- 17 1月, 2014 3 次提交
-
-
由 Jan Kiszka 提交于
In contrast to VMX, SVM dose not automatically transfer DR6 into the VCPU's arch.dr6. So if we face a DR6 read, we must consult a new vendor hook to obtain the current value. And as SVM now picks the DR6 state from its VMCB, we also need a set callback in order to write updates of DR6 back. Fixes a regression of 020df079. Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com> Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
由 Jan Kiszka 提交于
Whenever we change arch.dr7, we also have to call kvm_update_dr7. In case guest debugging is off, this will synchronize the new state into hardware. Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com> Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
由 Vadim Rozenfeld 提交于
Signed-off: Peter Lieven <pl@kamp.de> Signed-off: Gleb Natapov Signed-off: Vadim Rozenfeld <vrozenfe@redhat.com> After some consideration I decided to submit only Hyper-V reference counters support this time. I will submit iTSC support as a separate patch as soon as it is ready. v1 -> v2 1. mark TSC page dirty as suggested by Eric Northup <digitaleric@google.com> and Gleb 2. disable local irq when calling get_kernel_ns, as it was done by Peter Lieven <pl@amp.de> 3. move check for TSC page enable from second patch to this one. v3 -> v4 Get rid of ref counter offset. v4 -> v5 replace __copy_to_user with kvm_write_guest when updateing iTSC page. Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
- 16 1月, 2014 1 次提交
-
-
由 Paolo Bonzini 提交于
After the previous patch from Marcelo, the comment before this write became obsolete. In fact, the write is unnecessary. The calls to kvm_write_tsc ultimately result in a master clock update as soon as all TSCs agree and the master clock is re-enabled. This master clock update will rewrite tsc_timestamp. So, together with the comment, delete the dead write too. Reviewed-by: NMarcelo Tosatti <mtosatti@redhat.com> Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
- 15 1月, 2014 6 次提交
-
-
由 Marcelo Tosatti 提交于
To fix a problem related to different resolution of TSC and system clock, the offset in TSC units is approximated by delta = vcpu->hv_clock.tsc_timestamp - vcpu->last_guest_tsc (Guest TSC value at (Guest TSC value at last VM-exit) the last kvm_guest_time_update call) Delta is then later scaled using mult,shift pair found in hv_clock structure (which is correct against tsc_timestamp in that structure). However, if a frequency change is performed between these two points, this delta is measured using different TSC frequencies, but scaled using mult,shift pair for one frequency only. The end result is an incorrect delta. The bug which this code works around is not the only cause for clock backwards events. The global accumulator is still necessary, so remove the max_kernel_ns fix and rely on the global accumulator for no clock backwards events. Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com> Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
由 Marcelo Tosatti 提交于
Limit PIT timer frequency similarly to the limit applied by LAPIC timer. Cc: stable@kernel.org Reviewed-by: NJan Kiszka <jan.kiszka@siemens.com> Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com> Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
由 Marcelo Tosatti 提交于
Rom Freiman <rom@stratoscale.com> notes other code paths vulnerable to bug fixed by 989c6b34. Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
-
由 Paolo Bonzini 提交于
Merge tag 'kvm-arm-for-3.14' of git://git.linaro.org/people/christoffer.dall/linux-kvm-arm into kvm-queue
-
由 Scott Wood 提交于
Commit 7940876e ("kvm: make local functions static") broke KVM PPC builds due to removing (rather than moving) the stub version of kvm_vcpu_eligible_for_directed_yield(). This patch reintroduces it. Signed-off-by: NScott Wood <scottwood@freescale.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: Alexander Graf <agraf@suse.de> [Move the #ifdef inside the function. - Paolo] Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
由 Paul Bolle 提交于
Building vfio.o triggers a GCC warning (when building for 32 bits x86): arch/x86/kvm/../../../virt/kvm/vfio.c: In function 'kvm_vfio_set_group': arch/x86/kvm/../../../virt/kvm/vfio.c:104:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast] void __user *argp = (void __user *)arg; ^ Silence this warning by casting arg to unsigned long. argp's current type, "void __user *", is always casted to "int32_t __user *". So its type might as well be changed to "int32_t __user *". Signed-off-by: NPaul Bolle <pebolle@tiscali.nl> Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
- 09 1月, 2014 7 次提交
-
-
由 Sachin Kamat 提交于
trace.h was included twice. Remove duplicate inclusion. Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org> Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
-
由 Marc Zyngier 提交于
The THP code in KVM/ARM is a bit restrictive in not allowing a THP to be used if the VMA is not 2MB aligned. Actually, it is not so much the VMA that matters, but the associated memslot: A process can perfectly mmap a region with no particular alignment restriction, and then pass a 2MB aligned address to KVM. In this case, KVM will only use this 2MB aligned region, and will ignore the range between vma->vm_start and memslot->userspace_addr. It can also choose to place this memslot at whatever alignment it wants in the IPA space. In the end, what matters is the relative alignment of the user space and IPA mappings with respect to a 2M page. They absolutely must be the same if you want to use THP. Cc: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com> Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
-
由 Marcelo Tosatti 提交于
After free_loaded_vmcs executes, the "loaded_vmcs" structure is kfreed, and now vmx->loaded_vmcs points to a kfreed area. Subsequent free_loaded_vmcs then attempts to manipulate vmx->loaded_vmcs. Switch the order to avoid the problem. https://bugzilla.redhat.com/show_bug.cgi?id=1047892Reviewed-by: NJan Kiszka <jan.kiszka@siemens.com> Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
-
由 Chen Fan 提交于
fix the 'vcpi' typos when apic_debug is enabled. Signed-off-by: NChen Fan <chen.fan.fnst@cn.fujitsu.com> Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
-
由 Stephen Hemminger 提交于
The function kvm_io_bus_read_cookie is defined but never used in current in-tree code. Signed-off-by: NStephen Hemminger <stephen@networkplumber.org> Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
-
由 Stephen Hemminger 提交于
Running 'make namespacecheck' found lots of functions that should be declared static, since only used in one file. Signed-off-by: NStephen Hemminger <stephen@networkplumber.org> Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
-
由 Zhihui Zhang 提交于
According to Table C-1 of Intel SDM 3C, a VM exit happens on an I/O instruction when "use I/O bitmaps" VM-execution control was 0 _and_ the "unconditional I/O exiting" VM-execution control was 1. So we can't just check "unconditional I/O exiting" alone. This patch was improved by suggestion from Jan Kiszka. Reviewed-by: NJan Kiszka <jan.kiszka@siemens.com> Signed-off-by: NZhihui Zhang <zzhsuny@gmail.com> Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
-
- 01 1月, 2014 1 次提交
-
-
由 Masanari Iida 提交于
Correct spelling typo in Documentations/virtual/kvm Signed-off-by: NMasanari Iida <standby24x7@gmail.com> Acked-by: NRandy Dunlap <rdunlap@infradead.org> Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
-
- 28 12月, 2013 5 次提交
-
-
由 Marc Zyngier 提交于
-
由 Anup Patel 提交于
The SMC-based PSCI emulation for Guest is going to be very different from the in-kernel HVC-based PSCI emulation hence for now just inject undefined exception when Guest executes SMC instruction. Signed-off-by: NAnup Patel <anup.patel@linaro.org> Signed-off-by: NPranavkumar Sawargaonkar <pranavkumar@linaro.org> Signed-off-by: Nmarc Zyngier <marc.zyngier@arm.com>
-
由 Anup Patel 提交于
This patch allows us to have X-Gene guest VCPU when using KVM arm64 on APM X-Gene host. We add KVM_ARM_TARGET_XGENE_POTENZA for X-Gene Potenza compatible guest VCPU and we return KVM_ARM_TARGET_XGENE_POTENZA in kvm_target_cpu() when running on X-Gene host with Potenza core. [maz: sanitized the commit log] Signed-off-by: NAnup Patel <anup.patel@linaro.org> Signed-off-by: NPranavkumar Sawargaonkar <pranavkumar@linaro.org> Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
-
由 Anup Patel 提交于
Current max VCPUs per-Guest is set to 4 which is preventing us from creating a Guest (or VM) with 8 VCPUs on Host (e.g. X-Gene Storm SOC) with 8 Host CPUs. The correct value of max VCPUs per-Guest should be same as the max CPUs supported by GICv2 which is 8 but, increasing value of max VCPUs per-Guest can make things slower hence we add Kconfig option to let KVM users select appropriate max VCPUs per-Guest. Signed-off-by: NAnup Patel <anup.patel@linaro.org> Signed-off-by: NPranavkumar Sawargaonkar <pranavkumar@linaro.org> Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
-
由 Marc Zyngier 提交于
Merge tag 'vgic-migrate-for-marc' of git://git.linaro.org/people/christoffer.dall/linux-kvm-arm into kvm-arm64/next VGIC and timer migration pull
-
- 22 12月, 2013 13 次提交
-
-
由 Christoffer Dall 提交于
Implement support for the CPU interface register access driven by MMIO address offsets from the CPU interface base address. Useful for user space to support save/restore of the VGIC state. This commit adds support only for the same logic as the current VGIC support, and no more. For example, the active priority registers are handled as RAZ/WI, just like setting priorities on the emulated distributor. Acked-by: NMarc Zyngier <marc.zyngier@arm.com> Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
-
由 Christoffer Dall 提交于
Handle MMIO accesses to the two registers which should support both the case where the VMs want to read/write either of these registers and the case where user space reads/writes these registers to do save/restore of the VGIC state. Note that the added complexity compared to simple set/clear enable registers stems from the bookkeping of source cpu ids. It may be possible to change the underlying data structure to simplify the complexity, but since this is not in the critical path at all, this will do. Also note that reading this register from a live guest will not be accurate compared to on hardware, because some state may be living on the CPU LRs and the only way to give a consistent read would be to force stop all the VCPUs and request them to unqueu the LR state onto the distributor. Until we have an actual user of live reading this register, we can live with the difference. Acked-by: NMarc Zyngier <marc.zyngier@arm.com> Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
-
由 Christoffer Dall 提交于
To properly access the VGIC state from user space it is very unpractical to have to loop through all the LRs in all register access functions. Instead, support moving all pending state from LRs to the distributor, but leave active state LRs alone. Note that to accurately present the active and pending state to VCPUs reading these distributor registers from a live VM, we would have to stop all other VPUs than the calling VCPU and ask each CPU to unqueue their LR state onto the distributor and add fields to track active state on the distributor side as well. We don't have any users of such functionality yet and there are other inaccuracies of the GIC emulation, so don't provide accurate synchronized access to this state just yet. However, when the time comes, having this function should help. Acked-by: NMarc Zyngier <marc.zyngier@arm.com> Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
-
由 Christoffer Dall 提交于
Add infrastructure to handle distributor and cpu interface register accesses through the KVM_{GET/SET}_DEVICE_ATTR interface by adding the KVM_DEV_ARM_VGIC_GRP_DIST_REGS and KVM_DEV_ARM_VGIC_GRP_CPU_REGS groups and defining the semantics of the attr field to be the MMIO offset as specified in the GICv2 specs. Missing register accesses or other changes in individual register access functions to support save/restore of the VGIC state is added in subsequent patches. Acked-by: NMarc Zyngier <marc.zyngier@arm.com> Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
-
由 Christoffer Dall 提交于
The arch-generic KVM code expects the cpu field of a vcpu to be -1 if the vcpu is no longer assigned to a cpu. This is used for the optimized make_all_cpus_request path and will be used by the vgic code to check that no vcpus are running. Acked-by: NMarc Zyngier <marc.zyngier@arm.com> Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
-
由 Christoffer Dall 提交于
Rename the vgic_ranges array to vgic_dist_ranges to be more specific and to prepare for handling CPU interface register access as well (for save/restore of VGIC state). Pass offset from distributor or interface MMIO base to find_matching_range function instead of the physical address of the access in the VM memory map. This allows other callers unaware of the VM specifics, but with generic VGIC knowledge to reuse the function. Acked-by: NMarc Zyngier <marc.zyngier@arm.com> Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
-
由 Christoffer Dall 提交于
Define CPU interface offsets for the GICC_ABPR, GICC_APR, and GICC_IIDR registers. Define distributor registers for the GICD_SPENDSGIR and the GICD_CPENDSGIR. KVM/ARM needs to know about these definitions to fully support save/restore of the VGIC. Also define some masks and shifts for the various GICH_VMCR fields. Cc: Thomas Gleixner <tglx@linutronix.de> Acked-by: NMarc Zyngier <marc.zyngier@arm.com> Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
-
由 Christoffer Dall 提交于
Support setting the distributor and cpu interface base addresses in the VM physical address space through the KVM_{SET,GET}_DEVICE_ATTR API in addition to the ARM specific API. This has the added benefit of being able to share more code in user space and do things in a uniform manner. Also deprecate the older API at the same time, but backwards compatibility will be maintained. Acked-by: NMarc Zyngier <marc.zyngier@arm.com> Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
-
由 Christoffer Dall 提交于
Support creating the ARM VGIC device through the KVM_CREATE_DEVICE ioctl, which can then later be leveraged to use the KVM_{GET/SET}_DEVICE_ATTR, which is useful both for setting addresses in a more generic API than the ARM-specific one and is useful for save/restore of VGIC state. Adds KVM_CAP_DEVICE_CTRL to ARM capabilities. Note that we change the check for creating a VGIC from bailing out if any VCPUs were created, to bailing out if any VCPUs were ever run. This is an important distinction that shouldn't break anything, but allows creating the VGIC after the VCPUs have been created. Acked-by: NMarc Zyngier <marc.zyngier@arm.com> Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
-
由 Christoffer Dall 提交于
Rework the VGIC initialization slightly to allow initialization of the vgic cpu-specific state even if the irqchip (the VGIC) hasn't been created by user space yet. This is safe, because the vgic data structures are already allocated when the CPU is allocated if VGIC support is compiled into the kernel. Further, the init process does not depend on any other information and the sacrifice is a slight performance degradation for creating VMs in the no-VGIC case. The reason is that the new device control API doesn't mandate creating the VGIC before creating the VCPU and it is unreasonable to require user space to create the VGIC before creating the VCPUs. At the same time move the irqchip_in_kernel check out of kvm_vcpu_first_run_init and into the init function to make the per-vcpu and global init functions symmetric and add comments on the exported functions making it a bit easier to understand the init flow by only looking at vgic.c. Acked-by: NMarc Zyngier <marc.zyngier@arm.com> Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
-
由 Andre Przywara 提交于
For migration to work we need to save (and later restore) the state of each core's virtual generic timer. Since this is per VCPU, we can use the [gs]et_one_reg ioctl and export the three needed registers (control, counter, compare value). Though they live in cp15 space, we don't use the existing list, since they need special accessor functions and the arch timer is optional. Acked-by: NMarc Zynger <marc.zyngier@arm.com> Signed-off-by: NAndre Przywara <andre.przywara@linaro.org> Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
-
由 Christoffer Dall 提交于
Initialize the cntvoff at kvm_init_vm time, not before running the VCPUs at the first time because that will overwrite any potentially restored values from user space. Cc: Andre Przywara <andre.przywara@linaro.org> Acked-by: NMarc Zynger <marc.zyngier@arm.com> Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
-
由 Christoffer Dall 提交于
The current KVM implementation of PSCI returns INVALID_PARAMETERS if the waitqueue for the corresponding CPU is not active. This does not seem correct, since KVM should not care what the specific thread is doing, for example, user space may not have called KVM_RUN on this VCPU yet or the thread may be busy looping to user space because it received a signal; this is really up to the user space implementation. Instead we should check specifically that the CPU is marked as being turned off, regardless of the VCPU thread state, and if it is, we shall simply clear the pause flag on the CPU and wake up the thread if it happens to be blocked for us. Further, the implementation seems to be racy when executing multiple VCPU threads. There really isn't a reasonable user space programming scheme to ensure all secondary CPUs have reached kvm_vcpu_first_run_init before turning on the boot CPU. Therefore, set the pause flag on the vcpu at VCPU init time (which can reasonably be expected to be completed for all CPUs by user space before running any VCPUs) and clear both this flag and the feature (in case the feature can somehow get set again in the future) and ping the waitqueue on turning on a VCPU using PSCI. Reported-by: NPeter Maydell <peter.maydell@linaro.org> Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
-
- 21 12月, 2013 2 次提交
-
-
由 Marcelo Tosatti 提交于
It is possible for __direct_map to be called on invalid root_hpa (-1), two examples: 1) try_async_pf -> can_do_async_pf -> vmx_interrupt_allowed -> nested_vmx_vmexit 2) vmx_handle_exit -> vmx_interrupt_allowed -> nested_vmx_vmexit Then to load_vmcs12_host_state and kvm_mmu_reset_context. Check for this possibility, let fault exception be regenerated. BZ: https://bugzilla.redhat.com/show_bug.cgi?id=924916Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com> Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
由 Jan Kiszka 提交于
If kvm_get_dr or kvm_set_dr reports that it raised a fault, we must not advance the instruction pointer. Otherwise the exception will hit the wrong instruction. Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com> Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
- 18 12月, 2013 2 次提交
-
-
由 Jan Kiszka 提交于
It's a pathological case, but still a valid one: If L1 disables APIC virtualization and also allows L2 to directly write to the APIC page, we have to forcibly enable APIC virtualization while in L2 if the in-kernel APIC is in use. This allows to run the direct interrupt test case in the vmx unit test without x2APIC. Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com> Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
由 Anup Patel 提交于
Fix minor typo in "Parameters:" of KVM_ARM_VCPU_INIT documentation. Signed-off-by: NAnup Patel <anup.patel@linaro.org> Signed-off-by: NPranavkumar Sawargaonkar <pranavkumar@linaro.org> Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
-