It's either

        bool
        default y

or

        def_bool y

but not a mixture of both.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Since May 8 2007 the symbols RTC_INTF_PROC, RTC_INTF_SYSFS and
RTC_INTF_DEV are not tristate anymore.  This fixes the following
warnings:

arch/arm/configs/picotux200_defconfig:1072:warning: symbol value 'm' invalid for RTC_INTF_SYSFS
arch/arm/configs/picotux200_defconfig:1073:warning: symbol value 'm' invalid for RTC_INTF_PROC
arch/arm/configs/picotux200_defconfig:1074:warning: symbol value 'm' invalid for RTC_INTF_DEV
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Robert Schwebel <r.schwebel@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Simon Richter <Simon.Richter@kleinhenz.com>
Cc: Andrew Victor <linux@maxim.org.za>

... not kstop_machine.  Add a note that irqs are disabled.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

... as it is defined with memcpy, therefore no copy_page symbol to
export.
Signed-off-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

these warnings:

  arch/x86/kernel/paravirt-spinlocks.c: In function ‘default_spin_lock_flags’:
  arch/x86/kernel/paravirt-spinlocks.c:12: warning: passing argument 1 of ‘__raw_spin_lock’ from incompatible pointer type
  arch/x86/kernel/paravirt-spinlocks.c: At top level:
  arch/x86/kernel/paravirt-spinlocks.c:11: warning: ‘default_spin_lock_flags’ defined but not used

showed that the prototype of default_spin_lock_flags() was confused about
what type spinlocks have.

the proper type on UP is raw_spinlock_t.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: minor fix
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>

Impact: minor fix
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>

Impact: cleanup
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>

Impact: bugfix
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>

Impact: bugfix in iommu_map_page function
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>

On ARMv6 and later CPUs, it is possible for userspace processes to
get stuck on a misaligned load or store due to the "ignore fault"
setting; unlike previous CPUs, retrying the instruction without
the 'A' bit set does not always cause the load to succeed.

We have no real option but to default to fixing up alignment faults
on these CPUs, and having the CPU fix up those misaligned accesses
which it can.
Reported-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Commit 8ec53663 ("[ARM] Improve
non-executable support") added support for detecting non-executable
stack binaries.  One of the things it does is to make READ_IMPLIES_EXEC
be set in ->personality if we are running on a CPU that doesn't support
the XN ("Execute Never") page table bit or if we are running a binary
that needs an executable stack.

This exposed a latent bug in ARM's asm/processor.h due to which we'll
end up placing the stack at a very low address, where it will bump into
the heap on any application that uses significant amount of stack or
heap or both, causing many interesting crashes.

Fix this by testing the ADDR_LIMIT_32BIT bit in ->personality instead
of testing for equality against PER_LINUX_32BIT.
Reviewed-by: NNicolas Pitre <nico@marvell.com>
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The 440x5 core in the Virtex5 uses the 440A type machine check
(ie, they have MCSRR0/MCSRR1). They thus need to call the
appropriate fixup function to hook the right variant of the
exception.

Without this, all machine checks become fatal due to loss
of context when entering the exception handler.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

It should be 'lose', not 'loose'.
Signed-off-by: NNick Andrew <nick@nick-andrew.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This is needed so that Vitesse 7385 5-port switch could work on
MPC8349E-mITX boards.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

When the o32 errno was changed to ENOSYS, we forgot to update the code
for 64bit kernels.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Acked-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The syscall code was assuming splice only takes 4 arguments so no stack
arguments were being copied from the userspace stack to the kernel stack.
As the result splice was likely to fail with EINVAL.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

After adding the RTC platform device to malta-platform.c malta-mtd.c should
get unified with the rest of the platform device code.

These haven't seen much attention for too long but particularly important
enable RTC_CLASS and CONFIG_RTC_HCTOSYS so the wall clock time is set on
kernel startup.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

With the conversion of MIPS to RTC_LIB the old RTC driver CONFIG_RTC became
unselectable.  Fix by setting up a platform device.  Also enable
RTC_CLASS so system time gets set from RTC on kernel initialization.

[Ralf: Original patch by Tiejun; polished nice and shiny by me]
Signed-off-by: NTiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

On a 64 bit kernel if an o32 syscall was made with a syscall number less
than 4000, we would read the function from outside of the bounds of the
syscall table.  This led to non-deterministic behavior including system
crashes.

While we were at it we reworked the 32 bit version as well to use fewer
instructions.  Both 32 and 64 bit versions are use the same code now.
Signed-off-by: NVlad Malov <Vlad.Malov@caviumnetworks.com>
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Copy the FPU state to the task's thread_info->fpregs for the VIS emulation
functions to access.
Signed-off-by: NHong H. Pham <hong.pham@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Impact: fix boot crash with numcpus=0 on certain systems

Fix early exception in __get_smp_config with nosmp.

Bail out early when there is no MP table.
Reported-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Tested-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Commit 0c65f459 intended to fix truncation issues with fls() on
ARMv5+ by renaming it to __fls() and wrapping it into a C function.
However that didn't take into account the fact that __fls() already
already had different semantics in the kernel.

Let's move the __fls() code into fls() function directly, and redefine
__fls() with the appropriate semantics.  While at it, bring a generic
__fls() definition for pre ARMv5 too.
Signed-off-by: NNicolas Pitre <nico@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch fixes some bugs in VIS emulation that cause the GCC test
failure

FAIL: gcc.target/sparc/pdist-3.c execution test

for both 32-bit and 64-bit testing on hardware lacking these
instructions.  The emulation code for the pdist instruction uses
RS1(insn) for both source registers rs1 and rs2, which is obviously
wrong and leads to the instruction doing nothing (the observed
problem), and further inspection of the code shows that RS1 uses a
shift of 24 and RD a shift of 25, which clearly cannot both be right;
examining SPARC documentation indicates the correct shift for RS1 is
14.

This patch fixes the bug if single-stepping over the affected
instruction in the debugger, but not if the testcase is run
standalone.  For that, Wind River has another patch I hope they will
send as a followup to this patch submission.
Signed-off-by: NJoseph Myers <joseph@codesourcery.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce into the MN10300 gdbstub 16550 driver a couple of barrier() calls to
replace the removed volatility of the input/output index variables for the Rx
ring buffer.  A previous patch added them into the on-chip serial port driver.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

bitops_64.h includes the generic one; pretty sure 32 should too.

(Found by using __fls in generic code and breaking sparc defconfig build:
 thanks Stephen and linux-next!)
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Alan Jenkins wrote:
> This is on an EeePC 701, /proc/cpuinfo as attached.
>
> Is this expected?  Will the next release work?
>
> Thanks, Alan
>
> # opcontrol --setup --no-vmlinux
> cpu_type 'unset' is not valid
> you should upgrade oprofile or force the use of timer mode
>
> # opcontrol -v
> opcontrol: oprofile 0.9.4 compiled on Nov 29 2008 22:44:10
>
> # cat /dev/oprofile/cpu_type
> i386/p6
> # uname -r
> 2.6.28-rc6eeepc

Hi Alan,

Looking at the kernel driver code for oprofile it can return the "i386/p6" for
the cpu_type. However, looking at the user-space oprofile code there isn't the
matching entry in libop/op_cpu_type.c or the events/unit_mask files in
events/i386 directory.

The Intel AP-485 says this is a "Intel Pentium M processor model D". Seems like
the oprofile kernel driver should be identifying the processor as "i386/p6_mobile"

The driver identification code doesn't look quite right in nmi_init.c

http://git.kernel.org/?p=linux/kernel/git/sfr/linux-next.git;a=blob;f=arch/x86/oprofile/nmi_int.c;h=022cd41ea9b4106e5884277096e80e9088a7c7a9;hb=HEAD

has:

409         case 10 ... 13:
410                 *cpu_type = "i386/p6";
411                 break;

Referring to the Intel AP-485:
case 10 and 11 should produce "i386/piii"
case 13 should produce "i386/p6_mobile"

I didn't see anything for case 12.

Something like the attached patch. I don't have a celeron machine to verify that
changes in this area of the kernel fix thing.

-Will
Signed-off-by: NWilliam Cohen <wcohen@redhat.com>
Tested-by: NAlan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: NAndi Kleen <ak@linux.intel.com>
Signed-off-by: NRobert Richter <robert.richter@amd.com>

Just found the merge issue in 44274698
("powerpc/83xx: Add support for MCU microcontroller in .dts files"):
the commit adds the MCU controller node into the DMA node, which is
wrong because the MCU sits on the I2C bus. Fix this by moving the MCU
node into the I2C controller node.

The original patch[1] was OK though. ;-)
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

If oprofile statically compiled in kernel, a cpu unplug triggers
a panic in ppro_stop(), because a NULL pointer is dereferenced.
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NRobert Richter <robert.richter@amd.com>

The access to the iommu->need_sync member needs to be protected by the
iommu->lock. Otherwise this is a possible race condition. Fix it with
this patch.
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>

In some rare cases a request can arrive an IOMMU with its originial
requestor id even it is aliased. Handle this by setting the device table
entry to the same protection domain for the original and the aliased
requestor id.
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>

Remove 16 bytes of padding from struct amd_iommu on 64bit builds
reducing its size to 120 bytes, allowing it to span one fewer
cachelines.
Signed-off-by: NRichard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>

Impact: remove stale IOTLB entries

In the non-default nofullflush case the GART is only flushed when
next_bit wraps around. But it can happen that an unmap operation unmaps
memory which is behind the current next_bit location. If these addresses
are reused it may result in stale GART IO/TLB entries. Fix this by
setting the GART next_bit always behind an unmapped location.
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

From: Chris Torek <chris.torek@windriver.com>

>The SPARC64 kernel code for PTRACE_SETFPREGS64 appears to be an exact copy 
>of that for PTRACE_GETFPREGS64.  This means that gdbserver and native 
>64-bit GDB cannot set floating-point registers.

It looks like a simple typo.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On PowerPC 4xx or other non cache-coherent platforms, we lost the
appropriate cache flushing in dma_map_sg() when merging the 32 and
64-bit DMA code (commit 4fc665b8,
"powerpc: Merge 32 and 64-bit dma code").  This restores it.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NBecky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This fixes the MN10300 kernel module linking to match the toolchain.  RELA
relocs don't use the value at the location being relocated.  This has been
working because the tools always leave the value at the target location
cleared.
Signed-off-by: NMark Salter <msalter@redhat.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In the CONFIG_SMP case the irq_choose_cpu() code was returning back
a logical cpu id not the physical id.  We were writing that directly
into the HW register.

We need to be calling get_hard_smp_processor_id() so irq_choose_cpu()
always returns a physical cpu id.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The function field is 3 bits.
Signed-off-by: NSaeed Bishara <saeed@marvell.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>