Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

We can skip conservative PIO "downgrade" (PIO3 becomes PIO2 etc.) on PMAC.

Problem reported by Mikael.

Cc: Mikael Pettersson <mikpe@it.uu.se>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ide_device_add() helper and convert host drivers to use it
  instead of open-coded variants.

* Make ide_pci_setup_ports() and do_ide_setup_pci_device()
  take 'u8 *idx' argument instead of 'ata_index_t *index'.

* Remove no longer needed ata_index_t.

* Unexport probe_hwif_init() and make it static.

* Unexport ide_proc_register_port().

There should be no functionality changes caused by this patch
(sgiioc4.c: ide_proc_register_port() requires hwif->present
 to be set and it won't be set if probe_hwif_init() fails).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add IDE_HFLAG_NO_ATAPI_DMA host flag and set it in host drivers which
don't support ATAPI DMA.  Then remove no longer needed hwif->atapi_dma.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* hpt34x.c: disable DMA masks for HPT345
  (hwif->autodma is zero so DMA won't be enabled anyway).

* trm290.c: disable IDE_HFLAG_TRUST_BIOS_FOR_DMA flag
  (hwif->autodma is zero so DMA won't be enabled anyway).

* Check noautodma global variable instead of drive->autodma in ide_tune_dma().

  This fixes handling of "ide=nodma" kernel parameter for icside, ide-cris,
  au1xxx-ide, pmac, it821x, jmicron, sgiioc4 and siimage host drivers.

* Remove hwif->autodma (it was not checked by IDE core code anyway) and
  drive->autodma (was set by all host drivers - except HPT345/TRM290 special
  cases - unless "ide=nodma" was used).

While at it:
- remove needless printk() from icside.c
- remove stale FIXME/comment from ide-probe.c
- don't force DMA off if PCI bus-mastering had to be enabled in setup-pci.c
  (this setting was always later over-ridden by host drivers anyway)
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

While at it:
- make struct pci_device_id tables const
- use PCI_DEVICE_ID_ITE_8213 define in it8213.c
- fix comment in generic.c
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_HFLAG_TRUST_BIOS_FOR_DMA host flag for host drivers that depend
  on BIOS for programming device/controller for DMA.  Set it in cy82c693,
  generic, ns87415, opti621 and trm290 host drivers.

* Add IDE_HFLAG_VDMA host flag for host drivers using VDMA.  Set it in cs5520
  host driver.

* Teach ide_tune_dma() about IDE_HFLAG_TRUST_BIOS_FOR_DMA flag.

* Add generic ide_dma_check() helper and remove all open coded ->ide_dma_check
  implementations.  Fix all places checking for presence of ->ide_dma_check
  hook to check for ->ide_dma_on instead.

* Remove no longer needed code from config_drive_for_dma().

* Make ide_tune_dma() static.

v2:
* Fix config_drive_for_dma() return values.

* Fix ide-dma.c build for CONFIG_BLK_DEV_IDEDMA_PCI=n by adding
  dummy config_drive_for_dma() inline.

* Fix IDE_HFLAG_TRUST_BIOS_FOR_DMA handling in ide_dma_check().

* Fix init_hwif_it8213() comment.

There should be no functionality changes caused by this patch.

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Since ide-pmac allows separate PIO and DMA timings, and ide-pmac always sets
->autotune this change shouldn't have any other effect than bringing ide-pmac
driver in-line with other host drivers wrt ->ide_dma_check implementation.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

* Convert {ide_hwif_t,ide_pci_device_t}->host_flag to be u16.

* Add IDE_HFLAG_POST_SET_MODE host flag to indicate the need to program 
  the host for the transfer mode after programming the device.  Set it
  in au1xxx-ide, amd74xx, cs5530, cs5535, pdc202xx_new, sc1200, pmac
  and via82cxxx host drivers.

* Add IDE_HFLAG_NO_SET_MODE host flag to indicate the need to completely
  skip programming of host/device for the transfer mode ("smart" hosts).
  Set it in it821x host driver and check it in ide_tune_dma().

* Add ide_set_pio_mode()/ide_set_dma_mode() helpers and convert all
  direct ->set_pio_mode/->speedproc users to use these helpers.

* Move ide_config_drive_speed() calls from ->set_pio_mode/->speedproc
  methods to callers.

* Rename ->speedproc method to ->set_dma_mode, make it void and update
  all implementations accordingly.

* Update ide_set_xfer_rate() comments.

* Unexport ide_config_drive_speed().

v2:
* Fix issues noticed by Sergei:
  - export ide_set_dma_mode() instead of moving ->set_pio_mode abuse wrt
    to setting DMA modes from sc1200_set_pio_mode() to do_special()
  - check IDE_HFLAG_NO_SET_MODE in ide_tune_dma()
  - check for (hwif->set_pio_mode) == NULL in ide_set_pio_mode()
  - check for (hwif->set_dma_mode) == NULL in ide_set_dma_mode()
  - return -1 from ide_set_{pio,dma}_mode() if ->set_{pio,dma}_mode == NULL
  - don't set ->set_{pio,dma}_mode on it821x in "smart" mode
  - fix build problem in pmac.c
  - minor fixes in au1xxx-ide.c/cs5530.c/siimage.c
  - improve patch description

Changes in behavior caused by this patch:
- HDIO_SET_PIO_MODE ioctl would now return -ENOSYS for attempts to change
  PIO mode if it821x controller is in "smart" mode
- removal of two debugging printk-s (from cs5530.c and sc1200.c)
- transfer modes 0x00-0x07 passed from user space may be programmed twice on
  the device (not really an issue since 0x00 is not supported correctly by
  any host driver ATM, 0x01 is not supported at all and 0x02-0x07 are invalid)
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add missing initialization of hwif->autodma and drive->autodma to
  pmac_ide_setup_dma().

* Use ide_tune_dma() in pmac_ide_dma_check().

While at it:

* Fix pmac_ide_dma_check() return value if DMA mode is not programmed
  (should be "-1" otherwise ide_set_dma() will try to enable DMA).

* Remove unnecessary drive->using_dma fiddling (->dma_off_quietly is always
  called before ide_set_dma() call and ide_set_dma() calls ->ide_dma_on if
  ->ide_dma_check returns "0").

v2:
* No reason to blacklist all ide_floppy devices and the old code was always
  enabling DMA anyway (without even programming controller/device if the
  device was ide_floppy).

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Use ide_config_drive_speed() instead of pmac_ide_do_setfeature() and remove
the latter, also  ide-iops.c::__ide_wait_stat() could be static again.

Since for IDE PMAC host driver IDE_CONTROL_REG is always true, device's
->quirk_list is always zero and ->ide_dma_host_{on,off} are nops than
the only changes in behavior are:

* if PIO mode is set then ->dma_off_queitly is called to disable DMA

* if setting transfer mode fails ide_dump_status() is called to dump status

v2:
* IDE PMAC controllers allow separate PIO and DMA timings and PPC userland
  depends on this fact, and calls "hdparm -p" without calling "hdparm -d".

  Therefore to compensate for DMA being disabled by ide_config_drive_speed()
  for PIO modes:

  - add IDE_HFLAG_SET_PIO_MODE_KEEP_DMA flag and set it in PMAC host driver

  - add handling of the new flag to ide-io.c::do_special()

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Upper layers are responsible for controlling nIEN so don't clear nIEN after
command execution in pmac_ide_do_setfeature().

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Use __ide_wait_stat() instead of wait_for_ready() in pmac_ide_do_setfeature().

While at it do following changes to match __ide_wait_stat() call in
ide_config_drive_speed():

* Wait WAIT_CMD time (20 sec) instead of 2 sec for device to clear BUSY_STAT.

* Check DRQ_STAT bit (shouldn't be set for good device status).

Also remove no longer needed wait_for_ready() from ide-iops.c.
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Don't check for good device status before executing the command in
pmac_ide_do_setfeature() (ide_config_drive_speed() doesn't do this).

It is a job of upper layers to guarantee that the device is ready to
accept new command before we get here.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Fix pmac_ide_dma_check() to use pmac_ide_tune_chipset() and remove no longer
  necessary pmac_ide_{m,u}dma_enable().

* While at it remove some dead code from pmac_ide_dma_check() (leftovers from
  conversion to use ide_max_dma_mode()).

There should be no functionality changes caused by this patch.

v2:
* Fix compile by replacing "id" with "drive->id" in pmac_ide_dma_check()
  (Noticed by Ben).

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

pmac_ide_do_setfeature() contains matching nIEN setting/clearing so this
Device Control register messing in pmac_ide_dma_check() is totally unnecessary.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Move adjusting of cycle time for devices providing explicit DMA cycle time
  from pmac_ide_mdma_enable() to set_timings_mdma().

* Remove no longer needed drive_cycle_time argument.

* BUG() if unsupported speed argument value is passed (shouldn't happen).

* Matching access/recovery timings always exist so remove redundant check.

* Make set_timings_mdma() void.

* Update pmac_ide_tune_chipset()'s comment.
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Don't check check for pmif == NULL (it should never be NULL if we got here).

* Make a local copy of the timings and set the pmif->timings[] only after
  setting the transfer mode on the device (otherwise SELECT_DRIVE() call in
  pmac_ide_do_setfeature() will program new timings before the transfer mode
  is set on the device - this was pointed out by Sergei).  This change makes
  pmac_ide_tune_chipset() behavior match this of pmac_ide_{m,u}dma_enable().
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

kauai_lookup_timing() should always return non-zero return value:

* BUG() in kauai_lookup_timing() if the timing info cannot be found.

* Remove code checking for zero return value from all callers.
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Use ->set_pio_mode method to program PIO modes in ide_set_xfer_rate()
(the only place which used ->speedproc to program PIO modes) and remove
handling of PIO modes from all ->speedproc implementations.

v2:
* Fix pmac_ide_tune_chipset() comment.

There should be no functionality changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add { 0, 0 } entry to {kauai,shasta}_pio_timings[] so kauai_lookup_timing()
  always returns a valid PIO timing (fixes PIO timing not being set for devices
  with minimum PIO cycle <= 120ns).

* Add setting transfer mode on the device to pmac_ide_set_pio_mode().

* Fix pmac_ide_set_pio() to always program chipset for given PIO timing instead
  of only when the device we want to program PIO timing for is the currently
  selected one.

* Now that pmac_ide_set_pio() is fixed there is no need to set transfer mode
  on the device and program chipset for PIO in pmac_ide_tune_chipset()
  (returning 0 == success is not entirely correct but is OK for now since
  the upper layers are only checking ->speedproc return value for DMA modes).

v2:
* s/speed/XFER_PIO_0 + pio/ in pmac_ide_set_pio_mode() so it actually compiles.

* Removal of kauai_lookup_timing() return value checking went to separate patch.

v3:
* Use XFER_PIO_0 not XFER_PIO. (Noticed by Ben)

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags
  and set them in ht6560, cmd640, cmd64x and sc1200 host drivers.

* Add set_pio_mode_abuse() for checking if host driver has a non-standard
  ->tuneproc() implementation and use it in do_special().

* Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find
  the maximum PIO mode supported by the host), also add ide_set_max_pio()
  wrapper for ide_set_pio() to use for auto-tuning.  Convert users of
  ->tuneproc to use ide_set{_max}_pio() where possible.  This leaves only
  do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as
  a direct users of ->tuneproc.

* Remove no longer needed ide_get_best_pio_mode() calls and printk-s
  reporting PIO mode selected from ->tuneproc implementations.

* Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const.

* Remove stale comment from ide_config_drive_speed().

v2:
* Fix "ata_" prefix (Noticed by Jeff).

v3:
* Minor cleanups/fixups per Sergei's suggestions.

v4:
* Fix compile problem in drivers/ide/pci/cmd640.c
  (Noticed by Andrew Morton).

* Improve some ->set_pio_mode comments.
Reviewed-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Move ide_rate_filter() calls from host drivers to IDE core.

* Make ide_rate_filter() static.

* Make 'speed' argument of ->speedproc const.

v2:
* Fix it8213_tune_chipset() comment.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Fix icside, cris-ide, au1xxx-ide, amd74xx, via82cxxx and pmac host drivers
  to use ide_rate_filter().

  This results in the following modes (from user requests) being clipped down:
  - invalid modes (values 0x46-0xFF)  [ for all hosts ]
  - unsupported by a host UDMA modes  [ for hosts which support UDMA]
  - all UDMA modes and MWDMA3-4 modes [ for hosts which don't support UDMA ]
  - invalid modes (values 0x25-0x39)  [ for hosts which don't support UDMA ]

* Host driver specific changes in behavior:

  icside:
    - no change

  cris-ide
    - clip unsupported UDMA3-6 modes down
    - fix BUG() on trying to set unsupported UDMA3-6 modes

  au1xxx-ide/pmac
    - clip unsupported UDMA modes down

  amd74xx/via82cxxx
    - clip unsupported UDMA modes down
    - fix random PIO timings being set for unsupported/invalid modes
    - fix unsupported/invalid modes being set on the device

* While at it remove no longer needed checks from pmac.c driver.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The PCI device table in the powermac IDE driver isn't properly
terminated.  Depending on how your kernel is linked and other random
factors, you can end up with this driver matched against any other PCI
device in your system, possibly crashing at boot.

Thanks to Heikki for tracking this down with me, the bug have been there
for some time, though it rarely hurts due to luck.  In this case, the
switch from .22 to .23-rc9 is causing it to show up due to differences
in the resulting layout of .data I suppose.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <pmac@au1.ibm.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Heikki Lindholm <holindho@cs.helsinki.fi>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Removes these warnings:

/home/sfr/kernels/linus/drivers/ide/ppc/pmac.c: In function 'pmac_ide_dma_check':
/home/sfr/kernels/linus/drivers/ide/ppc/pmac.c:1807: warning: unused variable 'map'
/home/sfr/kernels/linus/drivers/ide/ppc/pmac.c:1805: warning: unused variable 'pmif'
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Cc: paulus@samba.org
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

pmac_ide_tune_chipset() don't set drive->init_speed.

Fix it by setting drive->{current,init}_speed in pmac_ide_do_setfeature()
and clean up pmac_ide_{tune_chipset,mdma_enable,udma_enable}().
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ATA_PIO[0-6] defines to <linux/ata.h>.

* Add ->pio_mask field to ide_pci_device_t and ide_hwif_t.

* Add PIO masks to host drivers.

<linux/ata.h> change ACK-ed by Jeff Garzik <jeff@garzik.org>.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Drop no longer needed "PIO data" argument from ide_get_best_pio_mode()
  and convert all users accordingly.

* Remove no longer needed ide_pio_data_t.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ide_pio_cycle_time() helper.

* Use it in ali14xx/ht6560b/qd65xx/cmd64{0,x}/sl82c105 and pmac host drivers
  (previously cycle time given by the device was only used for "pio" == 255).

* Remove no longer needed ide_pio_data_t.cycle_time field.

v2:
* Fix "ata_" prefix (Noticed by Jeff).
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This patch allows users to override both host and device side cable detection
with "ideX=ata66" kernel parameter.  Thanks to this it should be now possible
to use UDMA > 2 modes on systems (laptops mainly) which use short 40-pin cable
instead of 80-pin one.

Next patches add automatic detection of some systems using short cables.

Changes:

* Rename hwif->udma_four to hwif->cbl and make it u8.

* Convert all existing users accordingly (use ATA_CBL_* defines while at it).  

* Add ATA_CBL_PATA40_SHORT support to ide-iops.c:eighty_ninty_three().

* Use ATA_CBL_PATA40_SHORT for "ideX=ata66" kernel parameter.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>

ide-timing.h:

* remove handling of DMA modes from ide_find_best_mode() and rename it to
  ide_find_best_pio_mode()

* drop no longer needed "map" argument from ide_find_best_pio_mode()
  and delete needless ->id check

* remove no longer needed XFER_SWDMA and XFER_UDMA* defines

au1xxx-ide.c:

* use ide_max_dma_mode() instead of ide_find_best_mode()

* remove needless CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA #ifdef

amd74xx.c:

* store UDMA masks in amd_ide_chip[] and while at it make "base" field
  to be u8 instead of unsigned long

* convert the driver to use UDMA masks from amd_ide_chip[]

* use ide_max_dma_mode() and ide_find_best_pio_mode() instead
  of ide_find_best_mode()

* delete stale comment from amd74xx_ide_dma_check()

* remove no longer needed AMD_UDMA* defines

via82cxxx.c:

* remove unused DISPLAY_VIA_TIMINGS define

* store UDMA masks in via_isa_bridges[] and while at it make "flags" field
  to be u8 instead of u16

* convert the driver to use UDMA masks from via_isa_bridges[]

* use ide_max_dma_mode() and ide_find_best_pio_mode() instead
  of ide_find_best_mode()

* remove no longer needed VIA_UDMA* defines

pmac.c:

* use ide_max_dma_mode() instead of ide_find_best_mode()

There should be no functionality changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>

Since ide_dma_timeout() method's result is discarded, make it return 'void'.
While at it, drop 'ide_' from the method's name, drop the '__' prefix from
the default method's name, and do some cleanups in this method driver-wise:

- in ide-dma.c, au1xxx-ide.c, and pdc202xx_old.c, define/use 'hwif' variable;

- in au1xxx-ide.c, get rid of commented out printk();

- in sl82c105.c, get rid of unnecessary variables.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Since ide_dma_lostirq() method's result is discarded, make it return 'void'.
While at it, rename the method to dma_lost_irq(), drop the '__' prefix from the
default method's name, and do some cleanups in this method driver-wise:

- in aec62xx.c, rename the method in accordance with other drivers, and get rid
  of unnecessary variables there;

- in pdc202xx_old.c, define/use 'hwif' variable;

- in sgiioc4.c, rearrange the code to call the resetproc() method directly.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* create_proc_ide_interfaces() tries to add /proc entries for every probed
  and initialized IDE port, replace it by ide_proc_register_port() which does
  it only for the given port (also rename destroy_proc_ide_interface() to
  ide_proc_unregister_port() for consistency)
  
* convert {create,destroy}_proc_ide_interface[s]() users to use new functions

* pmac driver depended on proc_ide_create() to add /proc port entries, fix it
  
* au1xxx-ide, swarm and cs5520 drivers depended indirectly on ide-generic
  driver (CONFIG_IDE_GENERIC=y) to add port /proc entries, fix them

* there is now no need to add /proc entries for IDE ports in proc_ide_create()
  so don't do it

* proc_ide_create() needs now to be called before drivers are probed - fix it,
  while at it make proc_ide_create() create /proc "ide" directory
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

for consistency with other Open Firmware interfaces (and Sparc).

This is just a straight replacement.

This leaves the compatibility define in place.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

These are all the remaining instances of get_property.  Simple rename of
get_property to of_get_property.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>