When interface stopped while running intensive Rx traffic, the following oops
observed:

[89846.734683] Call trace:
[89846.737117] [<ffffffc00083aa64>] dev_gro_receive+0xac/0x358
[89846.742674] [<ffffffc00083ae94>] napi_gro_receive+0x24/0xa4
[89846.748251] [<ffffffbffc1c2f88>] $x+0xec/0x1f8 [wil6210]         wil_netif_rx_any
[89846.753547] [<ffffffbffc1c4830>] $x+0x34/0x54 [wil6210]          wil_release_reorder_frame
[89846.758755] [<ffffffbffc1c48ac>] wil_release_reorder_frames+0x5c/0x78 [wil6210]
[89846.766044] [<ffffffbffc1c4bf8>] wil_tid_ampdu_rx_free+0x20/0x48 [wil6210]
[89846.772901] [<ffffffbffc1bedc8>] $x+0x190/0x1e8 [wil6210]
[89846.778285] [<ffffffbffc1c0ed4>] wmi_event_worker+0x230/0x2f8 [wil6210]
[89846.784865] [<ffffffc0000b0bc8>] process_one_work+0x278/0x3fc
[89846.790591] [<ffffffc0000b1218>] worker_thread+0x200/0x330
[89846.796060] [<ffffffc0000b6664>] kthread+0xac/0xb8
[89846.800836] Code: b940c661 f9406a62 8b010041 f9400026 (f8636882)
[89846.807008] ---[ end trace d6fdc17cd27d18f6 ]---

Reason is the following: when removing Rx vring
(wil_netdev_ops.ndo_stop -> wil_stop -> wil_down -> __wil_down -> wil_rx_fini),
Rx interrupt occurs. It trigger Rx NAPI, calling wil_rx_handle() that reaps
(already cleaned) buffer, causing skb referring to garbage memory being set into reorder buffer.
Then, network stack trying to access this buffer and fails.

Prevent Rx NAPI from being scheduled if device going to stop. Bit wil_status_napi_en reflects
NAPI enablement state, check it when triggering Rx NAPI.

Testing shows that check for wil_status_napi_en sometimes gets negative, and new error message
get printed - in this case kernel oops would be observed. Original oops is no more reproducible.

This change requires also changes in the AP flows.
Properly enable/disable NAPI for the AP. Make sure Rx VRING is disabled
when resetting target.

For this, promote __wil_up() and __wil_down() to the module scope, and use it
in the relevant flows.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To better reflect real action performed, rename:
s/wil6210_disable_irq/wil_mask_irq/
s/wil6210_enable_irq/wil_unmask_irq/
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Expose firmware limit for the max_scan_ie_len;
also do actually set IE's for the probe request

max_scan_ie_len used to be 0, this blocks scan requests with non-zero IE's
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

re-use of wmi_ready for both FW ready event and for wmi_call was causing
false "FW not ready" indication in case wmi_call() was invoked while reset
took place.
add wmi_call completion variable instead of re-using wmi_ready.
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

HW supports upto 2304 packet size on the air.
HW is responsible for adding (Tx) or removing (Rx) the following headers:
802.11 hdr: 26B
SNAP: 8B
CRC: 4B
Security (optional): 24B
HW adds max 62B to the payload passed from driver. It means driver can use
max packet size of 2304-62 = 2242B
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This allows updating IEs (e.g. from hostapd) when AP is already started
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Driver is sending connect request IEs to FW only for secure connection and
ignores them for non-secure connection.
This is fixed by always sending the IEs to FW upon connect request
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While handling Rx packet, BACK event arrives and frees tid_ampdu_rx array.
This causes kernel panic while accessing already freed spinlock

The fix is to remove tid_ampdu_rx[]'s spinlock and instead use single
sta's spinlock to guard the whole tid_ampdu_rx array.
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When WMI event received when driver not ready to accept it, the printed error
message is misleading and hints that HW is stuck. Modify the error message
to make it clearer
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This race condition was causing double free of tid_ampdu_rx structures
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When CONFIG_DYNAMIC_DEBUG is not defined, print_hex_dump_debug
is mapped directly to print_hex_dump which might cause
printout to exist all the time
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Driver disabled PCI master before making sure HW is idle.
This caused memory corruption in case HW access system memory after
PCI master got disabled.
The fix is to change uninit sequence. Make sure FW/HW is idle before
disabling PCI
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After setting interrupt handler, driver enabled interrupts.
This caused stale (old) HW interrupts to fire before driver is
fully initialized.
The fix is to enable interrupts only when driver is fully initialized
and after FW/HW reset (to prevent any stale interrupts)
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

added misc printouts in some init/uninit functions for better traceability
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

New module (wil_platform) for handling platform specific tasks
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

- parentheses, indentation, typos
- seq_puts() instead of seq_printf() with single argument
- sizeof(var) vs. sizeof(type)
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Log worker thread start/stop; as well as every handler invocation
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

when connecting, print some info about BSS
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Firmware download implemented but is still experimental feature;
flag controlling it added, no_fw_load. It is true by default,
use no_fw_load=N to activate feature.

Reset flows also got some adjustment for the fw download to work
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Scanning is curently broken when two channel contexts
are active. For example in a P2P-GO/STA setup, the
offchannel timer allows HZ / 10 to elapse before initiating
a switch to the next scan channel from the current operating
channel, which in this case would be the P2P-GO context.

But, the channel context timer might decide to switch
to the STA context when an SWBA comes early and a beacon
is sent out. Since pending offchannel requests are processed
in EVENT_BEACON_PREPARE, this causes inconsistent scanning.

Fix this by making sure that a context switch happens
before processing the pending offchannel request. This
also makes sure that active channel contexts will always
have higher priority than offchannel operations and the
scan sequence looks like this:

p2p-go, sta, p2p-go, offchannel, p2p-go, sta, p2p-go, offchannel,.....

The oper-channel is p2p-go, so the STA context has to
switch to p2p-go again before switching offchannel.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When multiple channel contexts are active, an offchannel
request will not be handled immediately, but will be
queued to be handled later. But, currently, the channel definition
is not copied to the local offchannel state. This
breaks operation like scanning when MCC is active.

Fix this by storing the offchannel parameters properly.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reduces code duplication.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, the interface count is maintained globally,
but this causes problems in RX filter calculation.
Make the interface count a per-channel-context variable
to fix this.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Maintain the RX filter on a per-channel-context
basis and not globally. Not doing so was resulting
in incorrect filter calculation.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ATH9K_RX_FILTER_COMP_BAR is used to receive BAR
completion frames and is set if the current channel
is HT. When channel contexts are enabled, instead of using
the mac80211 helpers, check if the current channel
definition is HT.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since ath_startrecv() doesn't return an error value,
cleanup the callsites.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If multiple channel contexts are active, then the opmode
can be different in each context. Since the RX filter is
calculated in ath_startrecv() before switching to the
new opmode, the wrong filters are chosen.

Fix this by calling ath9k_calculate_summary_state() before
the RX module is started.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since CTWindow can be used for improving discoverability,
fill this field in the NoA Attribute properly.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, different units are used for handling
sc->offchannel.duration. In scan mode, it contains jiffies and in RoC
mode, milliseconds is used. This causes confusion since in
ath_chanctx_switch(), TU_TO_USEC is used to determine the offchannel
duration, resulting in incorrect values. Fix this by using jiffies in
both modes.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The start time field in the NoA attribute needs to be
updated based on the TSF timer when an absence notification
is sent by the P2P GO. When two channel contexts are active,
continuous, cyclic NoA is announced by setting the count value to 255,
but the start time is updated only once, for one beacon and
the same value is sent in all subsequent beacons, even
though the timestamp keeps moving.

Fix this by removing the check for 'periodic_noa_duration'
and assign the interface's start_time/duration values directly
when there is more than one active context.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If a station interface is already assigned to a context
and is active and a second interface of type AP is added,
then beaconing on the new interface has to be begin only
after the BSS_CHANGED_BEACON_ENABLED flag is sent by mac80211
to the driver.

But, since we issue ATH_CHANCTX_EVENT_ENABLE_MULTICHANNEL as soon
as a new channel context is added, a switch occurs almost immediately
before BSS_CHANGED_BEACON_ENABLED is received. When a HW reset
is done for the new context, beacons are enabled for the
interface since "enable_beacon" in the BSS config maintained
in mac80211 is true - but the driver hasn't been notified yet.
This causes a panic, since the beacon interval is zero for this
interface and ath9k_cmn_beacon_config_ap() doesn't have a safety check.

Fix this panic by checking if the beacon params has been cached
for this context and use the "enable_beacon" flag maintained
locally in the driver. Also, recalculate the summary data
after the beacon params have been cached when BSS_CHANGED_BEACON_ENABLED
is received.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If the current opmode is managed, the ATH_OP_BEACONS flag
needs to be set only when there is a primary station interface
and it is associated/active.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In channel context mode, when a new context is added,
mac80211 issues a bss_info_changed() notfication when
preparing the connection for the new interface/context.

But, this is done prior to the mgd_prepare_tx() call which
is where we switch to the new context. Since the current
context will be different when the earlier bss_info_changed()
is handled, the beacon information for the VIF is not
updated, but discarded since the rules for the current context
disallows it.

In the subsequent association process for the new context/vif,
this becomes a problem because the beacon parameters are invalid.
This causes problems with the TSF timer, causing large jumps.

To fix this, check if the beacon info is being updated for a
different context and if so, allow it without any checks since
we limit the max. interfaces to two anyway.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJade Bilkey <herself@thefumon.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

According to RCU_INIT_POINTER()'s block comment 3.a, it can be used if
"3.   The referenced data structure has already been exposed to readers either
at compile time or via rcu_assign_pointer() -and-
 a.   You have not made -any- reader-visible changes to this structure since
then".

This case fulfills the conditions above because between the rcu_dereference()
call (cvif = rcu_dereference(ar->beacon_iter);) and the rcu_assign_pointer()
call there is no update of the "cvif" variable.
Therefore, this patch makes the replacement.

The following Coccinelle semantic patch was used:
@@
identifier v;
@@

v = rcu_dereference(...);
... when != rcu_dereference(...);
    when != v = ...;
    when != (<+...v...+>)++;
    when != \(memcpy\|memset\)(...);
(
- rcu_assign_pointer
+ RCU_INIT_POINTER
  (..., v);
|
 if(...) {
... when != v = ...;
- rcu_assign_pointer
+ RCU_INIT_POINTER
  (..., v);
... when any
 }
)

Because there are cases where between a “rcu_dereference()” call and a
“rcu_assign_pointer()” call might be updates of the value that interests us,
the Coccinelle semantic patch ignores them and replaces with
"RCU_INIT_POINTER()" only when the update is not happening.
Signed-off-by: NAndreea-Cristina Bernat <bernat.ada@gmail.com>
Acked-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Setup the channel context correctly. Not doing this was
causing beacon loss in a P2P-GO/STA concurrent setup.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>