that registers a genetlink
family along with operations from a table. This is used to kill copy'n'paste
occurrences in following patches.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Patch to add the ability to detect drops in hardware interfaces via dropwatch.
Adds a tracepoint to net_rx_action to signal everytime a napi instance is
polled.  The dropmon code then periodically checks to see if the rx_frames
counter has changed, and if so, adds a drop notification to the netlink
protocol, using the reserved all-0's vector to indicate the drop location was in
hardware, rather than somewhere in the code.
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>

 include/linux/net_dropmon.h |    8 ++
 include/trace/napi.h        |   11 +++
 net/core/dev.c              |    5 +
 net/core/drop_monitor.c     |  124 ++++++++++++++++++++++++++++++++++++++++++--
 net/core/net-traces.c       |    4 +
 net/core/netpoll.c          |    2
 6 files changed, 149 insertions(+), 5 deletions(-)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rxrpc_alloc_connection() doesn't return an error code on failure, it just
returns NULL.  IS_ERR(NULL) is false.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It seems we can fix this by disabling preemption while we re-balance the 
trie. This is with the CONFIG_CLASSIC_RCU. It's been stress-tested at high 
loads continuesly taking a full BGP table up/down via iproute -batch.

Note. fib_trie is not updated for CONFIG_PREEMPT_RCU

Reported-by: Andrei Popa
Signed-off-by: NRobert Olsson <robert.olsson@its.uu.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The the PACKET_ADD_MEMBERSHIP and the PACKET_DROP_MEMBERSHIP setsockopt
calls for af_packet already has all of the infrastructure needed to subscribe
to multiple mac addresses.  All that is missing is a flag to say that
the address we want to listen on is a unicast address.

So introduce PACKET_MR_UNICAST and wire it up to dev_unicast_add and
dev_unicast_delete.

Additionally I noticed that errors from dev_mc_add were not propagated
from packet_dev_mc so fix that.
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The net_ns_init code can be simplified. No need to save error code
if it is only going to panic if it is set 4 lines later.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Acked-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Acked-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

typo -- pkt_dev->nflows is for stats only, the number of concurrent
flows is stored in cflows.
Reported-By: NVladimir Ivashchenko <hazard@francoudi.com>
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The use of unspecified protocol in IPv6 initial route prevents quagga to
install IPv6 default route:
# show ipv6 route
S   ::/0 [1/0] via fe80::1, eth1_0
K>* ::/0 is directly connected, lo, rej
C>* ::1/128 is directly connected, lo
C>* fe80::/64 is directly connected, eth1_0

# ip -6 route
fe80::/64 dev eth1_0  proto kernel  metric 256  mtu 1500 advmss 1440
hoplimit -1
ff00::/8 dev eth1_0  metric 256  mtu 1500 advmss 1440 hoplimit -1
unreachable default dev lo  proto none  metric -1  error -101 hoplimit 255

The attached patch ensures RTPROT_KERNEL to the default initial route
and fixes the problem for quagga.
This is similar to "ipv6: protocol for address routes"
f410a1fb.

# show ipv6 route
S>* ::/0 [1/0] via fe80::1, eth1_0
C>* ::1/128 is directly connected, lo
C>* fe80::/64 is directly connected, eth1_0

# ip -6 route
fe80::/64 dev eth1_0  proto kernel  metric 256  mtu 1500 advmss 1440
hoplimit -1
fe80::/64 dev eth1_0  proto kernel  metric 256  mtu 1500 advmss 1440
hoplimit -1
ff00::/8 dev eth1_0  metric 256  mtu 1500 advmss 1440 hoplimit -1
default via fe80::1 dev eth1_0  proto zebra  metric 1024  mtu 1500
advmss 1440 hoplimit -1
unreachable default dev lo  proto kernel  metric -1  error -101 hoplimit 255
Signed-off-by: NJean-Mickael Guerin <jean-mickael.guerin@6wind.com>
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The netlink message header (struct nlmsghdr) is an unused parameter in
fill method of fib_rules_ops struct.  This patch removes this
parameter from this method and fixes the places where this method is
called.

(include/net/fib_rules.h)
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Alexander V. Lukyanov found a regression in 2.6.29 and made a complete
analysis found in http://bugzilla.kernel.org/show_bug.cgi?id=13339
Quoted here because its a perfect one :

begin_of_quotation
 2.6.29 patch has introduced flexible route cache rebuilding. Unfortunately the
 patch has at least one critical flaw, and another problem.

 rt_intern_hash calculates rthi pointer, which is later used for new entry
 insertion. The same loop calculates cand pointer which is used to clean the
 list. If the pointers are the same, rtable leak occurs, as first the cand is
 removed then the new entry is appended to it.

 This leak leads to unregister_netdevice problem (usage count > 0).

 Another problem of the patch is that it tries to insert the entries in certain
 order, to facilitate counting of entries distinct by all but QoS parameters.
 Unfortunately, referencing an existing rtable entry moves it to list beginning,
 to speed up further lookups, so the carefully built order is destroyed.

 For the first problem the simplest patch it to set rthi=0 when rthi==cand, but
 it will also destroy the ordering.
end_of_quotation

Problematic commit is 1080d709
(net: implement emergency route cache rebulds when gc_elasticity is exceeded)

Trying to keep dst_entries ordered is too complex and breaks the fact that
order should depend on the frequency of use for garbage collection.

A possible fix is to make rt_intern_hash() simpler, and only makes
rt_check_expire() a litle bit smarter, being able to cope with an arbitrary
entries order. The added loop is running on cache hot data, while cpu
is prefetching next object, so should be unnoticied.
Reported-and-analyzed-by: NAlexander V. Lukyanov <lav@yar.ru>
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rt_check_expire() computes average and standard deviation of chain lengths,
but not correclty reset length to 0 at beginning of each chain.
This probably gives overflows for sum2 (and sum) on loaded machines instead
of meaningful results.
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, we will ask the driver to configure right away
when somebody changes the desired BSSID. That's totally
strange because then we will configure the driver without
even knowing whether the BSS exists. Change this to only
configure the BSSID when associated, and configure a zero
BSSID when not associated.

As a side effect, this fixes an issue with the iwlwifi
driver which doesn't implement sta_notify properly and
uses the BSSID instead and gets very confused if the
BSSID is cleared before we disassociate, which results
in the warning Marcel posted [1] and iwlwifi bug 1995 [2].

[1] http://thread.gmane.org/gmane.linux.kernel.wireless.general/32598
[2] http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1995

Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Device drivers using wiphy_apply_custom_regulatory() want some
regulatory settings applied to their wiphy, if no bands were
configured on the wiphy then something went wrong.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When I fixed the crypto bit I must have done the negative
test only -- it is quite clearly impossible to find _any_
IBSS to join with the parameters put the wrong way around.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the genIE hasn't changed there's no reason to kick
the state machine since it won't be able to do anything
new -- doing this decreases the useless work we do for
reassociating because if we do kick the state machine
it will try to find a usable BSS but there might not be
one because wpa_supplicant will only change the BSSID
a little later.

In a sense this is a workaround for userspace behaviour,
but on the other hand userspace cannot really keep track
of what the kernel currently has for genIE since any
process could have changed that while wpa_supplicant
wasn't looking.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When updating the duration field for TX frames, skip the update for
PS-Poll frames that use this field for other purposes (AID).
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>